Firefly 2 User Manual

Contents

• Device Guide
• Using Loose Leaf
• Using Concentrates
• Cleaning
• Batteries
• Firefly App
• Tips + Tricks
• Safety

Device Guide

Meet your new best friend, the Firefly 2. It's a smart travel companion designed for smooth adventures.

LED Behavior

The LED indicator provides information about the Firefly 2's status:

• Blinking Green: Firefly 2 is heating.
• Solid Green: Firefly 2 is ready to use.
• Blinking Blue: Battery is charging.
• Solid Blue: Battery is fully charged.
• Blinking Red: Battery is low and needs charging.
• Solid Red: Firefly 2 needs to cool down.

Charging

To charge your Firefly 2:

• Plug the USB cable into a standard USB adapter and connect it to the Firefly 2 charging dock.
• Place the Firefly 2 on the charging dock. The LED will blink blue while charging and turn solid blue when fully charged.
• Keep the Firefly 2 on the charging dock when not in use.
• For fastest charging, use a wall adapter that is 9 Watts or higher. A full charge takes approximately 45 minutes with such an adapter. Lower wattage adapters may take longer.

Using Loose Leaf

Packing Loose Leaf

Follow these steps to pack loose leaf material:

• Remove the magnetic lid by lifting it up from either side.
• Use hand-torn or coarsely-ground material.
• Loosely fill the glass chamber, slightly past the rim, and tamp down gently.
• Ensure the interior surfaces are free of debris for a tight seal.
• Replace the lid, ensuring it is seated correctly.

Vaping Loose Leaf

To vape loose leaf:

• Touch and glow: Place fingers on both touch sensors to start heating.
• Important: Lightly touch the sensors, similar to tapping a smartphone. Avoid excessive force.
• The LED will blink green for three seconds and turn solid green when ready.
• On subsequent touches, the LED will turn solid green immediately.
• Keep fingers in place and inhale for 5-10 seconds.
• Release the touch sensors to stop heating.
• After a few draws, stir the contents of the heating chamber.
• For denser vapor, inhale more deeply for a few extra seconds. Refer to the Tips and Tricks section for further customization.

Please Note: The heating coil's glow may dim towards the end of a session.

Using Concentrates

Packing Concentrates

For optimal concentrate use:

• Download the Firefly app and use the “Concentrates” setting.
• Place a concentrate pad in the heating chamber and press it firmly into the bottom.
• Place a small amount of concentrate material on the center of the pad. A little goes a long way!
• Solid Concentrates: About the size of a grain of rice.
• Liquid Concentrates: 2-3 drops.
• Important: Do not overfill the pad.
• Replace the lid and ensure it is seated correctly.

Vaping Concentrates

To vape concentrates:

• Touch and Glow: Place fingers on the touch sensors to start heating.
• The LED will blink green for a few seconds and turn solid green when ready.
• Continue to hold the touch sensors while taking 5 to 10 cigar-style mouth puffs.
• After initial heating, return to normal inhalations.

Cleaning

Heating Chamber

• Clean only at room temperature or below.
• Use a toothpick to remove larger particles, then wipe clean with an alcohol wipe.
• Allow the chamber to dry completely before vaping.
• Important: Do not pour alcohol directly into the heating chamber.

Mouthpiece

• Hold the Firefly 2 in one hand and push the mouthpiece to one side with the other hand. Wiggle it left and right until removed.
• Remove any particulate with the enclosed cleaning pick.
• Replace the mouthpiece by aligning it and pushing until it clicks into place.

Vapor Path

• Use alcohol wipes to clean the surfaces of the vapor path on the chassis and the lid.
• Important: Be gentle when wiping the top lid to avoid damaging the gasket.

Concentrate Pad Removal

• Concentrate material can become sticky. Pre-heat the Firefly 2 for 10-15 seconds to loosen any material. Use the pick from the cleaning kit to pry up the edges of the pad and remove it.
• Cleaning the concentrate pads is not recommended.

Batteries

Battery Levels

To check the battery level, quickly tap the right touch sensor three times and observe the LED indicator:

• Five blue blinks: 100% charge
• Four blue blinks: 75% charge
• Three blue blinks: 50% charge
• Two blue blinks: 25% charge
• One blue blink: 10% charge
• Blinks Red: Battery is low and needs charging.

Removing and Replacing

To remove and replace the battery:

• Remove the battery door by pushing forward at the indicated arrow.
• Insert the battery into the compartment and slide the cover back into place.
• Replace the battery door: place the door on the back side of the Firefly 2, aligning the arrow side closest to the mouthpiece. Position it just above the edge of the Firefly 2 and press down from the top to click it into place.

Firefly App

The Firefly app is free and available for download on the iTunes and Android app stores, or visit www.thefirefirefly.com/support.

Settings Page

• Set heating profile
• Customize touch sensor activation
• Check battery level
• Connect Device

Information Page

• Register your Firefly 2 for immediate firmware updates, faster support, and insider information.
• Contact Firefly customer service.
• Connect to the Firefly website, social media feed, and blog.

Pair Your Device

• Ensure the Firefly 2 is fully charged and the Firefly app is open.
• Place fingers on the Firefly 2 touch sensors; the LED will blink green. Release to put the Firefly 2 in listening mode.
• The app will display a pairing screen, allowing you to select your device.
• You can create a custom name for your device if desired.
• The app will show a green checkmark to indicate a successful connection.
• The Firefly 2 will blink three times to confirm it is connected.

Heating Profiles

• Choose from 6 pre-set temperature settings.
• Once a heating profile is set in the app, the Firefly 2 will maintain that setting until a new profile is selected. The default setting is Medium High (400°F).
• Concentrates: 500°F. Important: Using the concentrates setting with loose-leaf material can cause combustion.
• High: 420°F
• Medium High (Default): 400°F
• Medium: 380°F
• Medium Low: 360°F
• Low: 340°F

Tips and Tricks

To Get More Vapor

• Take deeper, longer inhalations.
• Experiment with higher heat settings in the app (but do not use the concentrates setting for loose-leaf to avoid combustion).
• Ensure the vapor path is clear and the lid is reseated snugly.
• Remove the mouthpiece to clear any particulate matter, then replace it firmly.

Battery Life

• Keep the Firefly 2 on its charging dock to ensure a charged battery.
• Activate the touch sensors only while vaping. Remind new users to do the same for their first time.

Concentrates

• Do not overfill the pad. If concentrate has dripped onto the heating element, use the touch sensors to heat the device and blow air OUT to remove the material.

Still have a question? Check out our FAQ at www.thefirefly.com/support.

Safety

Use only Firefly cleaning implements. Never immerse the Firefly chassis in liquid. Clean the Firefly only when it is cool.

Environmental Conditions:

• Ambient Temperature: 50 - 105°F (10 ~ 40°C)
• Ambient Humidity: 65+/-20%RH

FCC Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

IC Caution:

This device complies with Industry Canada's license-exempt RSSs. Operation is subject to the following two conditions:

• (1) This device may not cause interference; and
• (2) This device must accept any interference, including interference that may cause undesired operation of the device.

Hereby, NWT Holdings Inc. declares that Firefly 2 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.

Environmentally Friendly Disposal:

You can help protect the environment! Please remember to respect the local regulations: hand in non-working electrical equipment to an appropriate waste disposal center.

CE 0700