INOGENI INO-BUTTON KIT

Dear Customer,

Congratulations on the purchase of your new INOGENI product. This finely engineered solution will definitely elevate any videoconference experience. Take advantage of an entire support team to address any AV challenges you may have.

What is in the Box

• 1x button with assembled cable with screw and nut hardware
• 1x terminal block plug
• 1x Installation Guide
• One terminal block cable. Length options:
  • INO-BUTTON KIT – 4 m (4 meters / 12 ft)
  • INO-BUTTON KIT – 8 m (8 meters / 25 ft)

Typical Application

This section describes typical connection diagrams for the TOGGLE ROOMS or the TOGGLE ROOMS XT for larger spaces, used in a videoconferencing setup with the button embedded on the table.

Diagram Descriptions:

Device Connectors

Illustrates the INO-BUTTON KIT components: a round, black backlit button designed for table mounting via a grommet, labeled "CONNECT LAPTOP & PRESS BUTTON TO HOST THE MEETING". It also shows a green terminal block connector.

Table Top Installation View

A visual representation of the button mounted through a table surface, secured with a grommet.

Connection Diagrams (TOGGLE ROOMS & TOGGLE ROOMS XT)

These diagrams show how the INO-BUTTON KIT connects to INOGENI TOGGLE ROOMS or TOGGLE ROOMS XT devices to enable Bring Your Own Meeting (BYOM) functionality. The button is connected via a CAT cable to the TOGGLE ROOMS/XT system, which interfaces with a Room PC, display, and other AV peripherals like touch panels and speakerphones. The diagrams depict both "Under the table" and "Behind the display" installation scenarios.

LEGEND

Key symbols used in diagrams include USB, HDMI, USB-C, and CAT6A cable extensions, indicating various connection types and cable lengths up to 70 m (230 ft) for CAT6A.

Installation Steps

Before you get started, ensure that all drivers required for USB devices are installed.

What you'll need for the installation:

• INO – BUTTON KIT (includes button with cable, screw/nut hardware, terminal block plug, Installation Guide)
• One terminal block cable (4m or 8m options available)
• INOGENI TOGGLE ROOMS or TOGGLE ROOMS XT
• 57 mm [2 ½ in] hole saw with drilling kit
• Flat screwdriver
• Category (CAT) cable with the required length

Instructions:

1. Drill Hole: Drill a 2½ inch [57 mm] hole into the table using the appropriate hole saw. Mount the button's screw through the table and secure it with the nut underneath, tightening counterclockwise.
2. Connect Cable: Use the included 4-meter (12 ft) or 8-meter (25 ft) terminal block cable, or a CAT cable of appropriate length. Connect the terminal block to the CAT conductors according to the TOGGLE ROOMS GPI connection. A recommended connection uses the T-568B standard with a CAT cable.

   Connection Pinout Table

   This table details the connection between the button and the TOGGLE ROOMS/XT GPI interface:

   Button Connector	TOGGLE ROOMS GPI connector	TOGGLE ROOMS XT GPI connector	CAT signal T-568B	Signal description
   VOUT	VOUT	VOUT	Solid green	+5V voltage supply for LED
   			Solid blue	Ground
   1	1	1	Solid orange	Normally open contact
   N/A	N/A	N/A	N/A	N/A

3. Connect Terminal Blocks: Connect both terminal block connectors to the button cable and the TOGGLE ROOMS or TOGGLE ROOMS XT GPI interface.
4. Verify Connection: Click the button to switch the host connection. The button's LED will light up, indicating that the TOGGLE ROOMS or TOGGLE ROOMS XT has selected the laptop connection.

Button and LED Behavior

When the user presses the button, it triggers the TOGGLE ROOMS or TOGGLE ROOMS XT to change the current mode. The button has an integrated LED that indicates the connection status:

Certification, Compliance and Warranty Information

CE Statement

INOGENI Inc. declares that the INO – BUTTON KIT conforms to European Standards EN 55032, EN 55035, and RoHS Directive 2011/65/EU + 2015/863/EU.

UKCA Statement

This device complies with the Electromagnetic Compatibility Regulations 2016 No. 1091, leading to the UKCA marking.

Learn More and Support

To learn more, visit the product page at: www.inogeni.com/product/ino-button-kit

For technical support, contact us at: support@inogeni.com

INOGENI Contact Information

INOGENI
1045 Wilfrid-Pelletier Avenue
Suite 101
Québec City, QC G1W 0C6, Canada
+1 418 651 3383