WATER FILTER REPLACEMENT INSTRUCTIONS

SAFETY AND WARNINGS

Water filter

IMPORTANT!

• The water connection to your ice & water refrigerator must be installed by a qualified plumber or Fisher & Paykel trained and supported service technician and comply with all state and local laws.
• Installation and use MUST comply with all state and local plumbing codes. Check with your local public works department for plumbing codes. You must follow their guidelines as you install the water filtration system.
• To avoid serious illness or death, only connect your water filter to safe drinking water.
• The water filter cartridge needs to be changed when the replacement indicator icon illuminates. This will happen every 6 months.
• If the water filtration system has been allowed to freeze, replace filter cartridge. Failure to replace the disposable filter at recommended intervals may lead to reduced filter performance and failure of the filter, causing property damage from water leakage or flooding.
• In cases of excessively reduced filter life, we recommend that you consult a local plumber or your water supplier for advice on suitable filtration requirements for the water supplied to your home.
• Filter replacement is the consumer's responsibility and will not be covered by the warranty except in the case of faulty parts or materials within the filter cartridge.
• If the water has not created ice for some time or ice has an unpleasant taste or odor, dispose of ice and refer to the flushing instructions in this book. If unpleasant taste or odor persists, you may wish to fit a new filter cartridge.
• Your water filtration system can withstand up to 120psi (827kPa) of water pressure. Ensure the supplied pressure-reducing valve is installed before installing the water filtration system. DO NOT install if water pressure exceeds 120psi (827kPa).

Rated capacity: 862285 – 750 Gallons (2839 Liters), 862288 – 120 Gallons (454 Liters)

Flow rate: 0.5 GPM (1.89 LPM)

Replacement filter cartridges can be purchased online at fisherpaykel.com or by calling Fisher & Paykel Customer Care. Details of the replacement filter cartridge are labelled on the cartridge.

To reduce the risk associated with property damage due to water leakage or flooding:

• DO NOT install systems in areas where ambient temperatures may go above 100°F (38°C) or drop below 33°F (0.6°C).
• DO NOT install on hot water supply lines. The maximum operating water temperature of this filter system is 100°F (38°C).
• DO NOT install where water hammer conditions may occur. If water hammer conditions exist, you must install a water hammer arrester.
• DO NOT use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.

FOR REFRIGERATORS WITH EXTERNAL FILTER

Note: It is not necessary to turn the water supply off when removing or installing the water filter.

Removing the old filter

Diagram showing filter removal: A hand grasps and twists the filter cartridge.

1. Grasp and firmly twist the cartridge in an anti-clockwise direction (A) (to the left when installed in the recommended orientation).

2. Pull the cartridge away from the filter head (down when installed in the recommended orientation).

• It is not unusual for a few drops of water to be present when the filter is removed.

Discard the old filter.

Installing the new filter

Diagram showing filter installation: A hand inserts and twists a new filter into the filter head.

1. Remove the plastic wrapping from the new filter and then remove the protective cap.

2. Align the filter correctly. Insert the filter into the filter head and rotate in a clockwise direction (C) (to the right when installed in the recommended orientation).

IMPORTANT!

After installation, the water filter MUST be flushed. Refer to 'Flushing the water filter' for details.

FOR ACTIVESMART™ INTEGRATED REFRIGERATORS

Note: It is not necessary to turn the water supply off when removing or installing the water filter.

Removing the old filter

The filter is located behind the toe kick grille.

1. Remove toe kick grille by inserting fingers into the left and right square openings on the grille. Pull grille towards you.
2. Pull the freezer drawer out slightly, the filter is located on the left-hand side.

Diagram showing filter removal using a tool: A filter removal tool is used to turn the cartridge counterclockwise.

3. Using the filter removal tool, align the tool to the cartridge handle and turn 90° counterclockwise to loosen (A).

4. Remove the tool, grasp firmly onto the cartridge handle and pull towards you to remove. Discard the old filter.

Installing the new filter

Diagram showing new filter preparation and installation: New filter unwrapped, then inserted and locked into place.

1. Remove the plastic wrapping from the new filter and then remove the protective cap (B).

2. Remove toe kick grille by inserting fingers into the left and right square openings on the grille. Pull grille towards you.

3. Pull the freezer drawer out slightly to access the filter casing. Align the filter correctly (C).

4. Using the filter tool, push the filter firmly inside the casing all the way into the filter head.

5. Rotate the filter head clockwise 90° to lock in place (D).

6. Ensure the filter is in the locked position (E). Remove filter removal tool and close the freezer drawer.

IMPORTANT!

After installation, the water filter MUST be flushed. Refer to 'Flushing the water filter' for details.

WATER FILTER FLUSHING INSTRUCTIONS (ALL MODELS)

Flushing the water filter

• Check your refrigerator is switched on.
• Allow at least 2 hours for your appliance to cool before use.
• Complete all the flushing steps detailed in this document to ensure optimum performance of your water filter.

For Ice & Water only models: Flushing must be completed through both the water dispenser and ice maker.

For Automatic Ice only models: Flushing must be completed through the ice maker.

Flushing through water dispenser

1. Press the water dispenser pad to dispense 1 gal (4L) of water.
2. A harmless carbon residue may be dispensed with water during the flushing process.
3. Wait for 4 minutes before dispensing again.
4. Dispense 1 gal (4L) of water then wait another 4 minutes.
5. Dispense another 1 gal (4L) of water. Your water dispenser is ready for use.
6. Water will continue to drip from the dispenser for a few more days after installation to clear remaining trapped air in the dispenser. Check the drip tray regularly and empty when required.

Flushing through ice maker

1. Turn the ice maker on, refer to the user guide supplied with your appliance for details.
2. Press the [reset buttons] together for 4 seconds then close the doors. The ice tray will flip twice and empty the water into the bin below.
3. The ice tray will flip only after the doors are closed.
4. Repeat step 2 to remove dust in the ice tray collected during manufacture and transport.
5. Empty the water from the ice bin and return it correctly.
6. Once your ice maker is turned on, the first bin of ice may be discolored, this is not harmful and normal during the flushing process. Discard the first full bin of ice made. Your ice maker is ready for use. The performance of your water filter will improve with continued use.

For Ice & Water only models: The water filter will reach optimum performance after two to three full bins of ice.

For Ice only models: The water filter will reach optimum performance after four to five full bins of ice.

Resetting the filter indicator

Use the water filter as soon as possible after installation. A replacement indicator on the control panel and/or external display illuminates when you need to replace the filter. Reset the indicator only after replacing the filter.

To reset indicator:

• Press the [reset buttons] together for 4 seconds.
• The [indicator light] on the control panel will turn off when reset.
• The filter change indicator icon on the control panel and/or external display will turn off when reset.

IMPORTANT!

• We recommend the water filter to be used from the time of installation.
• Do not reset indicator before filter is changed or filter monitoring will be inaccurate.

Certifications

Filter 862285 certified by IAPMO R&T against NSF/ANSI Standard 42 and CSA B483.1 for the reduction of claims specified on the performance data sheet and at iapmort.org.