XbotGo RC1 Remote Controller User Manual

Remote Controller Specifications

Model: XbotGo RC

Battery Model: CR2032

Signal Coverage Range: 10 meters

Operating Temperature: 0°C to 40°C (32°F to 104°F)

Quick Start Guide

Follow these steps to get started:

1. Battery Installation: Open the battery compartment cover, remove the insulating plastic sheet from the bottom of the battery, and close the cover.

   Diagram Description: Shows opening the battery compartment, removing a plastic sheet, and closing the cover.

2. Power On/Off: Press and hold the [Power Button] for a few seconds to turn the remote controller on or off.
3. Function Selection: After powering on, press the [Function Selection Button] to switch between different functions.
4. Bluetooth Pairing:
   • Press and hold the [Power Button]. The phone connection indicator will flash red.
   • Open the XbotGo APP on your phone and select "XbotR-XXXX" for pairing.
   • Once connected, the phone connection indicator will turn solid blue.
5. Signal Range: If the remote controller exceeds the signal range (approx. 10 meters), the red menu indicator light and circular ring light will flash, indicating disconnection. The connection will automatically restore when back within range (within 1 minute).
6. Sleep Mode and Shutdown: The remote controller enters sleep mode after a period of inactivity. Press any button to wake it. It will automatically shut down after five minutes of sleep. Press the [Power Button] to turn it back on.

Note: If the APP cannot find the remote controller, press and hold the [Power Button] for three seconds to reset it and re-pair.

XbotGo RC1 Remote Controller Layout

Familiarize yourself with the buttons:

• A. [Power Button]: Turns the controller on/off.
• B. [Function Selection Button]: Cycles through available functions (Camera, Photo, Steering, Mark).
• C. [Confirm Button]: Used to take photos, start/pause video, or mark moments.
• D. [Directional Buttons (Circular Disk)]: Controls movement or camera gimbal direction.
• E. [Battery Compartment]: Houses the CR2032 battery.

Diagram Description: Illustrates the physical layout of the XbotGo RC1 remote controller with buttons labeled A through E.

Buttons and Functions

Camera Function

Press the [Function Selection Button] to switch to camera mode. Press the [Confirm Button] to control shooting states.

• On the remote controller: A single "beep" indicates entry into camera mode. Two consecutive "beep-beep" sounds indicate the camera is paused or not activated.
• On the APP side: A temporary blue mask appears on the screen, indicating camera mode is active.

Photo Function

Press the [Function Selection Button] to switch to photo mode. Press the [Confirm Button] to capture a photo.

Steering Function

Press the [Function Selection Button] to switch to steering mode. Use the [Directional Buttons] to rotate the gimbal or control movement.

Mark Function (Available during camera function mode)

Manually mark highlight moments during recording. Pressing the [Confirm Button] records video segments before and after the marked moment. A blue circular ring light flashes upon successful marking. Highlights can be viewed in the XbotGo App under Cloud Management/Cloud Drive.

Battery

The remote controller uses a CR2032 button battery.

Notes

• For optimal performance, do not mix battery types.
• Remove the battery if the device will not be used for over two months.

Battery Disposal:

Do not dispose of batteries as unsorted municipal waste. Please follow local regulations for proper disposal.

Notes on Remote Controller

• The remote controller must be used within 10 meters of the device.
• The App will prompt for pairing when the remote control signal is received.

FCC Warning and Compliance

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.