Zooz ZEN05 800LR Outdoor Smart Plug

Features

• Z-Wave® on/off control of lights and small appliances
• IP65 rated for outdoor use
• NEW 800 series Z-Wave® chip for faster control
• Z-Wave® Long Range for ultra reliable no-mesh communication
• S2 authenticated security and SmartStart
• Supports OTA firmware updates
• ETL listed for compliance with North American safety standards

Specifications

• Model Number: ZEN05 800LR
• Z-Wave® Region: US/CA/MX
• Power: 110 VAC, 60 Hz
• Maximum Load: 15 A, 150 W LED bulbs, 1000 W incandescent, 1/3 hp motor
• Range: Up to 150 ft (up to 1300 ft with LR) line of sight
• Installation and Use: Indoor or outdoor
• IP Rating: 65
• Dimensions: 2.25" x 3.25" x 1.5"
• Cord Length: 6.5"

Z-Wave® Control

Adding a Device

Step 1: ADD DEVICE to your hub

Initiate inclusion (pairing) in your hub's app or web interface. For hub-specific instructions, scan the QR code provided with your hub or visit www.support.getzooz.com.

If using an S2 hub, you will be prompted to enter the DSK PIN or scan the QR code printed on the side of the plug's outlet for SmartStart inclusion.

Step 2: PLUG the ZEN05 into a receptacle

While the hub is searching for new devices, click the Z-Wave® button 3 times quickly. The LED indicator will flash blue to confirm inclusion mode and turn green for 1 second upon successful completion.

QR / PIN CODE: Scan the code printed on the device for SmartStart pairing. The QR codes below are for hub-specific instructions.

SmartStart enabled products can be added to a Z-Wave® network by scanning the Z-Wave® QR Code present on the product with a controller providing SmartStart inclusion.

To access step-by-step pairing instructions for your hub, scan the relevant QR code for your hub with your phone's camera:

• SmartThings: Scan QR code for SmartThings instructions.
• Z-Box Hub: Scan QR code for Z-Box Hub instructions.
• Home Assistant: Scan QR code for Home Assistant instructions.
• Hubitat: Scan QR code for Hubitat instructions.

For general support, visit www.support.getzooz.com.

Installation and Operation

Installation:

Plug the Outdoor Plug into any standard grounded 110 V receptacle. Do NOT connect any devices to the plug at this point. Click the Z-Wave® button to check if the LED indicator turns on and off. If the LED indicator does not light up, try a different receptacle. If it remains off, contact support at ask@getzooz.com.

Before You Plug Anything In:

Ensure the load you are connecting does NOT exceed 15 A. This Outdoor Plug can handle a total of 15 A. Connecting heavy-duty equipment (e.g., washers, dryers, refrigerators, or motors over 1/3 hp) will DAMAGE the device and may cause the connected appliance to malfunction.

Caution: This is an electrical device. Use caution when installing and operating. Remote control of appliances may lead to unintentional or automated activation. Do NOT use this Z-Wave® device to control electric heaters or appliances that pose a fire, burn, or electrical shock risk when unattended.

Warning:

• This product should be installed indoors upon completion of any building renovations.
• Prior to installation, store the device in a dry, dust- and mold-proof place.
• Do not install in places with direct sun exposure, high temperature, or humidity.
• Keep away from chemicals, water, and dust.
• Ensure the device is never close to any heat source or open flame.
• Ensure the device is connected to a power source that does not exceed the maximum load power.
• No part of the device may be replaced or repaired by the user.

Troubleshooting

The Outdoor Plug won't add to your hub? Try this:

1. Initiate EXCLUSION in your hub and click the Z-Wave® button 3 times quickly. Then try adding it again after successful exclusion (this acts as a reset and can be used even if the plug was never connected).
2. Click the Z-Wave® button 4-5 times quickly when adding, or try adding in non-secure mode.
3. Bring the Outdoor Plug closer to your hub; it may be out of range.
4. Double-check if the device is powered.
5. Find more troubleshooting tips for your hub at www.support.getzooz.com.

Exclusion (Removing / Unpairing Device)

1. Bring the Outdoor Plug within direct range of your Z-Wave® gateway (hub).
2. Put the Z-Wave® hub into exclusion mode (contact support at ask@getzooz.com if unsure).
3. Press and release the Z-Wave® button 3 times quickly.
4. Your hub will confirm exclusion, and the Outdoor Plug will disappear from your controller's device list.

Factory Reset

If your network's primary controller is missing or inoperable, you may need to reset the device manually. Ensure the plug is powered, then click the Z-Wave® button twice and hold it the third time for 10 seconds. The LED indicator will flash green 3 times to confirm a successful reset.

Note: All previously recorded activity and custom settings will be erased.

Association

The Outdoor Plug supports Group 1 for Lifeline communication and Group 2 with up to 5 devices for basic on/off control. This device sends a Basic Set command to Group 2 whenever its on/off status changes.

Note: Not all Z-Wave® systems provide direct access to association settings. Contact support if you need assistance finding these settings.

Advanced Settings

Refer to your controller's user guide for advanced programming instructions, as they vary by software. For detailed instructions on changing settings for SmartThings, Hubitat, and more, visit www.support.getzooz.com or email ask@getzooz.com.

To access advanced settings for your plug on your Z-Wave® system, scan the relevant QR code for your hub with your phone's camera:

• SmartThings: Scan QR code for SmartThings instructions.
• Z-Box Hub: Scan QR code for Z-Box Hub instructions.
• Home Assistant: Scan QR code for Home Assistant instructions.
• Hubitat: Scan QR code for Hubitat instructions.

Supported Command Classes:

• COMMAND_CLASS_ZWAVEPLUS_INFO_V2
• COMMAND_CLASS_SWITCH_BINARY_V2
• COMMAND_CLASS_CONFIGURATION_V4
• COMMAND_CLASS_ASSOCIATION_V2
• COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION_V3
• COMMAND_CLASS_ASSOCIATION_GRP_INFO_V3
• COMMAND_CLASS_METER_V5
• COMMAND_CLASS_TRANSPORT_SERVICE_V2
• COMMAND_CLASS_VERSION_V2
• COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2
• COMMAND_CLASS_DEVICE_RESET_LOCALLY
• COMMAND_CLASS_INDICATOR_V3
• COMMAND_CLASS_POWERLEVEL
• COMMAND_CLASS_SECURITY_2
• COMMAND_CLASS_SUPERVISION
• COMMAND_CLASS_FIRMWARE_UPDATE_MD_V5

Parameter Descriptions:

• Parameter 1: LED Indicator Behavior
  Controls how the LED indicator behaves based on the plug's on/off status. The LED flashes twice to confirm changes.
  • Values: 0 – LED on when plug is on, off when plug is off (default); 1 – LED on when plug is off, off when plug is on; 2 – LED always off; 3 – LED always on.
  • Size: 1 byte dec
  • Note: Click the Z-Wave® button 6 times quickly to manually toggle values.
• Parameter 2: Auto Turn-Off Timer
  Sets the time (in minutes) after which the Outdoor Plug automatically turns off once turned on.
  • Values: 0 – timer disabled (default); 1-65535 (minutes).
  • Size: 4 byte dec
• Parameter 4: Auto Turn-On Timer
  Sets the time (in minutes) after which the Outdoor Plug automatically turns on once turned off.
  • Values: 0 – timer disabled (default); 1-65535 (minutes).
  • Size: 4 byte dec
• Parameter 6: Power Outage Recovery State
  Determines the plug's state after a power outage.
  • Values: 0 – automatically turns OFF after power restore (ignores previous status); 1 – automatically turns ON after power restore (ignores previous status); 2 – remembers and returns to the status prior to power outage (default).
  • Size: 1 byte dec
  • Note: Click the Z-Wave® button 10 times quickly to manually toggle values.
• Parameter 7: LED Indicator Brightness
  Sets the brightness level of the LED indicator.
  • Values: 0 – bright; 1 – medium; 2 – low (default).
  • Size: 1 byte dec
  • Note: Click the Z-Wave® button 8 times quickly to manually toggle values.
• Parameter 8: Physical Button Control
  Enables or disables manual control via the physical Z-Wave® button.
  • Values: 0 – manual control disabled; 1 – manual control enabled (default).
  • Size: 1 byte dec
• Parameter 9: Power Consumption Reporting Threshold
  Sets the wattage threshold for reporting power consumption changes. The plug reports changes exceeding this value (e.g., default 5 Watts means changes of at least 5W more or less).
  • Values: 5-50. Default: 5.
  • Size: 1 byte dec
• Parameter 10: Power Consumption Reporting Frequency
  Sets how often the plug reports power consumption (in minutes).
  • Values: 1-65535. Default: 5.
  • Size: 4 byte dec

Warranty

This product is covered by a 12-month limited warranty and an extended 5-year warranty upon registration. For the full warranty policy, product registration, or to file a claim, please visit www.getzooz.com/warranty.

Compliance and Legal Information

ETL Certification: This is an ETL certified device. ETL, like UL, is a Nationally Recognized Testing Laboratory, confirming product compliance with North American safety standards.

FCC Note: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications. Such modifications could void the user's authority to operate the equipment.

Storage and Use: Store indoors when not in use. Suitable for dry locations only. Do not immerse in water. Not for use where directly exposed to water.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in any given installation.

If this equipment causes harmful interference to radio or television reception, the user may try to correct the interference by:

• Reorienting or relocating the receiving antenna.
• Increasing the separation between the equipment and receiver.
• Connecting the equipment into a separate outlet or circuit from the receiver.
• Consulting the dealer or an experienced radio/TV technician for assistance.

All brand names displayed are trademarks of their respective holders.

© Zooz 2025

Liability Limitation: In no event shall Zooz or its subsidiaries be liable for any indirect, incidental, punitive, special, or consequential damages, or damages for loss of profits, revenue, or use. Zooz's liability is expressly limited to replacement or repayment of the purchase price for the affected portion of products. All claims must be made in writing within thirty (30) days of delivery or the date fixed for delivery.