User Manual for Shenzhen Aintel Technologies models including: CP500RAV4G, 2AZTD-CP500RAV4G, 2AZTDCP500RAV4G, CP500 Smart Body Worn Camera, Smart Body Worn Camera
Shenzhen Aintel Technologies Co., Ltd. CP500RAV4G Smart Body Worn Camera 2AZTD-CP500RAV4G 2AZTDCP500RAV4G cp500rav4g
You Say, We Do CP500 Quick User Manual Product Introduction Main Camera Operation Indicator Video Recording Programmable Button 1 Charging Indicator Power Button Micro USB Port Secondary Camera 3.1" Color Touch Screen Removable Battery PTT Button Programmable Button 2 Photo Taking Earphone Jack Status Indicator Item Battery Status Icon View Definition Full charged Low power In charging WiFi connected but no Internet error WiFi connected access to the internet Data Network 3G/4G 3G/4G Bluetooth On GPS On Signal Indicator Flight Mode Signal Bars TF card indicator LED Operation Indicator Light Item Green light Red light flashing Definition 1.Camera Preview 2.Screen Off and Standby In Videoing Amber light flashing In Recording One-time Red light flashing In Photo Taking LED Charging Indicator Light Indicator Light Red light Green light Definition In Charging Full Charged Unpacking and Checking Install a Nano SIM Card As shown below, please take off the cover and unlock the SIM card slot, and put Nano SIM card into it and then lock it again. Install and Remove the Belt Clip Bracket 1. Align the slot on the top of device with the clamp on the bracket, and push the device down with a click to complete the installation as shown below. Install and Remove the Battery Prior to assembly, please aim at the slot on the device, make the battery protruded contact portion to accommodate the device by pressing the bottom of the battery and then lock the battery by sliding the locking button as the shown operation in sequence in the following figure. 2. Insert the belt clip from left to right as shown in figure 3 and fasten it to the undercuts. 360° rotatable design of the belt clip makes a high wearable satisfaction. 3.Hold the device with one hand, push the right undercut of the bracket with the other hand, and take the bracket off with the arrow direction as shown below. As shown below, please take off the cover and unlock the SIM card slot, and put Nano SIM card into it and then lock it again. Caution Please be sure to use our original battery. Danger of fire or explosion may be caused if Non-original battery is used or the positive and negative poles are swapped over. Battery Charging Method 1: by USB cable 1.Plug the adaptor into the power socket. 2.Connect the device with the adaptor by Mini USB cable and then enter into the charging mode if the indicator light turns red. 3.The indicator will light green when the device is full charged. Method 2: by Specified Charger (Optional) 1.Connect the charger with the power supply by he Type-C cablemake the cable loop with a counterclockwise rotation and then connect the adaptor through the lead groove as the following shownand the indicators of both terminal slot and battery slot on the charger light green. 2.Put the device with the battery into the terminal slot as shown below, and then the indicator turns red to be in charging. 3.An extra battery could be put into the battery slot concurrently, and charged if the indicator turns red. 4.The indicators would light green when the charging is completed. Getting Started Switch On Press the power button for 3 seconds under shutdown to power on. Switch Off Press the power button for 3 seconds, enter into the shutdown interface and then tap the shutdown option to power off. Video Recording In the camera preview, slide the video recording switch downward to start the video recording and upward the switch to stop it. Photo Taking In the camera preview, short press the photo taking button to enable it. Platform Login The registration on Intelligence dispatch Network server is necessary to make this product to have the multiple functions like PoC PTT calling, Video Uploading, Position Transmitting, and Instant Messaging. 1.Click on the icons as Logout, Worktable, PoC Trunking, Message, Address Book, to log on the platform. 2.Click the button More to set up the server IP, communication port and data port. 3.Click the button Confirm to save the settings and return to the login interface. 4.Please make sure 4G and WiFi connection is working, input the account and password to login. The members ID, groups and online status will be shown on the homepage. Caution Account and password will be provided by the system administrator. PoC PTT calling, Video uploading, Position Transmitting, Instant Messaging, Job Ticketing, Alarming and Geo-fencing could be enabled after a successful login. PoC PTT calling 1.Enter into groups, and press PTT button to make a call on the current group. Release the PTT button to make the call over. 2.Or, Click PoC trunking, and then press PTT to have a group call. 3.Or, Click on the icon as shown on the top right corner and select different groups to call. 4.Or, Click Address Book, and tick the user/users to make the individual call or dynamic group call. Video Upload 1.Click on the icon on the homepage to upload the current video information to the dispatcher. 2.Or, the video could be uploaded by an upward pulling with a silent transmission command on the dispatcher. Enable the Emergency Alarm Long press the programmable button which is programmed as the Emergency button (the default orange one), to enable all the on-site information including real-time audio and video, location, and terminal ID to be uploaded to the dispatcher automatically, and send a beep alarm to the dispatcher and all the members in the same group. Disable the Emergency Alarm Long Press the Emergency button to cancel it in the Emergency Alarm status. To get more features and operation details, please contact us sales@aintel.cn !Adobe Illustrator CS6 (Windows) Adobe PDF library 10.01