WyreStorm EXP-MX-0808-KIT Quickstart Guide
4K UHD 4:2:0 60Hz 8x8 HDBaseT™ Matrix Switch with 6 Receivers & S/PDIF De-Embed
Introduction
WyreStorm recommends reading through this document in its entirety to become familiar with the product's features prior to starting the installation process.
Key Technologies Supported: 4K HDR, HDBaseT, HDMI 2.2, HDCP 2.2, PoH
In the Box
- 1x EXP-MX-0808-KIT Matrix
- 6x EXP-MX-KIT-RX Receivers
- 1x AC Power Cord with EU pins
- 1x AC Power Cord with US pins
- 1x AC Power Cord with UK pins
- 1x AC Power Cord with AU pins
- 1x IR Remote (CR2025 Battery not Included)
- 8x IR Emitters
- 6x IR Receivers
- 2x Matrix Mounting Brackets with screws
- 12x Receiver Mounting Brackets with screws (2 per RX)
- 1x Quickstart Guide (this document)
Important! Installation Requirements
- Visit the product page to download the latest firmware, document version, additional documentation, and configuration tools.
- Read through the Wiring and Connections section for important wiring guidelines before creating or choosing premade cables.
- While this product supports CEC for the HDMI outputs, WyreStorm cannot guarantee compatibility with all forms of CEC communication.
Basic Wiring Diagram
This section describes the basic wiring setup for the WyreStorm EXP-MX-0808-KIT Matrix Switch. It illustrates connections between sources (Blu-ray Player, Satellite Box), the matrix, receivers, and displays (TV, Projector), as well as control systems and network infrastructure.
Key Components and Connections:
- Sources: Connected via HDMI to the Matrix inputs.
- Matrix (EXP-MX-0808-KIT): The central hub, receiving HDMI and HDBaseT signals. It has multiple HDMI outputs and HDBaseT outputs for receivers.
- Receivers (EXP-MX-KIT-RX): Connected via Cat6a/7 cable to the Matrix HDBaseT outputs and then via HDMI to displays.
- Control: IR Emitters and Receivers connect to the Matrix and Receivers for remote control. RS-232 connections are also available for advanced control systems.
- Network: LAN connection for potential firmware updates or control system integration.
- Power: AC power connection for the Matrix.
Key Legend:
- HDMI: HDMI signal path
- HDBaseT / Ethernet: HDBaseT signal and Ethernet path
- Control: Control signal path (IR, RS-232)
- Power: Power connection
- Digital Audio: Digital audio signal path
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.
IMPORTANT! Wiring Guidelines
- The use of patch panels, wall plates, cable extenders, kinks in cables, and electrical or environmental interference will have an adverse effect on signal transmission which may limit performance. Steps should be taken to minimize or remove these factors completely during installation for best results.
- WyreStorm recommends the use of shielded category cable to minimize signal noise and interference.
- WyreStorm recommends using pre-terminated HDMI cables due to the complexity of these connector types. Using pre-terminated cables will ensure that these connections are accurate and will not interfere with the performance of the product.
Cat6 Cable Performance Guide
The following table outlines the performance of Cat6 cable for different transmission distances and resolutions:
| Distance (m) | Distance (ft) | 4K Transmission | HD Transmission |
|---|---|---|---|
| 0-100m | 0-328ft | Up to 70m/230ft | Up to 100m/328ft |
Note: WyreStorm recommends the use of shielded cable to minimize signal noise and interference.
IR TX/RX Guidelines
- Using WyreStorm infrared emitters and receivers is the best way to ensure that most IR coding formats are transmitted and received by the system.
- Other 3rd party emitters and receivers can be used; however, these devices must operate in the same manner as the WyreStorm devices.
- Due to differences in IR across 3rd party control systems, their IR ports should never be connected directly to a NetworkHD system as an incompatibility may exist. WyreStorm offers a cable that compensates for voltage differences as well as adjusts for differences in the pins used within the port. Refer to the CAB-IR-LINK product page for more information.
IR TX Port Pinout: Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.
- Tip: Anode
- Sleeve: Cathode (IR Signal)
IR RX Port Pinout: Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs +5V DC to power the included IR receiver.
- Tip: +5V DC
- Ring: IR Signal
- Sleeve: Ground (GND)
RS-232 Wiring
Most control systems and computers are DTE where pin 2 is RX; this can vary from device to device. Refer to the documentation for the connected device for pin functionality to ensure that the correct connections can be made.
Matrix RS-232 Port
| WyreStorm Connector | 3rd Party Device |
|---|---|
| Pin 1 TX (Transmit) | → To → RX (Receive) |
| Pin 2 RX (Receive) | → To → TX (Transmit) |
| Pin 3 G (Ground) | → To → G (Ground) |
Receiver (RX) RS-232 Port
| WyreStorm Connector | 3rd Party Device |
|---|---|
| Pin 2 TX (Transmit) | → To → RX (Receive) |
| Pin 3 RX (Receive) | → To → TX (Transmit) |
| Pin 5 G (Ground) | → To → G (Ground) |
Note: Pins not shown in table have no connection.
Audio Wiring
This matrix contains audio connections for S/PDIF digital.
- Tip: Signal (+)
- Shield: Ground/Return (-)
Accessing the Web UI
This matrix is set to a default static IP Address (192.168.11.143). In order to communicate with it initially, the PC must be set to a 192.168.11.xxx address with a subnet of 255.255.0.0. This can be changed back once a static IP is set within a different range.
- Connect the matrix to the same network as a PC.
- Open a web browser and enter the IP Address of the matrix. Default: 192.168.11.143 | Password: admin
IP Address Notes
- When to set to DHCP, the IP address of the unit can be displayed by pressing and holding the front panel Enter and Down buttons for 3 seconds. The IP address will be displayed on the front panel.
- The installer password and general password are the same by default. WyreStorm recommends changing the password for installer login to avoid any unwanted changes being made to the matrix configuration.
Troubleshooting
No or Poor Quality Picture (snow or noisy image)
- Verify that power is being supplied to the transmitter and receiving device.
- Verify that all HDMI and HDBaseT connections are not loose and are functioning properly.
- Verify that the HDBaseT cable is properly terminated following EIA568B standard.
- Verify that the output resolution of the source and display is supported by this matrix and receiver.
- If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.
No or Intermittent 3rd party Device Control
- Verify that the IR and RS-232 cables are properly terminated following the Wiring and Connections section.
✔ Troubleshooting Tips:
WyreStorm recommends using a cable tester or connecting the cable to other devices to verify functionality.
Specifications
Audio and Video
| Matrix | Receivers | |
|---|---|---|
| Inputs | 8x HDMI In: 19-pin type A 8x Optical Audio Out: Toslink Female |
1x HDBT In: 8-pin RJ-45 Female 1x HDMI Out: 19-pin type A |
| Outputs | 6x HDBT Out: 8-pin RJ-45 Female 2x Switched HDMI Out: 19-pin type A |
|
| Output Video Encoding | HDBaseT Class B | |
| Encoding Data Rate | 9.2Gbps | |
| End to End Latency (Max) | 10µs (micro seconds) | |
| Audio Formats | S/PDIF: 2ch LPCM | Dolby Digital/DTS up to 5.1ch HDMI: 2ch LPCM | Multichannel up to Dolby Atmos and DTS-X |
Video Resolutions (Max)
| Video Resolution | HDMI | Cat6 | Cat6a/7 |
|---|---|---|---|
| 1920x1080p @60Hz 12bit | 15m/49ft | 60m/197ft | 70m/230ft |
| 1920x1080p @60Hz 16bit | 7m/23ft | 35m/115ft | 40m/131ft |
| 3840x2160p @24Hz 10bit 4:2:0 HDR | 3m/10ft | 35m/115ft | 40m/131ft |
| 3840x2160p @30Hz 8bit 4:4:4 | 7m/23ft Input 15m/49ft Output |
35m/115ft | 40m/131ft |
| 3840x2160p @60Hz 8bit 4:2:0 | 7m/23ft Input 15m/49ft Output |
35m/115ft | 40m/131ft |
Note: WyreStorm recommends the use of shielded category cable to minimize signal noise and interference.
Supported Standards
DCI (4096x2160) | RGB | HDR | HDR10 | Dolby Vision up to 30Hz | HLG | BT.2020 | BT.2100
Maximum Pixel Clock
HDBaseT: 340MHz
Communication and Control
| Matrix | Receivers | |
|---|---|---|
| HDMI | HDMI 2.0 | HDCP 2.2 | EDID | CEC | DVI/D supported with adapter (not included) | HDMI 2.0 | HDCP 2.2 | EDID | CEC | 1-way PoH | Bidirectional IR |
| HDBaseT | ||
| Consumer Electronics Control (CEC) | CEC power triggering for connected screens - Requires CEC compatibility | |
| IR | 6x IR RX: 3.5mm (1/8in) TRS Stereo 8x IR TX: 3.5mm (1/8in) TS Mono Bidirectional over HDBaseT |
1x IR TX: 3.5mm (1/8in) TS Mono 1x IR RX: 3.5mm (1/8in) TRS Stereo Bidirectional over HDBaseT |
| RS-232 | 1x RS-232: 9-pin DB9 Female (matrix control only) | 1x RS-232: 3-pin Terminal Block - 3.5mm (update only) |
| Ethernet | 1x LAN: 8-pin RJ-45 Female | NA |
Power
| Matrix | Receivers | |
|---|---|---|
| Power Supply | 100~240V AC 50/60Hz | 18V DC (Optional) |
| PoH | 1-way Matrix to Receiver | 4.5W with External PSU 5W via PoH |
| Max Power Consumption | 109.5W with 6 RXs Connected via PoH | 15.4 BTU/hr with External PSU 17 BTU/hr via PoH |
Environmental
| Matrix | Receivers | |
|---|---|---|
| Operating Temperature | 0 to +45°C (32 to +113 °F), 10% to 90%, non-condensing | |
| Storage Temperature | -20 to +70°C (-4 to +158 °F), 10% to 90%, non-condensing | |
| Maximum BTU | 374 BTU/hr |
Dimensions and Weight
| Matrix | Receivers | |
|---|---|---|
| Rack Units/Wall Box | 1U | <1U |
| Height | 43.5mm/1.72in | 15.2mm/0.6in |
| Width | 440mm/17.33in | 136.4mm/5.38in |
| Depth | 300mm/11.82in | 74.2mm/2.93in |
| Weight | 4.06kg/8.93lbs | 0.24kg/0.53lbs |
Regulatory
| Safety and Emission | CE | FCC | RoHS | RCM | EAC |
Note: WyreStorm reserves the right to change product specification, appearance or dimensions of this product at any time without prior notice.
Warranty Information
WyreStorm Technologies LLC warrants that its products to be free from defects in material and workmanship under normal use for a period of five (2) years from the date of purchase. Refer to the Product Warranty page on wyrestorm.com for more details on our limited product warranty.
