Dynaudio Xeo 10/20/30 Owner's Manual

Hello

Welcome to Dynaudio Xeo. We’ve taken care of the tech; you take care of the music.

Introduction

Thank you for choosing Dynaudio Xeo. Xeo combines the latest wireless technology with impressive sound quality and makes listening to music truly convenient and easy. The following pages contain important information on connecting the system and its operation to ensure perfect function and the best-possible sound quality. We hope you have a great time listening to your favourite music.

About this product

The active Xeo 10/20/30 speakers are equipped with powerful integrated amplifiers and allow for the direct connection of various analog and digital audio sources. A Bluetooth interface enables the operation of Bluetooth devices and plays them back in optimal sound quality. Optional components like Xeo Hub or Dynaudio Connect enable setting up a wireless multiroom system without any restrictions to the highest sound quality. The speakers can be fully controlled with a remote control. The operational state of the system is indicated by two LEDs on the front.

About this manual

This manual describes the operation of the Xeo 10/20/30 speakers. Information about the optional Xeo modules (Hub, Connect, Extender, Link) can be found in the Owner's manual provided with these modules.

Important safety instructions

Please read and keep these instructions. Heed all warnings and follow all instructions.

• Do not use this apparatus near water.
• Clean only with a dry cloth.
• Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding-type plug. (USA and Canada only: A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.)
• Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit the apparatus.
• Only use attachments/accessories specified by the manufacturer.
• Unplug this apparatus during lightning storms or when unused for long periods of time.
• Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
• WARNING: To reduce the risk of fire or electric shock, this apparatus should not be exposed to rain or moisture and objects filled with liquids, such as vases, should not be placed on this apparatus.
• To completely disconnect this equipment from the mains, disconnect the power supply cord plug from the receptacle.
• The mains plug of the power supply cord shall remain readily operable.

Warning

Xeo 10/20/30 speakers

RISK OF ELECTRIC SHOCK! DO NOT OPEN! If the speakers are connected to the mains voltage, a dangerous electrical voltage is present inside the speakers.

• Use the supplied power cable to connect the speakers to the mains voltage. Make sure that the power supply cable is not damaged; replace it with a new one if it has been damaged.
• To reduce the risk of electric shock, do not remove the back panel and never open the speaker housing. Do not expose the speakers to rain or moisture. No user serviceable parts inside. Refer servicing to qualified personnel.
• Do not operate defective speakers and disconnect defective speakers from the mains voltage. Please contact your Dynaudio Xeo distributor if you have any problems. Distributor addresses can be found on the Internet at dynaudio.com.

Remote control battery

DANGER OF EXPLOSION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.

CHEMICAL BURN HAZARD If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.

Unpacking

After unpacking, make sure the system is complete and check the device and all accessories for transport damage. Transport damage may be expected if the packaging is already severely harmed. Do not attempt to start up a damaged device. If the contents are incomplete or damaged, please contact your Dynaudio Xeo distributor. Distributor addresses can be found on the Internet at dynaudio.com.

Removing the protection cap

The tweeter is protected by a cap to prevent damage during transport and unpacking. After you have unpacked the speaker, remove the cap by just pulling it straight out.

Packaging material

The packaging has been designed so that it may be reused as long as it has not been damaged during transport. Keep the packaging and use the original packaging for all further transport.

Disposal

Disposal of used electrical and electronic equipment (applicable in European countries with separate collection systems for this equipment): This symbol on the product or its packaging indicates that the product must not be treated as household waste. Instead, it must be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health. The recycling of materials helps to conserve natural resources. For more detailed information on recycling this product, please contact your local authority, community waste disposal office, or the shop where you purchased the product.

Scope of delivery

The Xeo 10/20/30 set includes:

• 2 x Xeo 10/20/30 speakers
• 2 x Xeo 10/20/30 speaker cloth covers
• 1 x Xeo 10/20/30 remote control
• 2 x power cables (country-specific version, length: 2.5 m)
• 1 x stereo cable (RCA – RCA, length: 1.5 m) (Xeo 10 only)
• 1 x optical cable (Toslink – Toslink, length: 1.5 m) (Xeo 10 only)
• 1 x stereo cable mini jack (3.5 mm – 3.5 mm, length: 1.5 m) (Xeo 10 only)
• 1 x Xeo first time setup manual (quick guide for installation)

Connections and control elements

This section describes the connections and control elements. Please contact your Dynaudio Xeo distributor if you have any problems with connection and start-up. Distributor addresses can be found on the Internet at dynaudio.com.

Elements on the rear panel

The Xeo 10/20/30 set consists of a master and a slave unit. The master unit carries the audio input interfaces.

Diagram Description: The rear panel features several connection ports and controls:

• A: Speaker position - A switch for sound adjustment based on speaker placement (Neutral, Wall, Corner).
• B: Speaker ID/Zone - Switches for selecting speaker placement (Left/Right) and audio zones (Red, Green, Blue).
• C: Aux In - For connecting an analog audio source via a 3.5 mm mini jack.
• D: Line In - For connecting an analog audio source via RCA connectors.
• E: Optical In (Toslink) - For connecting a digital audio source.
• F: USB In - For firmware updates only.
• G: Mains socket - For connecting the speaker to the mains voltage.
• II (master unit only) - Indicates the master unit.

Buttons on top of the cabinet (Xeo 10)

• Speaker on/off: Press to switch on the speakers. The Xeo 10 will scan inputs for an active signal. Press and hold to switch off.
• Input selection: Press to cycle through available inputs.
• Volume control: Press [volume up] or [volume down] to adjust the volume level. Press and hold for faster adjustment.
• Bluetooth pairing: Press and hold both [volume up] and [volume down] buttons to start pairing.

Remote control

Commands from the remote control apply to both speakers.

• MUTE: Press to mute or unmute the speakers.
• ON/OFF: Press to switch on the speakers. Press for standby mode. Press and hold for at least 5 seconds to put the speakers in sleep mode.
• VOLUME: Press [volume up] or [volume down] to adjust the volume level.
• INPUT: Press a button to select the respective signal source. The [Bluetooth/Hub/Connect] button selects a Bluetooth device or Hub/Connect.
• Bluetooth pairing: Press and hold for at least 5 seconds to enter pairing mode.
• Controls (for Bluetooth devices): [backward], [play/pause], [forward] buttons for media playback.

Connecting and setting up

Positioning and connecting to mains voltage

• Position the speakers in your desired location.
• Do not expose the speakers to direct sunlight, heat, or moisture.
• Do not place the speakers near devices with strong electromagnetic radiation or devices that could be destroyed or damaged by magnetic fields.
• Use the provided power cable to connect the speaker to the mains voltage.

Tip (Xeo 10): For easier access, the plate at the bottom of the cabinet can be removed. Use a coin or screwdriver to loosen the screw and attach the plate after connecting the power cable.

Cloth cover

The cloth cover is attached to the housing with magnets and does not influence the sound dispersion of the speaker. It may be removed if needed.

General settings

• In stereo mode: Select 'Left' operating mode for the left speaker and 'Right' for the right speaker.
• Speaker position: Set the speaker position switch to best match the speakers' need for acoustic compensation (Neutral for free-standing, Wall for near a wall, Corner for in a corner).
• Zone: Select the Red, Green, or Blue zone. Ensure both speakers in a stereo pair are set to the same zone for synchronized operation. (See page 26 for more information on audio zones).

Operation

Switching on

To switch the speakers on from standby mode, press the power button on top of one of the speakers (Xeo 10) or point the remote control at a speaker and press the power button. The speakers will automatically search for an active audio signal and output it (autoplay function). If no input signal is detected, the speakers will continue scanning inputs for 20 minutes before entering sleep mode. If there is no input signal, the speakers will go into standby mode after a certain period.

Playback of connected sources

Once your Xeo speaker is connected via a direct input, simply choose your desired source on the remote. The speakers will automatically detect the signal and start playback. Master and slave speakers will connect wirelessly if set to the same zone. If no signal is applied to either input, the speakers will continue scanning inputs for 20 minutes and enter sleep mode.

Playback of a Bluetooth device

After pairing your device with your Xeo 10/20/30, connect by selecting the Xeo 10/20/30 from your device's Bluetooth list. Select 'Bluetooth' on the remote control and press play on your Bluetooth device.

Disconnect

Press and hold the disconnect button [disconnect] to disconnect a connected device or disconnect directly from the device.

Fixing the volume

You can set the speaker to a higher volume using the 'fix volume' function. This setting remains active in standby mode. If a signal source has its own volume control, you can adjust the output volume across a broad range using that source's control.

To fix the volume: Point the remote control at a speaker and press the 'fix volume' button for at least 2 seconds. To undo fixing, press either of the two volume buttons.

Standby

To switch speakers to sleep mode:

Point the remote control at a speaker and press the standby button, or press the standby button on top of one of the speakers. The speakers will enter sleep mode. They also enter sleep mode if there is no audio signal for 20 minutes. In this mode, the wireless network is active, and all connected units remain synchronized. Sleep mode power consumption is less than 2 W.

To switch speakers to low-power standby mode:

Press and hold the low-power standby button [sleep] on the remote control for at least 5 seconds. The speakers enter low-power standby mode. In this mode, the wireless network is disabled, and the speakers are not connected to each other. Low-power standby mode power consumption is less than 0.5 W.

To turn off auto standby:

Press and hold the 'Opt' button on the remote control for at least 5 seconds.

Status LEDs on the front

The two LEDs in the upper left corner of the cabinet front indicate the operational state of the speakers and system with various colours and blinking functions.

¹⁾ depending on the resolution of the audio source, ²⁾ Hub, Connect, mobile device, etc.

Malfunctions

Interruptions, clicking noises, or other audible interference when playing music are usually not caused by radio transmission in the Xeo system. Often, other external causes influence the transmission quality.

Below are a few tips for improving transmission quality:

1. Position all radio transmitters and receivers away from each other. WLAN devices, radio receivers, and radio systems may influence each other if they are too close together. Test out various locations for each device.
2. Switch off the automatic search function in WLAN devices. WLAN devices and other radio systems permanently scan for available frequencies, thus sending signals that could disrupt other radio systems. This automatic search function can usually be switched off.
3. Xeo technology radio signals can transmit through walls. However, walls may consist of very different materials, such as wood fibreboard, stone, or even steel. The walls may also contain complex cable installations for electrics, phones, TVs, and radios, as well as water pipes and air shafts. These can divert radio signals. This is why you should test different locations for the Xeo Hub, Extender, and Link and favour the most direct radio path between the Xeo components.
4. Some electrical devices, such as microwaves, generate strong electromagnetic fields that could disrupt radio systems. Do not operate such electrical devices near Xeo components.

You can ask your Dynaudio Xeo distributor for assistance at any time. Or go to dynaudio.com/support to read the FAQ or to contact the Customer Support Team. Further information can also be found on the Xeo website at dynaudio.com/xeo.

Accessories

Accessories (Xeo 10)

A desk stand or wall brackets extend the range of applications of your Xeo 10 speakers. For further information, please see the website at dynaudio.com or contact your Dynaudio distributor. Distributor addresses can also be found at dynaudio.com.

Desk stand

The Dynaudio desk stand for Xeo 10 is an elegantly designed stand for placing the speakers on a desk or shelf. An installation instruction is provided with the stand.

Wall bracket

The wall bracket allows you to mount the Xeo 10 speakers on the wall.

VESA 100 bracket (Xeo 10/20)

VESA is a standard for wall brackets developed by the Video Electronics Standards Association. The Xeo 10 and Xeo 20 speakers allow you to mount brackets according to the VESA 100 standard. This means that the screws on the back plate are spaced 100 mm apart.

To mount a VESA 100 bracket (Xeo 10):

1. Loosen the four screws (Torx type) and unmount the back plate.
2. Keep the back plate for future use.
3. Follow the instructions provided with the bracket you want to mount.

Setting up

Spikes with pointed ends (Xeo 30)

Xeo 30 floor-standing speakers are delivered with spikes for permanent installation on the floor. The pointed ends of the spikes may result in injuries and damage delicate floors.

• Pay attention that you do not injure yourself with the spikes.
• We recommend inserting the spikes in aluminium feet if you have delicate floors, such as parquet or laminate.

Positioning

Position the speaker in the desired location. Do not expose the speakers to direct sunlight, heat, or moisture. Do not place the speakers near devices with strong electromagnetic radiation or devices that could be destroyed or damaged by magnetic fields.

Connection options

Connect your signal source to the appropriate input on the Xeo 10/20/30 speaker. The following table gives a selection of signal sources and options for connecting to the Xeo speaker.

Division into audio zones

The Xeo speakers (as well as Xeo Link) can be assigned to audio zones using the Zone selector switch. All components assigned to the same zone can be operated together via the remote control.

Diagram Description: The diagram illustrates a possible zone configuration showing speakers assigned to 'Red', 'Green', and 'Blue' zones within different rooms.

The Xeo system

Xeo consists of several high-quality components that are optimally matched. When combined, they can fulfil the most demanding requirements for a wireless multi-room and multi-source system.

Components of the Xeo system

Xeo speakers (Xeo 10/20/30)

The active Xeo speakers Xeo 10/20/30 receive the wireless signals from the Hub or Connect and play them back in optimal sound quality. In addition, the Xeo 10/20/30 can be connected directly to various audio sources. All speakers have an integrated amplifier and can be controlled with a remote control. Display elements indicate the operating state of the system, and controls on the cabinet allow you to switch them on/off or change the volume without using the remote control.

Xeo remote control

The Xeo remote control can be used to turn the speakers on and off, change the volume, and select a Hub or Connect and its connected signal sources.

Dynaudio Connect and Xeo Hub

The Dynaudio Connect and Xeo Hub are the control centres for the Xeo system. Both offer a new level of wireless connectivity and convenience. Signal sources such as tuners, receivers, CD players, TVs, streaming clients, network players, MP3 players, or computers are connected to them. Signals are sent wirelessly and lossless to the connected Xeo or Focus XD speakers (or Xeo Link) where they are then played back.

Xeo Extender

The Xeo Extender extends the reception range of the Xeo Hub. As a result, Xeo speakers or other Xeo components can be operated further away from the Xeo Hub or Dynaudio Connect.

Xeo Link

The Xeo Link receives wireless signals from a Xeo Hub or Dynaudio Connect and outputs analog and digital signals from its connections. As a result, you can also connect active subwoofers, active speakers, or other components to the Xeo system.

Combination examples

Below you will find several examples of Xeo component combinations. The high level of flexibility in the Xeo system enables even more variants. Ask your Dynaudio distributor to find the perfect solution for your needs.

Direct wired:

Analog/digital audio sources + Xeo 10/20/30

Direct wireless:

Bluetooth device (mobile phone, etc.) + Xeo 10/20/30

With Hub or Connect:

Analog/digital audio sources + Hub or Connect + Xeo speaker

For extended range:

Analog/digital audio sources + Hub or Connect + Extender + Xeo speaker

For additional speakers:

Analog/digital audio sources + Hub or Connect + Xeo speaker plus + Link + active component (e.g. active subwoofer, active speakers, or power amplifier and passive speakers)

Note: The Extender and Link may also be combined.

Compliance and Regulatory Information

Declaration of Conformity (EU only)

Dynaudio A/S hereby declares that the product Dynaudio Xeo 10 is in conformity with the following directives:

• 2001/95/EF (Product Safety)
• 2006/95/EF (Low Voltage directive)
• 2004/108/EF (EMC directive)
• 1999/5/EC (R&TTE directive)
• 2011/65/EU (ROHS directive)
• 1275/2008 (ErP, Ecodesign directive)

The Declaration of Conformity is available on the Internet at dynaudio.com/support/manuals.

Reminding (USA and Canada only)

A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

(French translation of FCC statement is present in the original document.)

IC NOTICE

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

(French translation of IC Notice is present in the original document.)

MPE Reminding

This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.

• The device for operation in the band 5150 – 5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
• The maximum antenna gain permitted for devices in the bands 5250 – 5350 MHz and 5470 – 5725 MHz shall comply with the e.i.r.p. limit; and
• The maximum antenna gain permitted for devices in the band 5725 – 5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.

(French translation of MPE Reminding is present in the original document.)

Technical data

All Apple products are trademarks of Apple Inc. All Sony products are trademarks of Sony Electronics Inc. All Sonos products are trademarks of Sonos Inc. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. All Google products are trademarks of Google Inc. Other trademarks and trade names are those of their respective owners.

An update to this manual may be necessary due to product improvements and new functions. The latest version of this manual is available on the Internet at dynaudio.com/support/manuals.