Parkside PASSK 20-Li A1 Cordless Vehicle Impact Wrench
This document is the user manual for the Parkside PASSK 20-Li A1 Cordless Vehicle Impact Wrench. It provides essential information for safe operation, use, and disposal of the product.
Introduction
Congratulations on your purchase of this high-quality Parkside product. This manual is an integral part of the product and contains important safety, usage, and disposal information. Familiarize yourself with all operating and safety instructions before using the product. Use the product only as described and for the intended applications. Pass on all documentation when transferring the product to a third party.
Intended Use
This tool is designed for screwing and unscrewing screws, as well as tightening and loosening nuts. It features forward/reverse operation, a 1/2" square tool holder, and an LED work light to illuminate the immediate work area. The rotary hammer function converts motor power into uniform rotary impacts, utilized during tightening and loosening. The tool is intended for use by adults. Adolescents over 16 years of age may only use the tool under supervision. The manufacturer is not liable for damages caused by misuse or incorrect operation. Using the tool for any purpose other than intended or modifying it is considered misuse and poses a significant risk of injury.
Equipment
The impact wrench includes the following components:
- 1. Tool holder
- 2. Direction switch / lock
- 3. Belt clip
- 4. Battery status button
- 5. Battery display LED
- 6. Battery pack
- 7. Battery pack release button
- 8. LED work light
- 9. Torque selection button
- 10. ON/OFF switch / speed control
- 11. Sockets (17/19/21/23 mm)
- 12. Fast charger
- 13. Red charging indicator LED
- 14. Green charging indicator LED
Scope of Delivery
The package includes:
- 1 x Parkside PASSK 20-Li A1 Cordless Vehicle Impact Wrench
- 1 x PLG 20 A2 Battery Fast Charger
- 1 x PAP 20 A2 Battery Pack
- 4 x Sockets (17/19/21/23 mm)
- 1 x Belt clip
- 1 x Carrying case
- 1 x User Manual
Technical Data
| Specification | Value |
|---|---|
| Model | PASSK 20-Li A1 |
| Rated Voltage | 20 V DC |
| No-load Speed | 0–2300 min⁻¹ |
| Number of Impacts | 0–3000 min⁻¹ |
| Max. Torque | 400 Nm |
| Torque Selection | 5 steps (100/150/200/300/400 Nm) |
| Tool Holder | 1/2" |
Battery and Charger Information
Battery
- Type: LITHIUM-ION
- Rated Voltage: 20 V DC
- Capacity: 3 Ah
- Cells: 10
Charger
- Model: PLG 20 A2
- Input: 230–240 V ~ 50 Hz (AC)
- Power Consumption: 85 W
- Fuse: 3.15 A T3.15A
- Output Voltage: 21.5 V DC
- Output Current: 3.5 A
- Charging Time: Approx. 60 min
- Protection Class: II (double insulation)
Noise and Vibration Emissions
Noise Emissions
- Sound Pressure Level (L_PA): 91.6 dB(A) (Uncertainty K_PA: 3 dB)
- Sound Power Level (L_WA): 102.6 dB(A) (Uncertainty K_WA: 3 dB)
Vibration Emissions
- Total Vibration Values (vector sum of three directions) for tightening screws and nuts of maximum permissible size: a_h = 8.65 m/s² (Uncertainty K = 1.5 m/s²)
Wear hearing protection! ?
Safety Instructions
General Safety for Power Tools
WARNING! Read all safety instructions and warnings. Failure to follow may result in electric shock, fire, or serious injury. Keep these instructions for future reference.
Workplace Safety
- Keep work area clean and well-lit.
- Do not operate in explosive atmospheres containing flammable liquids, gases, or dust. Sparks from the tool can ignite dust or vapors.
- Keep children and unauthorized persons away from the work area.
Electrical Safety
- Ensure plugs match sockets and are not modified.
- Avoid body contact with earthed surfaces.
- Protect tools from rain and moisture.
- Handle power cords carefully, keeping them away from heat, oil, sharp edges, and moving parts.
- Use only approved extension cords for outdoor use.
- Use an RCD (Residual Current Device) if operating in damp conditions.
Personal Safety
- Stay alert, use common sense, and do not use the tool when tired, under the influence of drugs, alcohol, or medication.
- Wear appropriate Personal Protective Equipment (PPE), including safety glasses ?, hearing protection ?, and suitable clothing.
- Ensure the tool is switched off before connecting to power or battery, or before picking it up.
- Remove any adjustment tools or wrenches before switching on the tool.
- Maintain a stable stance and balance for better control.
- Do not wear loose clothing or jewelry, and keep hair away from moving parts.
Specific Safety Instructions for Impact Wrenches
- Wear hearing protection.
- Secure the workpiece firmly.
- Hold the tool firmly; high reaction torques may occur.
- Wait for the tool to stop completely before setting it down.
- Hold the tool by insulated grip surfaces when working near hidden electrical wiring.
Safety Instructions for Chargers
- This device can be used by children aged 8 and up, and persons with reduced physical, sensory, or mental capabilities, if supervised or instructed on safe use and potential hazards. Children must not play with the device. Cleaning and user maintenance must not be performed by children without supervision.
- If the power cord is damaged, it must be replaced by the manufacturer, its service agent, or a similarly qualified person to avoid hazards.
- The charger is intended for indoor use only.
Battery Safety
- Only use the specified battery pack (PAP 20 A2) and fast charger (PLG 20 A2).
- Never charge the battery pack if the ambient temperature is below 10°C or above 40°C.
- Do not charge the battery pack if the red LED blinks (overheated) or if both red and green LEDs blink (faulty).
- Keep batteries away from metal objects like paper clips, coins, keys, nails, and screws to prevent short circuits.
- Avoid contact with battery liquid; rinse immediately with water if contact occurs. Seek medical attention if liquid gets into eyes.
- CAUTION! EXPLOSION HAZARD! Never charge non-rechargeable batteries. Protect batteries from heat, direct sunlight, fire, water, and moisture.
Before Operation
Charging the Battery Pack
Unplug the charger from the mains before inserting or removing the battery pack. Charge the battery pack within an ambient temperature range of 10°C to 40°C. Insert the battery pack into the fast charger and plug the charger into the socket. The red LED indicates charging, and the green LED indicates charging is complete and the battery is ready for use. If the red LED blinks, the battery is overheated and cannot be charged. If both red and green LEDs blink, the battery pack is faulty. After charging, slide the battery pack into the tool. Allow the charger to cool down for at least 15 minutes between charging cycles.
Inserting/Removing the Battery Pack
- To insert: Set the direction switch to the middle position (lock). Slide the battery pack into the handle until it clicks into place.
- To remove: Press the release button and remove the battery pack.
Checking Battery Status
Press the battery status button to check the charge level. The battery display LEDs indicate the charge status: Green/Orange/Red = maximum charge, Red/Orange = medium charge, Red = low charge (requires charging).
Operation
Switching On/Off
- To switch on: Press and hold the ON/OFF switch. The LED work light illuminates when the switch is pressed lightly or fully, providing illumination in poor lighting conditions.
- To switch off: Release the ON/OFF switch.
Setting/Selecting Speed/Torque
Press the torque selection button to choose the desired torque step-by-step. Light pressure on the ON/OFF switch results in low speed/torque; increasing pressure increases speed/torque. The actual tightening torque should always be checked with a torque wrench. The integrated motor brake ensures quick stopping.
Changing Direction
Change the direction of rotation by pressing the direction switch to the right or left.
Attaching the Socket
Push one of the supplied sockets onto the tool holder.
Maintenance and Cleaning
WARNING! RISK OF INJURY! Switch off the tool and remove the battery pack before performing any work on it.
The tool is maintenance-free. Keep the tool clean, dry, and free from oil or grease. Do not allow liquids to enter the tool. Clean the housing with a dry cloth. Never use petrol, solvents, or abrasive cleaners. For long-term storage of the lithium-ion battery, regularly check its charge level. An optimal charge level is between 50% and 80%. The ideal storage climate is cool and dry.
NOTE: Unlisted spare parts (e.g., carbon brushes, switches) can be ordered via the service hotline.
Warranty
Kompernass Handels GmbH provides a 3-year warranty from the date of purchase. This warranty covers material or manufacturing defects. It does not cover parts subject to normal wear and tear, or damage to fragile components. The warranty is void if the product is damaged, misused, or improperly maintained. For proper use, follow all instructions in this manual. The product is for private use only.
Service
Repairs should only be carried out by qualified personnel using original spare parts to ensure product safety. Contact the service center for any issues. Service Germany: Tel.: 0800 5435 111, E-Mail: kompernass@lidl.de. Service Austria: Tel.: 0820 201 222, E-Mail: kompernass@lidl.at. Service Switzerland: Tel.: 0842 665566, E-Mail: kompernass@lidl.ch. The importer's address is KOMPERNASS HANDELS GMBH, BURGSTRASSE 21, DE-44867 BOCHUM, GERMANY.
Disposal
Dispose of packaging materials responsibly through local recycling facilities. Do not dispose of electrical tools or batteries in household waste. Follow European directives for separate collection and recycling of electrical and electronic equipment and batteries.
Declaration of Conformity
KOMPERNASS HANDELS GMBH declares that this product complies with relevant EU directives and harmonized standards. Product type: Akku-KFZ-Drehschlagschrauber PASSK 20-Li A1. Year of manufacture: 11-2017. Serial number: IAN 292020.
Ordering Spare Batteries
Replacement batteries can be ordered online at www.kompernass.com or by phone. The price is 25 EUR including VAT and shipping. For online ordering, visit www.kompernass.com, select your country/language, navigate to the 'Zubehör-Shop' (Accessories Shop), and find the appropriate battery. Follow the checkout process. If online ordering is not available in your region, contact the service hotline. The offer is limited to one battery per customer/device for two months after the promotion period.
External Links
- For manuals, videos, and software: www.lidl-service.com
- For accessories and spare parts: www.kompernass.com
