Midea Stand Fan Owner's Manual
Model: FS40-19K
CAUTION
Read Rules for Safe Operation and Instructions Carefully.
WARNING
- If the supply cord is damaged, it must be replaced by manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
- Indoor use only.
- To protect against the risk of electrical shock, do not immerse the unit, cord or plug in water or other liquid.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
- When the appliance is not in use and before cleaning, unplug the appliance from the outlet.
- When the fan was assembled, the rotor blade guard shall not be taken off anymore.
- Correct Disposal of this product: This product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
RULES FOR SAFE OPERATION
- Never insert fingers, pencils, or any other object through the grille when fan is running.
- Disconnect fan when moving from one location to another.
- Be sure fan is on a stable surface when operating to avoid overturning.
- DO NOT use fan in window, rain may create electrical hazard.
- Household use only.
INSTALLATION INSTRUCTIONS
Name of components
Considerate Hint: If you choose to install the pole, it will become the Stand Fan. If you choose to install the connector, it will become the Table Fan.
Base Installation
Align the column with the groove on the base and fix them together using a right-angle bolt.
Diagram showing base, right-angle bolt, pole, connector, motor, and rear grill. Arrows indicate assembly steps: 1. Connect base and pole. 2. Tighten knob. 3. Install motor and rear grill by aligning.
Front and Rear Guard Installation
Diagrams illustrating the installation of the front and rear guards:
- Align Catch of the Front Guard with the illustrated position of the Rear Guard.
- Press guards sequentially with both hands.
- Self-Catch Installation: Secure the guard using the Guard Catch.
Diagram showing the blade installation:
- Step 4: Attach the rear guard using the lock nut of grill (screw clockwise).
- Step 5 & 6: Attach the blade onto the motor shaft and secure with the lock nut of blade (turn anticlockwise).
- Step 7: Install the front fan cover.
Lock nut of blade: Lock nut of blade anticlockwise, and then install the front fan cover.
Blade: Pull the blade to rotate after installing, so as to ensure that the blade can be normally rotated.
Lock nut of grill: Screw the lock nut of grill clockwise, and in the meantime, fix the rear grill.
INSTRUCTIONS FOR USE
Instructions for operation of body
Diagram of the fan with controls labeled:
- Body Key: Buttons labeled 0, 1, 2, 3 for fan speed control.
- Height Adjustment: Turn counterclockwise and loosen the Height Adjustment Key for performing height adjustment.
MAINTENANCE INSTRUCTION
The fan requires little maintenance. Do not try to fix it by yourself. Refer it to qualified service personnel if service is needed.
- Before cleaning and assembling, fan must be unplugged.
- To ensure adequate air circulation to the motor, keep vents at the rear of the motor free of dust. Do not disassemble the fan to remove dust.
- Please wipe the exterior parts with a soft cloth soaking a mild detergent.
- Do not use any abrasive detergent or solvents to avoid scratching the surface. Do not use any of the following as a cleaner: gasoline, thinner.
- Do not allow water or any other liquid into the motor housing or interior parts.
CLEANING
- Be sure to unplug from the electrical supply source before cleaning.
- Plastic parts should be cleaned with a soft cloth moisten with mild soap. Thoroughly remove soap film with dry cloth.
Warranty Details
Changes to Warranty card invalidates the warranty.
Dealer Stamp
Model No.: FS40-19K
Serial No.:
Product: Stand Fan
Date of expiry of warranty:
Customer Details
To be filled in upon purchase
Customers Name & Address:
Tel. No./Email:
Date of purchase:
Service History
To be filled in case of warranty repair
| Job no. | Date | Job no. | Date | Job no. | Date |
|---|---|---|---|---|---|
Midea offers the owner of this product a ONE YEAR WARRANTY, from the date of purchase, against all manufacturing defects in material and workmanship. The warranty card to be presented to authorized service centers / distributors along with the purchase invoice to claim the warranty.
The warranty does not cover:
- Damage due to mishandling or fire and becomes invalid if repair has been attempted by unauthorized persons.
- Any failure to follow the instructions as mentioned in the user manual.
- Fluctuation in voltage or any modifications/adjustments made to comply with local electrical, safety and technical standards.
- Damages caused by fire, accident or any natural disaster, damage due to mishandling, wear & tear, voltage fluctuations.
GD Midea Environment Appliances MFG.Co.,Ltd. No.28, Dong Fu Road, Hesui East Industrial Area, Dong Feng Town, Zhongshan, Guangdong 528425 P.R.China
