Arteconfort UROS Ceiling Fan

CAUTION

• The product must only be installed by an authorized electrician and in compliance with local, regional and state electricity regulations.
• Check if the electrical specifications of this device are compatible with your installation.
• Turn off the power before installing or repairing the fan.
• The fan must be properly grounded to avoid the risk of electric shock.
• Use and unauthorized technical modifications could suppose a risk of injury.
• The fan must be connected to a 230V 50Hz power supply.
• Do not connect the fan motor to a current dimmer. It could give unsatisfactory performance (engine humming) and cause engine damage.
• Be careful while working near the spinning blades.
• Never connect the fan to a power point but to the ceiling itself.
• The fan must be installed so that the blades are at least 2.3 meters above the ground.
• The fan must be hung from a structure capable of supporting a weight of at least 50 kg. The fixture must be able to support the weight of the fan in motion and should not wobble or loosen.
• Make sure that the blades do not come in contact with any object at the installation site. Always leave a minimum clearance of 50cm from the tip of the blades to the wall or ceiling. Keep in mind that the larger this space, the better the fan's air flow will be.
• The fan must not be started in a room with a gas appliance running at the same time.
• This device can be used by children aged 8 years and above and of people with reduced physical, sensory or mental abilities or lack of experience and knowledge if they are supervised or instructed about the use of the device safely and understand the risks involved. As well as cleaning and maintenance of the device.
• Children should not play with the device.
• To reverse the direction of the blades, do it while moving.
• Do not insert any object into the fan blades while they are rotating. This can damage them and alter the balance of the fan and the device can fall down.
• After the fan is fully installed make sure all fasteners are securely fastened to prevent any wobbling or falling of the machine.

BEFORE INSTALLATION

Open the box avoiding the use of blades or "cutters" to avoid scratching the fan components. Unpack the parts handling them carefully so that they do not bend or scratch, and place the motor on a cloth or a soft surface to prevent damage (you can also use the anti-shock foam on the box for this purpose). Never support the motor sideways. It is advisable to mount the fan on the floor or a surface large enough so that no component falls. Identify all parts before beginning assembly.

TOOLS NEEDED

*Not included. It is recommended that the screwdriver be magnetized.

• Step ladder
• Screwdrivers (Phillips and flathead)
• Hammer
• Drill
• Pliers
• Tape measure

INSTALLATION GUIDE

Follow these steps carefully for proper installation:

1. Ensure power is OFF: Turn off the main power supply to the fan using the switch or circuit breaker.
2. Mount the Bracket: Securely attach the ceiling mount bracket to the ceiling joist or a suitable support structure using the provided screws and anchors.
3. Wire the Fan: Connect the fan's wires to the ceiling supply wires. Typically, this involves connecting the live (L), neutral (N), and ground wires. Refer to the specific wiring diagram provided with your fan for correct connections.
4. Attach the Fan Motor Housing: Lift the fan motor housing and attach it to the mounted ceiling bracket. Ensure it is securely fastened.
5. Install the Canopy: Slide the decorative canopy over the mounting bracket and secure it to cover the wiring and mounting hardware.
6. Connect Remote Receiver: If your fan includes a remote control receiver, connect its wires to the fan motor wires and the ceiling supply wires according to the receiver's instructions.
7. Attach Fan Blades: Securely fasten the fan blades to the motor assembly using the provided screws.
8. Prepare Ceiling Mount: Ensure the ceiling mount assembly is correctly prepared.
9. Secure Ceiling Bracket: Double-check that the ceiling bracket is firmly attached to the ceiling.
10. Wiring Connections: Make the final wiring connections at the ceiling box, ensuring correct polarity for live, neutral, and ground.
11. Hang Fan Motor: Hang the fan motor assembly onto the ceiling bracket.
12. Connect Motor to Receiver: Connect the fan motor wires to the corresponding terminals on the remote receiver.
13. Final Wire Connections: Complete all necessary wire connections between the fan, receiver, and ceiling supply.
14. Attach Motor Housing: Securely attach the fan motor housing to the ceiling bracket.
15. Sloping Roof Note: If installing on a sloping roof, it is recommended to remove the magnetized ring.
16. Final Attachment: Ensure all components are securely attached.
17. Restore Power: Turn the main power supply back ON.

REMOTE CONTROL

The remote control allows you to operate the fan's functions conveniently.

Remote Diagram Description:

Functions:

• WINTER/SUMMER MODE: Reverse the direction of rotation of the blades to change to summer mode or winter mode.
• FAN ON/OFF: Turn the fan on or off.
• SPEED REGULATOR: Increases or decreases the turning intensity of the blades.
• SYNCHRONISATION: Refer to the "Synchronisation of the control unit" section for instructions.
• PROGRAMMING: Sets the hours of fan operation (1, 2, 4 or 8 hours).
• BREEZE MODE: Activates the breeze mode that alternates smoothly between soft and fast speeds (from speed 1 to 3) to create a greater sensation of comfort. To activate the breeze mode, activate the fan using the "ON/OFF" button on the fan and then press the "Breeze mode" button. To cancel breeze mode press the "Breeze mode" button again; the fan will return to the rotation speed selected before the breeze mode. You can also press the "ON/OFF" button of the fan to completely stop the rotation of the blades; when you turn it on again it will not remember the breeze mode, activating at the previously selected rotation speed.

REMOTE CONTROL SYNCHRONIZATION

The remote is factory synchronized. You only need to resynchronize the remote if you have lost synchronization, purchased a new one, want to control several fans with a single remote, or the fan does not respond to the remote control orders while it is running.

One Remote to a New Fan:

1. Cut the current: Be sure to cut off the current until the fan stops and wait 30 seconds.
2. Restore the current: After 30 seconds, re-establish the current to the fan.
3. Synchronize the remote: Within 10 seconds, press the synchronization button (?) for 3 seconds until you hear the signal. Control range: 8-10m.

One Remote to Various Fans:

1. Cut the current: Be sure to cut off the current until all fans stop and wait 30 seconds.
2. Restore the current: After 30 seconds, re-establish the current to the fans.
3. Synchronize the remote: Within 10 seconds, press the synchronization button (?) on each fan for 3 seconds until you hear the signal. If they are within a radius of less than 10m (control range: 8-10m), all will synchronize at the same time.

Two Remotes to One Fan:

1. Clear synchronization for Fan A: Cut power to Fan A, wait 30 seconds.
2. Synchronize Fan B: Cut power to Fan B, wait 30 seconds. Restore power to Fan B. Within 10 seconds, press the synchronization button (?) on remote B for 3 seconds until you hear the signal to synchronize remote B with Fan B.
3. Synchronize Fan A: Cut power to Fan B, wait 30 seconds. Restore power to Fan A. Within 10 seconds, press the synchronization button (?) on remote A for 3 seconds until you hear the signal to synchronize remote A with Fan A.
4. Repeat the steps: Repeat the steps for each fan you have and want to individualize its remote control.

*It is not possible to synchronize more than two controllers to one fan.

TROUBLESHOOTING

Before carrying out the checks detailed below, the fan must be without power supply.

1. The fan does not start:

• Replace the remote control batteries if they are exhausted or not suitable.
• Check that there are no nearby devices that may be causing interference with the remote or reducing signal reception.
• Resynchronize the remote control.
• Check that the electrical connections are correct (must be carried out by a licensed electrician).
• Check fuses and switches, that the installation has voltage and it reaches the fan.

2. The fan makes excessive noise while rotating:

• Allow a slight separation between the canopy and the ceiling, preventing them from touching directly.
• Check that the fixing screws of the blades, the fixing screws to the roof, the stem and the fastening elements are correctly tightened.
• If you replaced the original remote control or receiver, reinstall the supplied ones along with the fan.

3. The fan wobbles:

• Check that the fixing screws of the blades, the fixing screws to the roof, the stem and the fastening elements are correctly tightened.
• Check that the blades are not deformed and follow the blade balancing instructions detailed in this manual.

4. The fan does not give air or the air flow is insufficient:

• Check that the blades are not mounted backwards.
• Check that the blades rotate in the correct direction (Summer / Winter).
• Avoid nearby objects that may impede air circulation.
• Verify that the diameter of the blades of your fan is sufficient for the area of the room in which it is installed.

MAINTENANCE

Over time and due to the natural movement of the fan, some connections may come loose. Check the support connections, brackets and attach the blades twice a year, and make sure they are firm. Clean the appliance regularly to maintain its appearance as new. To do this, use a soft, lint-free cloth to avoid scratching the finish. Never use water, because it could damage the motor or the wood of the blades. It is not necessary to grease the fan, since the motor bearings permanently contain lubricant.

WARRANTY

The motor of this fan is guaranteed for 8 years and 3 years for the rest of the components. This warranty covers the exchange or repair of any failure or defect of the device, provided that it is due to a manufacturing fault or a defective component.

IMPORTANT:

It is essential for the use of this guarantee to prove the purchase date of the product. Therefore, it will be necessary to present the purchase receipt as well as this instruction manual.

Conserve el ticket de compra y el manual de instrucciones.

The warranty of this product does not apply if the defects of the device have been caused by:

• Damage during transport not carried out by the manufacturer. (Example: dents, components or glass pieces damages...)
• Carrying out incorrect installations or assemblies.
• Poor preservation of the product.
• Damage caused by contact of the device with chemical or inappropriate substances. This fan is designed for indoor use only, so it should not be exposed to water and / or humidity either.
• The replacement or use of additional parts or accessories that are not original from the manufacturer.
• When using a control through a wall dimmer other than the remote control supplied with the fan.

Before calling for technical assistance, it is advisable to read the troubleshooting guide included in this manual.

ENVIRONMENT

Do not throw electrical appliances into the household waste, use selective collection facilities. Consult local authorities for more information. If electrical appliances are deposited in landfills, hazardous components can seep into groundwater and enter the food chain, damaging health and well-being. Thanks for taking care of the environment.

SPARE PARTS

You can request spare parts by going to the store where you purchased it or to any another of the brand. If the product is under warranty, present the purchase receipt or invoice.

PARTS GUIDE

GENERAL GUIDE: PARTS OF A FAN

• Ceiling mount
• Roof trim
• Magnet cap
• Shank
• Body trim
• Blades
• Motor

SCREW GUIDE

SCREWS FOR THE ROOF:

• Ceiling screws
• Ceiling screw plugs
• Washer for ceiling screw

SCREWS FOR BLADES:

• Screw for wood blades
• Screw for blades with washer
• Screw for blades
• Paper washer for blade screw

CONTACT INFORMATION

If you have any questions, problems or missing components, consult your dealer. You can also contact us through the email info@arteconfort.com or through the contact form available on our website.