ENERMAX T.B. RGB AD Fan Pack: Specifications, Installation, and Control Guide
Chapter 1: Specifications
| Model Number | Dimension (mm) | Speed (RPM) | Air Flow (CFM) | Air Flow (m³/h) | Static Pressure (mm-H₂O) | Noise Level (dBA) | Rated Current-Fan (A) | Rated Current-ARGB LED (A) | Rated Voltage (V) | ARGB Rated Voltage (V) | MTTF (hours) | Connector |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| UCTBRGBA12P-BP3 | 120(W) x 120(H) x 25(D) | 500 ~ 1500 (±10%) | 13.71 ~ 47.53 | 23.29 ~ 80.75 | 0.19 ~ 1.66 | 14 ~ 22 | 0.15 | 0.8 | 12 | 5 | ≥160,000 hours @ 25°C | 1x 4 pin PWM connector, 1x 4 pin ARGB connector (5V/D/-/G) |
For detailed information, please visit the ENERMAX website at www.enermax.com.
Chapter 2: Part List
Included Accessories:
- 3 x ENERMAX RGB Fans
- 1 x ENERMAX RGB Control Box
- 1 x Control Box Power Cable (SATA)
- 1 x ARGB 3 to 1 Cable (5V/D/-/G)
- 1 x GIGABYTE ARGB Adapter
- 1 x PWM 3 to 1 Cable
- 1 x Molex Adapter
- 12 x Screws
- 1 x Magnetic Adhesive (For Control Box)
Chapter 3: 3 Fan Pack Installation Guide
Fan Connection
PWM Connection: Use the PWM 3-to-1 cable to connect three fans. Then, connect the fan connector to the PWM header on the motherboard.
Diagram Description: Shows three fans connected in series via a PWM 3-to-1 cable, which then connects to the motherboard's 4-pin PWM header.
RGB Lighting Synchronization
There are two ways to control the RGB lighting:
- Using the ENERMAX RGB Control Box.
- Synchronizing with the motherboard's Addressable RGB header.
Method 1: Using the RGB Control Box
Connect the fans to the RGB Control Box using the ARGB 3-to-1 cable. Power the RGB Control Box using the provided SATA power cable from the PSU.
Diagram Description: Illustrates connecting three fans to the ENERMAX RGB Control Box via an ARGB 3-to-1 cable. The Control Box is powered by a SATA connector from the PSU.
Method 2: Addressable Motherboard Sync
Connect the fans (or the ARGB 3-to-1 cable) directly to the motherboard's Addressable RGB Header (typically a 5V/D/-/G connector). Ensure the fans are connected to the correct header on the motherboard.
Diagram Description: Shows fans connected directly to the motherboard's Addressable RGB Header (5V/D/-/G).
Note: The maximum current for the RGB Control Box is 3A.
Chapter 4: RGB Control Box Operation
The RGB Control Box allows for customization of fan lighting effects, speed, and brightness.
Mode Indicators
The 4 LED colors on the control box indicate the current mode:
- GREEN: Light Effect Mode
- RED: Effect Speed Mode
- BLUE: Brightness Mode
- YELLOW: Auto-run Mode
Controlling Light Effects (GREEN LED)
- Press the [Mode Button] ('M') until the LED turns GREEN.
- To change the effect, press the [Up Arrow] or [Down Arrow] buttons.
- There are 10 pre-set light effects:
- ① Racing-Rainbow (Default)
- ② Breathing-Rainbow
- ③ Flash-Rainbow
- ④ Overlaying-Rainbow
- ⑤ Flow-Rainbow
- ⑥ Colors auto-run (8 colors) - Press [Up Arrow] for 3 seconds to fix the current color. Press [Up Arrow] for 3 seconds again to return to the Colors auto-run effect.
- ⑦ Ripple auto-run (8 colors)
- ⑧ Overlaying-RED
- ⑨ Overlaying-GREEN
- ⑩ Overlaying-BLUE
- Pressing the [Down Arrow] button for 3 seconds will return to the default "Racing-Rainbow" effect.
Controlling Brightness (BLUE LED)
- Press the [Mode Button] ('M') until the LED turns BLUE.
- To adjust the brightness, press the [Up Arrow] or [Down Arrow] buttons.
- Pressing the [Mode Button] ('M') for 3 seconds in any mode will turn off the lights. Pressing the [Mode Button] ('M') again will turn on the lights and resume the previous effect.
Controlling Effect Speed (RED LED)
- Press the [Mode Button] ('M') until the LED turns RED.
- To change the effect speed, press the [Up Arrow] or [Down Arrow] buttons.
Auto-run Mode (YELLOW LED)
- Press the [Mode Button] ('M') until the LED turns YELLOW.
- In Auto-run Mode, all 10 pre-set light effects run in a loop.
