Jasco ZW6309A Smart Flood/Freeze Sensor with Humidity Sensor

Product Overview

This document provides instructions for the Jasco ZW6309A Smart Flood/Freeze Sensor with Humidity Sensor. It is a Z-Wave certified device designed to detect water leaks and temperature changes, transmitting notifications to a connected controller.

Key Features:

• Z-Wave certified for simple pairing and integrated home automation.
• Transmits notifications to connected controller when water leaks or temperature changes are detected.
• Dual-detection options: contacts on the sensor base or a separate plug-in detection probe for hard-to-reach locations.
• Red LED indicates programming changes and status.
• Audible alarm for leak notification.
• Supports association with up to five devices.
• Easy auto-pairing and button-press settings.
• Automatic tamper switch with alarm.
• Regular temperature and battery level reports.

Specifications

Specifications subject to change without notice due to continuing product improvement.

Installation

The smart flood/freeze sensor is designed for indoor use only. Place the sensor near areas of potential leaks or water sources such as sinks, toilets, dishwashers, washing machines, or hot-water tanks.

Sensor Placement:

• The sensor can be placed on the floor or cabinet base. The three pins on the bottom are designed to contact water leaks. These pins are recessed so they do not contact the surface (See Figure 1).
• The sensor can be safely placed on a metal surface without activation.
• Mounting tape (included) can be applied to the bottom of the sensor for secure placement (See Figure 2).

Using the Detachable Probe:

• For hard-to-reach locations, use the mounting tape to attach the sensor to a wall.
• Open the sensor port to insert the detachable probe (See Figure 3).
• Secure the probe with the pins pointed down using smaller mounting tape (included) (See Figure 4). The contact pins are slightly recessed (See Figure 5).

Power Options:

The sensor has two power options:

• Battery Power: Uses one CR123A battery (included). The signal repeater function is disabled to conserve battery life.
• USB Power: Connect an optional micro USB cable to the power port and plug into any 5V USB power supply (adapter and cable sold separately) (See Figure 6).

Note: If the power option is changed, the sensor must be removed, manually reset, and added to the network again for the signal repeater function to update.

Adding Your Sensor to a Z-Wave Network

The flood/freeze sensor can be added automatically or manually, using either battery or USB power. For best results, add the sensor near its intended location to ensure optimal communication routes.

SmartStart Inclusion:

If your controller supports SmartStart, scan the Z-Wave QR Code (found under the battery door or on the package) when prompted by your controller or hub. The sensor will be added automatically within 10 minutes of being powered up and within range of the Z-Wave network.

Manual Inclusion:

1. Follow your Z-Wave controller's instructions to add the sensor.
2. When the controller is ready, remove the top cover of the sensor (See Figure 7).
3. Ensure the battery is installed correctly (with tab removed) (See Figure 8) or the micro USB is plugged in (See Figure 9).
4. Press and release the programming button on the sensor (See Figure 10). The red LED will flash quickly.
5. If prompted by the controller, enter the S2 security code found on the product label or packaging.
6. The red LED will activate for three seconds to confirm the sensor has been added.
7. Secure the top cover.

Note: Your controller may need to be within 10 feet of the sensor during pairing.

Managing the Sensor

Removing from Z-Wave Network:

1. Follow your Z-Wave controller's instructions to remove the sensor.
2. Press and release the programming button once on the sensor (See Figure 10).
3. The red LED will blink five times to indicate removal. Secure the top cover.

Returning to Factory Defaults:

This process removes the sensor from the Z-Wave network. Use this if your primary controller is missing or inoperable.

1. Press the programming button 10 times within six seconds (no more than one second between presses).
2. The red LED will activate for two seconds, followed by three quick flashes to confirm the reset. Secure the top cover.

Replacing the Battery:

1. Remove the top cover (See Figure 7).
2. Remove the old battery and install a new one, ensuring correct polarity.
3. Secure the top cover.

Z-Wave Interoperability

This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from different manufacturers. Non-battery operated nodes within the network will act as repeaters to increase network reliability.

Accessories

Purchase compatible accessories, such as the 9ft. Micro USB Cable (36601) and USB Power Adapter (35702), at www.byjasco.com/USB or your local retailer.

Other compatible Jasco/Enbrighten Z-Wave devices include:

• In-Wall Smart Dimmers
• Plug-in Smart Dimmers
• In-Wall Add-on Switches
• In-Wall Motion Switch or Dimmer
• Plug-in Smart Switches
• In-Wall Smart Switches
• Enbrighten Smart LED Bulb
• In-Wall Smart Fan Control
• Hinge Pin Smart Door Sensor
• Direct Wire, 40A Outdoor Smart Switch
• Portable Smart Multi Sensor
• In-Wall Tamper-Resistant Smart Outlet
• Plug-in Outdoor Smart Switch

Support and Contact

For problems or questions, contact Jasco Consumer Care in the U.S. at 1-800-654-8483 (option 1), Monday–Friday, 7 AM–8 PM Central Time.

For the most up-to-date product support, accessories, and electronic manuals, visit www.byjasco.com/support.

Important Safety Information

⚠️ WARNING:

• For indoor use only.
• Battery may leak harmful liquids or ignitable materials or explode, causing injury and product damage.
• Replace exhausted battery immediately.
• Remove battery if product is to be unused for extended periods.
• Do not use Z-Wave devices to control electric heaters or any other appliances which may present a hazardous condition due to unattended, unintentional, or automatic power-on control.
• Z-Wave enabled devices should never be used to supply power to or control the on/off status of medical or life-support equipment.

FCC/IC Compliance

This device complies with Part 15 of the FCC and Industry Canada license-exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications. Such modifications could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

To comply with FCC RF exposure requirements, no changes to the antenna or device are permitted.

FCC ID: U2ZZW6309 | IC: 6924A-ZW6309

Warranty

Jasco Products Company warrants this product to be free from manufacturing defects for five years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specific rights, and you may also have other rights which vary from state to state. Please contact Jasco Consumer Care at 1-800-654-8483 (option 1) or visit www.byjasco.com if the unit should prove defective within the warranty period.