StarTech.com 4-Port Industrial USB Hub

Product Diagram and Components

The USB Hub features several components, detailed in the table below:

Diagram Description: The product diagram illustrates the front and rear views of the StarTech.com 4-Port Industrial USB Hub. Key components are identified with numbers: 1. USB Host Port (USB-B, screw locking), 2. DC 2-Wire Terminal Block Power Input, 3. DC Power Input (likely barrel jack), 4. Four USB Data/Charge Ports (USB-A, screw locking) with LEDs, and 5. Mounting Brackets. The diagram also shows the included USB-A to USB-B cable and the terminal block connector.

Package Contents

• USB Hub x 1
• 6 ft [1.8 m] USB-A to USB-B Cable x 1
• Terminal Block Connector (Attached)
• DIN Rail Mounting Brackets (with Mounting Screws) x 2
• Quick-Start Guide x 1

Requirements

• Computer with a USB-A Port
• 5-24V DC Power Source

For the latest drivers, manuals, product information, technical specifications, and declarations of conformance, please visit: www.StarTech.com/5G4AINDNP-USB-A-HUB

Installation

General Notes

• Connect the Power Source after all other installation steps are completed.
• The USB Hub can be powered using an external DC Power Adapter or a Terminal Block Power Source (Voltage: +5 - 24 V DC).

Connect the USB Ports

1. Connect up to four USB peripherals to the Screw Locking USB Data/Charge Ports on the USB Hub.
2. Use the USB-A to USB-B Cables to connect a USB port on each Computer to the USB Host Port on the USB Hub.

The Computer will automatically detect the device and install the required drivers.

Powering the Hub

Power the Hub Using the 2-Wire Terminal Block

1. Remove the Terminal Block Connector Housing from the USB Hub's Casing.
2. Loosen the screws for the Terminals on the Terminal Block Connector using a Flat Head Screwdriver.
3. Connect the Positive (+) and Negative (-) Wires from the 5-24V DC Power Source (not included) to the corresponding Terminals on the Terminal Block Connector. Note: Ensure the polarity of the power input is correctly matched with the DC 2-Wire Terminal Block Pins to function properly and prevent damage to the USB Hub and connected peripherals.
4. Insert the Terminal Block Connector Housing back into the USB Hub.

Diagram Description: A simplified diagram shows the DC 2-Wire Terminal Block with two screw terminals labeled 'V- (GND)' for the negative wire and 'V+ (5~24V)' for the positive wire. A power source with positive (+) and negative (-) wires is depicted connecting to these terminals, emphasizing correct polarity alignment.

Power the Hub Using an External Power Adapter

Connect a Power Adapter (not included) to the Power Input Port, located on the front of the USB Hub, and to an AC Electrical Outlet.

DIN Rail Mounting

This USB Hub includes DIN Rail Brackets for horizontal mounting to a DIN Rail. To install the DIN Rail Brackets:

1. Align the DIN Rail Brackets (x 2) with the DIN Rail Mounting Holes located on either side at the back of the USB Hub.
2. Insert the Mounting Screws (x 4) through the DIN Rail Brackets and into the USB Hub.
3. Using a Phillips Head Screwdriver, tighten the Mounting Screws. Be careful not to over-tighten.

Legal and Compliance Information

Trademarks

This manual may reference trademarks, registered trademarks, and other protected names/symbols of third-party companies. Such references are for illustrative purposes only and do not imply endorsement by StarTech.com. All trademarks, registered trademarks, service marks, and protected names/symbols are the property of their respective holders.

Warranty Information

This product is backed by a 2-year warranty. For terms and conditions, please refer to www.startech.com/warranty.

Limitation of Liability

StarTech.com Ltd. and StarTech.com USA LLP (including their officers, directors, employees, or agents) shall not be liable for any damages (direct, indirect, special, punitive, incidental, consequential, or otherwise), loss of profits, business, or pecuniary loss arising from the use of the product, exceeding the actual price paid for the product. Some states may not allow limitations on incidental or consequential damages, so these exclusions may not apply.

Company Information

• StarTech.com Ltd.
  45 Artisans Cres
  London, Ontario N5V 5E9
  Canada
• StarTech.com LLP
  4490 South Hamilton Road
  Groveport, Ohio 43125
  U.S.A.
• StarTech.com Ltd.
  Unit B, Pinnacle 15
  Gowerton Rd,
  Northampton NN4 7BW
  United Kingdom
• StarTech.com Ltd.
  Siriusdreef 17-27
  2132 WT Hoofddorp
  The Netherlands

For support in different regions:

• FR: startech.com/fr
• DE: startech.com/de
• ES: startech.com/es
• NL: startech.com/nl
• IT: startech.com/it
• JP: startech.com/jp

Regulatory Compliance

FCC - Part 15

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If not installed and used per instructions, it may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If interference occurs, users are encouraged to correct it by:

• Connecting the equipment to an outlet on a different circuit than the receiver.
• Consulting the dealer or an experienced radio/TV technician.

This device complies with part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by StarTech.com could void the user's authority to operate the equipment.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. CAN ICES-3 (B)/NMB-3(B)

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.