GrandPatio Napoli Hanging Umbrella with Big Base

Important Information

There are two installation methods for this product. This manual applies if you are using a thick umbrella stand as shown in the figure.

Before beginning assembly, ensure all parts are present by comparing them with the package contents list and hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.

This item is heavy. Use care when handling. Assembly may require two adults for safety.

Assemble the umbrella on a stable, non-abrasive surface, such as carpeting, to prevent damage.

Care and Maintenance

Use mild soap and warm water for cleaning. Avoid abrasive materials, cleaners, or bleach products. Rinse with clean water and dry thoroughly.

Water accumulation inside the frames can freeze and damage the frame tubing. Such damage is not covered under warranty.

During inclement weather and winter periods, close the umbrella and store it in a dry area. A matching umbrella cover is strongly recommended to extend its lifespan.

Package Contents

• Part A: Main canopy frame (x1)
• Part B: Curved pole section (x1)
• Part C: Base unit (x1)
• Part D: Base connector/mount (x1)
• Part E: Plastic caps for base (x2)
• Part E1: Valve/plug for base (x1)
• Part F: Base crossbar (x1)
• Part G: Base crossbar (x1)
• Part H: Pole support/connector (x1)
• Part I: Wheel assembly (x2)
• Part J: Wheel axle/pin (x1)
• Part S: Securing strap (x1)

ATTENTION: Parts C, D, E, and E1 are in carton 2.

Hardware Contents

• Hardware K: Bolts (x4)
• Hardware L: Bolts (x3)
• Hardware M: Bolts (x1)
• Hardware N: Bolts (x1)
• Hardware O: Pins/clips (x1)
• Hardware P: Strap (x1)
• Hardware Q: Wrench (x1)
• Hardware R: Nuts (x1)
• Hardware T: Bolts/screws (x2)

Assembly Instructions

Step 1

Connect base crossbars F and G. Attach wheel assemblies I to the crossbars.

Step 2

Attach the pole support H to the assembled base frame. Secure it using bolts K and nuts R.

Step 3

Attach the wheel assembly I and axle J to the pole support H.

Step 4

Prepare the base unit C by inserting the valve E1 and plastic caps E.

Step 5

Mount the prepared base unit C onto the pole support H. Secure the base unit to the frame using bolts T and L.

Step 6

Insert and tighten the valve E1 and plastic caps E onto the base unit C.

Step 7

Fill the base unit C with water and sand until it is full. The base requires a minimum weight of 264 LBS (approximately 120 kg) for stability.

Step 8

Ensure the plastic caps E on the base are fully tightened. CAUTION: The Cap must be fully tightened.

Step 9

Attach the base connector D to the base unit C.

Step 10

Connect the main canopy frame A to the curved pole section B. Attach this assembly to the main pole support using bolts T and M.

Step 11

If the mounting holes of Part A are not visible, follow the detailed sub-steps (1-7) which involve attaching components using hardware P and other fasteners to secure the pole assembly.

• Sub-step 1-4: Attach bracket or connector as shown.
• Sub-step 5-7: Secure the pole assembly using the provided hardware.

Step 12

Connect the curved pole section B to the base support H. Attach the base connector D to the base unit C. Secure the main pole assembly to the base using bolts N, T, and the wrench Q.

Step 13

Secure the pole assembly using pin/clip O.

Operation Instructions

Step 1

Adjust the umbrella height by rotating the control knob. [Rotate knob ↻]

Step 2

Adjust the umbrella height by rotating the control knob. [Rotate knob ↻]

Step 3

Open the umbrella canopy. [Open umbrella ▶️]

Step 4

Close the umbrella canopy. [Close umbrella ◀️]

Step 5

Adjust the umbrella's angle and position. The mechanism allows for rotation and tilting. [Adjust angle ?]

Step 6

Secure the closed umbrella canopy using the strap S. [Secure with strap ✔️]

General Operation

Position the umbrella to provide shade from the sun. The base can be tilted up to 35 degrees [Tilt base ≤35°] to maneuver the umbrella into the desired position. Two people are recommended for moving the umbrella.

Care and Storage Instructions

CAUTION: The umbrella must be retracted during extreme weather. Damage resulting from failure to comply, such as torn fabric or broken ribs/pole, is excluded from warranty coverage. [Retract in bad weather ☁️❌]

When not in use, secure the umbrella with the P strap. Do not leave the umbrella unattended. Avoid stepping on the base. [Secure strap ✔️, No step ??]

Umbrella Cloth Replacement

Replacing the umbrella cloth requires careful handling and potentially assistance.

Step 1

With the help of others and possibly a ladder, carefully detach the old umbrella cloth from the frame.

Step 2

Follow the detailed sub-steps (1-3) to release the cloth from the frame's ribs.

Step 3

Attach the new umbrella cloth to the frame, ensuring it is correctly positioned.

Step 4

Secure the new cloth to the frame, verifying proper attachment. [Check attachment ✔️]

Step 5

Repeat the process of detaching and attaching the cloth, following sub-steps (1-4) for each section of the frame.

Step 6

Ensure the new cloth is properly fitted and secured to the umbrella frame.