XbotGo RC1 Remote Controller User Manual

Remote Controller Specifications

Quick Start Guide

Follow these steps to get your XbotGo RC1 Remote Controller up and running.

Basic Functions

1. Power On/Off: Press and hold the power button [power button] for X seconds.
2. Function Selection: Press the function selection button to cycle through different modes.
3. Bluetooth Pairing:
   • Press and hold the power button. The phone connection indicator will flash red.
   • Open the XbotGo APP on your device.
   • Select "XbotR-XXXX" in the APP for pairing.
   • Upon successful connection, the indicator light turns solid blue.

Using the Remote Controller

Signal Range: If the remote controller exceeds the XX meter signal range, the red menu indicator light and circular ring light will flash, indicating disconnection. Re-entering the reception range within 1 minute will automatically restore the connection, indicated by a solid blue light.

[Sleep Mode] and Shutdown: The remote controller enters [sleep mode] after a period of inactivity. Press any button to wake it. It will automatically shut down after five minutes in [sleep mode]. Press the power button to restart.

Note: Disconnection does not affect the running APP. If the APP cannot find the remote controller, reset it by pressing the power button for X seconds and re-pairing.

Buttons and Functions

Familiarize yourself with the remote controller's buttons before use:

• A. Power Button: Turns the remote controller on and off.
• B. Function Selection Button: Cycles through camera, photo, and steering modes.
• C. Confirm Button: Used to take photos, start/pause video, or mark highlights.
• D. Directional Buttons (Circular Disk): Controls movement or gimbal direction.
• E. Battery Compartment: Houses the CR2032 battery.

Camera Function

Switch to camera mode using the Function Selection button. Use the Confirm button to control shooting:

• On the Remote Controller: A "beep" sound indicates entry into camera mode. Two consecutive "beep-beep" sounds indicate the camera is paused or not active.
• On the APP: A temporary blue mask appears on the screen, indicating camera mode is active.

Photo Function

Switch to photo mode using the Function Selection button. Press the Confirm button to capture a photo.

Steering Function

Switch to steering mode using the Function Selection button. Use the Directional Buttons (Up, Down, Left, Right) to control the gimbal's direction.

Mark Function (Available during Camera Function mode)

Manually mark highlight moments during operation. The XbotGo APP records video segments before and after the marked moment, automatically generating a highlight video. A blue circular ring light flashes upon successful marking. View highlights in XbotGo App/Cloud Management/Cloud Drive.

Battery

The remote controller is equipped with a CR2032 button battery.

Notes: For optimal performance, do not use different types of batteries. If the device will not be used for over two months, remove the battery.

Battery Disposal: Do not dispose of batteries as unsorted municipal waste. Please refer to local regulations for proper battery disposal.

Notes on Remote Controller

• The remote controller must be used within XX meters of the device.
• The APP will provide pairing prompts when the remote control signal is received.

Regulatory Information

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.

ISED Statement

English: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

French: Cet appareil contient des émetteurs/récepteurs exempts de licence qui sont conformes aux CNR exempts de licence d'Innovation, Sciences et Développement économique Canada. Le fonctionnement est soumis aux deux conditions suivantes : (1) Cet appareil ne doit pas causer d'interférences. (2) Cet appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer un fonctionnement indésirable de l'appareil.

This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance.

cet appareil est conforme à l'exemption des limites d'évaluation courante dans la section 2.5 du cnr - 102 et conformité avec rss 102 de l'exposition aux rf, les utilisateurs peuvent obtenir des données canadiennes sur l'exposition aux champs rf et la conformité.

This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator & your body.

Cet équipement est conforme Canada limites d'exposition aux radiations dans un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 0 cm entre le radiateur et votre corps.