Woodbridge B0980S Electronic Bidet Toilet: Installation and Care Guide

Content

The document outlines the following sections:

1. Safety instructions
2. Technical specification
3. List of materials
4. Dimension/technical data
5. Parts identification
6. Installation of ceramic toilet
7. Previous preparation
8. Auto lid open/close
9. Daily maintenance
10. Emergency troubleshooting
11. The illustration of Main Unit Keys
12. Troubleshooting Guide
13. Warranty Card

Safety Instructions

Please read the instructions carefully before installation and keep them available for future maintenance or reference. Failure to observe these instructions can cause body injury and property damage.

Symbol Illustration

• Warning ⚠️: Indicates that failure to follow the instruction may cause serious injury or a fatal.
• Caution ❗: Indicates that failure to follow the instruction may cause body injury or property damage.

Symbol Illustration

General Warnings:

• Do not throw cigarettes and other burning stuff into the toilet, otherwise it might cause fire.
• Never disassemble, repair, or modify this product. Doing so may cause fire or electrical shock.
• Do not wash the main unit or electrical plug with water or detergent. Doing so may cause fire or electrical shock.
• Do not handle the electrical plug with wet hands. Doing so may cause electrical shock.
• It is prohibited to use other electric appliances in the same socket.
• It is forbidden to use a power extension or unstable loose outlet; otherwise, it may cause fire or electrical shock.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard.
• This product is an electric appliance, so it must be placed far away from water. Do not drench it with urine or other liquids.
• Do not put hands or other objects over the outlet of the air dryer or block the outlet of the air dryer. Doing so may cause burns and electrical shock.
• Do not lay on the side or upside down the product during the electrical circuit connection, to avoid fire or burning.
• Do not install or use the product in wet places such as a steam room.
• This product must be reliably grounded, and ensure that the AC socket is grounded to the earth. The ground lead should be used with a three-pin socket. If you are unsure whether it is reliably grounded, a qualified electrician or maintenance personnel should help to check and ensure. The electrical power source socket wiring should have a null line and a fire line. Never reverse power line wiring.

Mandatory Activities & Warnings:

• This product should be used with 110V, 50Hz electrical current only, with a load current of at least 13A. The power plug must be equipped with a ground fault circuit interrupter or a ground fault electrical leakage protector or a similar high-sensitive, rapid-type leakage switch (Rated sensitive current under 6mA).
• It is recommended to use a water-proof electrical outlet which should be installed in a place not easily exposed to water.
• The old aging water supply hose cannot be used, otherwise it might cause leakage, fire, or electrical shock. Installation of the bidet seat should include specified components and a new water supply hose.
• When moving the product from a cold or wet environment into a normal room temperature, wait for 2 hours until the condensation water is fully volatilized. Doing so can prevent the product from electrical short-circuit.
• When it thunders, it is strongly recommended to pull out the power plug.
• Do not use the product in places close to a bathtub or water tank.
• Do not place the product in water or other liquids.
• If the product falls into liquids, immediately pull out the power plug.
• Do not stand on the ceramic toilet. Do not hit the ceramic. A heavy impact on the ceramic can lead to damage and water leakage.
• Never embed the ceramic toilet base in cementitious material (such as cement mortar). It may lead to expansion cracks.
• Do not stand on the product unit, seat, or cover.
• Do not use lacquer thinner, petrol, liquid medicine, detergent, insecticide, toilet cleanser, or scrubbing brush to clean the product.
• Only use tap water or potable water; otherwise, it may cause chafing. Exposure to direct sunlight is prohibited.
• This product is equipped with a soft-closing seal cover. Heavy pressing or pushing may damage the soft-closing damper.
• Do not connect water supply to the heater outlet. Make sure the inlet water temperature is between 3~35°C; exceeding the specified range will result in the built-in heating module not working. Do not lean against the seat cover when using the product to avoid damage. Do not try flushing newsprint, diapers, sanitary napkins, or other items that can easily clog the toilet.
• Stop using the product and shut off the power when the product malfunctions; please contact service personnel for professional service.
• When installing, disassembling, repairing, and maintaining the product, you must unplug the power supply and close the water supply valve.
• Do not use in an environment below 0°C. If the room temperature is below 0°C, the water in the tank must be discharged to prevent the tank from freezing. If it is not used for a long time, the power must be turned off and the water in the water tank should be discharged.
• When used by people (including children) who lack physical, sensory, intellectual abilities, or lack of experience and common sense, this product needs to be used under the supervision of a person. Patients with heart disease should use it with caution.
• Do not let children play with this product.
• To prevent damage caused by freezing, please implement warmth measures to increase the temperature of the toilet.

Technical Specification

The following table details the technical specifications of the Woodbridge B0980S Electronic Bidet Toilet:

List of Materials

The following components are included with the product:

• Main Unit (Electronic Bidet Toilet)
• Remote controller components
• Sealing Flange
• Installation Cardboard (templates)
• Installation Manual
• Warranty Card
• Hose (for water connection)
• Mounting accessory kit (bolts, nuts, washers)

Dimension/Technical Data

Diagrams illustrating the dimensions of the Woodbridge B0980S Electronic Bidet Toilet are provided. Key dimensions include:

• Overall height: 39 inches
• Seat height: 19-1/4 inches
• Depth: 22-1/4 inches
• Rough-in distance: 12 inches
• Seat dimensions: approximately 19-7/8" length, 15-5/8" width.
• Various other measurements for width, depth, and component placement are detailed in the diagrams.

Note: Product drawings are for reference only; Woodbridge reserves the right to modify the appearance of the product. If the appearance changes, the actual product shall prevail.

Installation Option

The installation guide details connection points and placement:

• Water Inlet Connection: Connect the water inlet and angle valve with the flexible hose.
• Installation Types:
• Standard Installation: Shows toilet placement relative to floor, water outlet (angle valve mounting), and wall power outlet (GFCI).
• No Show Installation: Similar to standard, but may imply concealed plumbing.
• Dimensions: Diagrams indicate recommended locations for remote control mounting and measurements for rough-in and height relative to the wall and floor.

Parts Identification

The electronic bidet toilet components are identified as follows:

• Main Unit Exterior: Lid, Bumper, Seat, Porcelain Bowl.
• Left Side Panel: Buttons for Flush, Front cleaning, Rear cleaning, Stop/ECO.
• Right Side Panel: Power cord, Manual flush button, Deodorization window, Remote sensing window. A sensing area for foot activation (optional) is indicated.
• Internal Components (viewed from top/rear): Spray nozzle, Drying baffle.

Installation of Ceramic Toilet

The installation process involves several steps:

1. Mating Angle Valve Installation: Draw a centerline on the floor and install the angle valve on the wall according to the toilet's dimensions.
2. Cardboard Installation: Use provided cardboard templates to align with the drain outlet centerline and draw the toilet's contour line on the floor.
3. Flexible Hose Connection: Connect one end of the new hose to the toilet's water inlet and tighten it.
4. Mounting Bracket Installation: Assemble the mounting bracket with bolts, then install it onto the pre-installed flange plate on the ground and secure with nuts.
5. Porcelain Toilet Installation: Install the sealing flange into the drain outlet. Place the ceramic toilet onto the corresponding position according to the contour line. Tip: The toilet is heavy; two people are recommended for carrying.
6. Screw Installation: Insert screws through fixing sleeves, then through the toilet's mounting holes into the bracket on the ground, and tighten with a tool. Place decorative caps on the fixing sleeves.
7. Hose to Angle Valve Connection: Connect the other end of the new hose to the angle valve and tighten it.
8. Silicone Sealant Application: Apply high-quality mildew-resistant glass glue around the lower edge of the toilet base for sealing. Tips: Clean the drain outlet and ensure the toilet sits perfectly on it.

Previous Preparation

1. Turn on the Angle Valve: Check the thread connection for leaks. Unscrew the angle valve counterclockwise to its maximum opening. (Tip: The handle may have higher torque when opening for the first time).
2. Power Connection: Insert the power line leakage protection plug into the power socket. Press the reset switch; the indicator light should illuminate, indicating power is on. Tip: Press the electric leakage test button before usage; a popped-up reset switch indicates the leakage protection function is normal. Test monthly. This applies to models with a leakage protection plug.
3. Self-Inspection: The unit performs a self-inspection indicated by buzzer sounds and indicator lights (blue, then red). A second beep signifies completion. The unit then starts in normal function mode.

Auto Lid Open/Close and Foot-Sensing Function

The electronic toilet offers automatic lid open/close and foot-sensing features:

• Auto Lid Open: When a user approaches, the human body sensing window detects their presence, activating indicator lights, and the seat cover opens automatically.
• Auto Lid Close: The seat cover closes automatically 180 seconds after the user leaves.
• Male User Stand-to-Use: The seat can be opened by remote control or hand. The lid and seat close 180 seconds after the user leaves.
• Foot-Sensing Operation:
• When the lid and seat are closed, touching the sensing area with your foot opens the toilet lid.
• When the lid is open and the seat is closed, touching the sensing area with your foot opens the seat.
• When both lid and seat are open, touching the sensing area with your foot activates a half flush.

Daily Maintenance

Main Unit Care and Maintenance

1. Shut off power supply before maintenance.
2. Wipe stains with a soft, damp cloth.
3. After cleaning, reconnect the toilet to the power supply.

Spray Nozzle Maintenance and Care

1. Nozzle Self-Cleaning: When no user is seated, press the "Rear Wash/massage" button on the main unit. The nozzle will automatically extend and eject washing water.
2. Spray Nozzle Disassembly: When the nozzle moves forward, it can be disassembled for cleaning.
3. Cleaning the Nozzle Wand: Use a soft cloth or soft brush to clean. Do not pull or push the wand to avoid damage.
4. Nozzle Retraction: Put the nozzle back to the front of the boom and press the "Stop" button to automatically retract the nozzle.

Emergency Troubleshooting

Maintenance of Filter Net

Time for Maintenance: When water pressure is normal but flush performance is poor.

1. Unscrew the angle valve nut.
2. Remove the filter net.
3. Use a toothbrush to clean the filter net.
4. Reinstall the filter net and angle valve nut.

Electricity and Water Supply Cut-off

1. No Power: Activate flushing by pressing the flush button manually.
2. No Water Supply: Flush the toilet bowl with approximately 2 gallons of water. Note: Avoid water spilling from the bowl.

Troubleshooting

Failure of Remote Control

1. Operation: Operate the buttons directly on the Smart bidet seat.
2. Battery Replacement: Remove the remote control from its wall bracket. Open the battery cover, replace the battery, and put it back into the bracket. Tip: When replacing the battery, the remote control settings may reset to default and require re-configuration.

When the Product is Left Unused for Long Time

Especially in winter, if no one is home for an extended period, drain the water inside the tank and pipe to prevent freezing.

• To Discharge Water:
• Drain the water inside the tank: Turn off the angle valve, then flush all water inside by pressing and holding the manual flush button.
• Drain the water inside the pipe: Unscrew the hose connector from the angle valve, drain the water from the pipe, and then reinstall.
• Unplug and cut off the electricity.
• Handle the remaining water in the bowl: It is suggested to put some antifreeze into the water inside the bowl.
• Tips: Make sure to turn on the water supply and power when you use the toilet again. Note: Before water discharging, the power must be cut off.

Illustration of Main Unit Keys

The main unit buttons and their functions are illustrated:

• Stop Button: Press and hold to enter shutdown mode (red light off). Press again to return to working mode (red light on). In shutdown mode, all buttons except "Stop" are invalid. When the user is seated, pressing "Stop" halts washing or drying functions. When not seated, repeated "Stop" presses switch between working mode (red light) and power save mode (blue light).
• Rear Washing/Massage Button: When seated, press to wash the rear portion. Press repeatedly to toggle mobile massage function. Press "Stop" to halt. After cleaning, if the user remains seated, the drying function automatically activates. When not seated, pressing this button extends the wand for manual cleaning; press "Stop" to retract.
• Front Washing/Massage Button: When seated, press to wash the front portion. Press repeatedly to toggle mobile massage function. Press "Stop" to halt. After cleaning, if the user remains seated, the drying function automatically activates.
• Flush Button: When seated, long-press to activate the drying function. It stops automatically after one cycle. Press "Stop" to interrupt drying. In non-off mode, a short press activates the flush function. (Flush is invalid during rear or feminine wash; it activates after nozzle retraction when manually cleaned).

Tips:

• Power light off / Energy saving light on: Energy saving mode.
• Power light on / Energy saving light off: Working mode.
• All lights off: Standby mode.
• The default setting for all functions is the middle level. After using the controller, the unit shifts to the last set level.

Troubleshooting Guide

Caution:

• If problems cannot be solved by the above methods, please shut off the power and contact service providers for maintenance.
• If the leakage circuit breaker frequently trips off, it means the product has electricity leakage. Please shut off the power and contact a service provider for maintenance.

Product Warranty Card

Details regarding the product warranty are provided, including fields for Model No., Customer Name, Seller, Date of Purchased, Invoice No., Customer contact, and Distributor/Phone. The product is warranted for One (1) year from the purchasing date for free repair of defects in workmanship, provided it is used according to the installation manual and intended purposes. The company reserves the right to replace the product with similar models. Service charges may apply after the warranty period or for damages caused by user negligence, improper installation, misuse, incorrect power supply, dirt/impurities, force majeure, or failure to comply with the manual. Users are advised to fill in details correctly and keep the warranty and receipt for service. A three-year warranty for free repair service is mentioned for specific items listed in the warranty.