Arteconfort OLIVER S Ceiling Fan

Introduction & Safety

Introduction

Please read this instruction manual carefully before beginning installation and save it for future reference. In case of transfer of the device, you must also give this instruction manual to the corresponding person.

General Safety Precautions

When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury.

Installation Safety

• The product must only be installed by an authorized electrician and in compliance with local, regional, and state electricity regulations.
• Check if the electrical specifications of this device are compatible with your installation.
• Turn off the power before installing or repairing the fan.
• The fan must be properly grounded to avoid the risk of electric shock.
• Use and unauthorized technical modifications could suppose a risk of injury or death.
• The fan must be connected to a 230V 50Hz power supply.
• Do not connect the fan motor to a current dimmer. It could give unsatisfactory performance (engine humming) and cause engine damage.
• Be careful while working near the spinning blades.
• Never connect the fan to a power point but to the ceiling itself.
• The fan must be installed so that the blades are at least 2.3 meters above the ground.
• The fan must be hung from a structure capable of supporting a weight of at least 50 kg. The fixture must be able to support the weight of the fan in motion and should not wobble or loosen.
• Make sure that the blades do not come in contact with any object at the installation site. Always leave a minimum clearance of 50cm from the tip of the blades to the wall or ceiling. Keep in mind that the larger this space, the better the fan's air flow will be.
• This device is designed for indoor use only. Do not use in an open space or where it may be exposed to water or moisture.
• Never install the appliance in a room with a high degree of humidity.
• The fan must not be started in a room with a gas appliance running at the same time.

Usage Safety

• This device can be used by children aged 8 years and above and by people with reduced physical, sensory or mental abilities or lack of experience and knowledge if they are supervised or instructed about the use of the device safely and understand the risks involved, as well as cleaning and maintenance of the device.
• Children should not play with the device.
• To reverse the direction of the blades, do it while moving.
• Do not insert any object into the fan blades while they are rotating. This can damage them and alter the balance of the fan, and the device can fall down.
• After the fan is fully installed, make sure all fasteners are securely fastened to prevent any wobbling or falling of the machine.

User Responsibility

The instructions and safety regulations in this manual cannot prevent all conditions and situations that may occur. For obvious reasons, this manual cannot include factors such as caution and care. These factors must be assumed by who installs, maintains, uses, and enjoys the product.

Before Installation & Tools

Before Installation

Open the box avoiding the use of blades or "cutters" to avoid scratching the fan components. Unpack the parts handling them carefully so that they do not bend or scratch, and place the motor on a cloth or a soft surface to prevent damage (you can also use the anti-shock foam on the box for this purpose). Never support the motor sideways. It is advisable to mount the fan on the floor or a surface large enough so that no component falls. Identify all parts before beginning assembly.

Tools Needed (Not Included)

• Screwdriver (magnetized recommended)
• Electric Drill
• Pliers
• Hammer
• Measuring Tape
• Screwdriver Set

Installation Guide

Follow these steps carefully for installation:

1. Power Off: Ensure the main power switch is in the OFF position. ⚠️
2. Assemble Mounting Bracket: Attach the mounting bracket components as shown in the diagram.
3. Connect LED Module: Connect the LED module wiring. Ensure correct polarity and secure connections. ⚠️
4. Attach Fan Body to Bracket: Secure the fan body to the assembled mounting bracket.
5. Connect Wiring: Connect the fan's internal wiring to the ceiling supply wires. Ensure all connections are secure and correct (Live, Neutral, Earth).
6. Attach Canopy: Slide the canopy up to cover the wiring and mounting bracket.
7. Secure Mounting Bracket to Ceiling: Mount the bracket to the ceiling using appropriate screws and wall plugs. Ensure it is firmly attached.
8. Insert Wall Plugs: If mounting into drywall or plaster, insert wall plugs for secure fastening.
9. Screw Mounting Bracket: Fasten the mounting bracket securely to the ceiling structure.
10. Wiring Terminal Block: Connect the ceiling supply wires (L - Live, N - Neutral, Earth) to the corresponding terminals in the fan's junction box.
11. Connect Wires to Terminal Block: Ensure all wire connections are properly seated and secured within the terminal block.
12. Connect Fan Wires: Connect the fan's wiring harness to the ceiling supply wires.
13. Connect LED Module Wires: Connect the LED module's wiring. Pay close attention to connector types and any warning symbols (⚠️) indicating correct orientation and secure fit.
14. Attach Fan Body: Secure the fan body to the mounting bracket.
15. Attach Blades: Screw the fan blades onto the motor arms. Ensure they are correctly oriented.
16. Secure Blades: Tighten the blade screws firmly.
17. Attach Light Cover: Install the light cover or diffuser.
18. Final Assembly: The fan is now fully assembled.
19. Power On: Turn the main power switch to the ON position. ⚠️

Troubleshooting

Ensure the fan is without power before performing any checks.

Fan Does Not Start

1. Replace the remote control batteries if they are exhausted or not suitable.
2. Check that there are no nearby devices that may be causing interference with the remote or reducing signal reception.
3. Resynchronize the remote control.
4. Check that the electrical connections are correct (must be carried out by a licensed electrician).
5. Check fuses and switches, that the installation has voltage and it reaches the fan.

Fan Does Not Start, Light Does

With the fan off, check with your hand that the blades turn freely.

Excessive Noise While Rotating

1. Allow a slight separation between the canopy and the ceiling, preventing them from touching directly.
2. Check that the fixing screws of the blades, the fixing screws to the roof, the stem and the fastening elements are correctly tightened.
3. If you replaced the original remote control or receiver, reinstall the supplied ones along with the fan.

Fan Wobbles

1. Check that the fixing screws of the blades, the fixing screws to the roof, the stem and the fastening elements are correctly tightened.
2. Check that the blades are not deformed and follow the blade balancing instructions detailed in this manual.

No Airflow or Insufficient Airflow

1. Check that the blades are not mounted backwards.
2. Check that the blades rotate in the correct direction (Summer/Winter).
3. Avoid nearby objects that may impede air circulation.
4. Verify that the diameter of the blades of your fan is sufficient for the area of the room in which it is installed.

Light Does Not Turn On

1. Check the bulb is not blown, otherwise replace it with a new one.
2. If your fan has LED light included, check the connections are properly fixed according to the instruction manual.

Remote Control

Functions

The remote control operates various functions of the fan:

• Winter/Summer Mode: Reverses the direction of rotation of the blades.
• ON/OFF Light / Synchronization: Turns the light and synchronization on or off.
• ON/OFF Fan: Turns the fan on or off.
• Speed Regulator: Increases or decreases the turning intensity of the blades.
• Light Intensity Regulator: Increases or decreases the intensity of the light.
• LCD Indicator: Shows the number of speeds.
• Light Temperature: Changes the color temperature of the light.
• Programming: Sets the hours of fan operation (1, 2, or 4 hours).
• Breeze Mode: Activates a mode that alternates smoothly between soft and fast speeds (from speed 1 to 3) to create a greater sensation of comfort. To activate, turn the fan on, then press the "Breeze mode" button. To cancel, press the "Breeze mode" button again, or turn the fan off and on.

Color Temperature Memory

The fan has color temperature memory. This function allows you to maintain the same color temperature when the fan light is turned on again. To change the color temperature, press the button indicated with the color of each temperature. When you turn the light off and on again, it will keep the selected temperature.

Batteries

The remote control batteries are not included. The required battery model is 2x AAA. Remove the batteries from the controller if it is not going to be used for a long time.

Remote Control Synchronization

General Notes

The remote is factory synchronized. You only need to resynchronize the remote if you have lost synchronization, purchased a new one, want to control several fans with a single remote, or the fan does not respond to the remote control orders while it is running.

One Remote to One Fan

1. Cut the current: Be sure to cut off the current until the fan stops and wait 30 seconds. ⚡
2. Restore the current: After 30 seconds, re-establish the current.
3. Synchronize the remote: Within 10 seconds, press the "ON/OFF light" button for 3 seconds until you hear the signal and the light flashes. Control range: 8-10m.

One Remote to Multiple Fans

1. Cut the current: Be sure to cut off the current until all fans stop and wait 30 seconds. ⚡
2. Restore the current: After 30 seconds, re-establish the current.
3. Synchronize the remote: Within 10 seconds, press the "ON/OFF light" button on each fan for 3 seconds until you hear the signal and the light flashes. If they are within a radius of less than 10m, all will synchronize at the same time.

Two Remotes to One Fan

This procedure allows you to synchronize two different remotes (A and B) to a single fan.

1. Cut power to Fan A: Be sure to cut the power to Fan A (the one you want to remove synchronization from) and wait 30 seconds. ⚡
2. Cut power to Fan B: Be sure to cut the power to Fan B (the one you want to synchronize) and wait 30 seconds. ⚡
3. Restore power to Fan B: When you restore power to Fan B and within 10 seconds, press the "ON/OFF light" button for 3 seconds until you hear the signal and the light flashes to synchronize remote B with Fan B.
4. Cut power to Fan B: Be sure to cut the power to Fan B and wait 30 seconds. ⚡
5. Restore power to Fan A: When you restore power to Fan A and within 10 seconds, press the "ON/OFF light" button for 3 seconds until you hear the signal and the light flashes to synchronize remote A with Fan A.
6. Repeat steps: Repeat the steps with each fan you have and want to individualize its remote control.

*To cut the current, you can press the individual fan switch. If there is not, disconnect the quick connect cables from the fan.

Note: It is not possible to synchronize more than two controllers to one fan.

Parts Identification

This diagram identifies the main components of the ceiling fan:

• Ceiling Mount / Soporte de techo: The fixture that attaches to the ceiling.
• Roof Trim / Florón: Covers the ceiling mount.
• Trim / Embellecedor: Decorative trim piece.
• Motor: The main unit housing the motor.
• Blades / Aspas: The fan blades that move air.
• Body Trim / Embellecedor de cuerpo: Decorative trim around the motor housing.
• LED Module / Módulo led: The integrated light source.
• Led Plate / Plato led: The plate holding the LED module.
• Ceiling / Plafón: The top part of the fan assembly that attaches to the ceiling.

Screw Guide

This guide illustrates the types of screws used for installation:

Screws for the Roof / Tornillos para Techo

• Standard Screws: For direct mounting into ceiling joists or suitable anchors.
• Ceiling Screw Plugs / Tacos: Wall plugs for use in drywall or plaster.
• Washer for Ceiling Screw / Arandela: Used with ceiling screws for better load distribution.

Screws for Blades / Tornillos para Aspas

• Screw for wood blades: Standard screws for attaching wooden blades.
• Screw for blades with washer: Screws with integrated washers for blade attachment.
• Screw for blades: Standard screws for blade attachment.
• Paper washer for blade screw / Arandela de papel: Thin washers, possibly for balancing or specific blade mounting.

Spare Parts

You can request spare parts by going to the store where you purchased it or to any another of the brand. If the product is under warranty, present the purchase receipt or invoice.

Warranty Information

Coverage

The motor of this fan is guaranteed for 8 years and 3 years for the rest of the components. This warranty covers the exchange or repair of any failure or defect of the device, provided that it is due to a manufacturing fault or a defective component.

Important Notes

It is essential for the use of this guarantee to prove the purchase date of the product. Therefore, it will be necessary to present the purchase receipt or invoice, as well as this instruction manual. ⚠️ Keep the purchase receipt and the instruction manual.

Warranty Exclusions

The warranty of this product does not apply if the defects of the device have been caused by:

• Damage during transport not carried out by the manufacturer (e.g., dents, components or glass pieces damages...).
• Carrying out incorrect installations or assemblies.
• Poor preservation of the product.
• Damage caused by contact of the device with chemical or inappropriate substances. This fan is designed for indoor use only, so it should not be exposed to water and / or humidity either.
• The replacement or use of additional parts or accessories that are not original from the manufacturer.
• When using a control through a wall dimmer other than the remote control supplied with the fan.

Before Calling for Service

Before calling for technical assistance, it is advisable to read the troubleshooting guide included in this manual.

Contact Information

If you have any questions, problems or missing components, consult your dealer. You can also contact us through the email info@arteconfort.com or through the contact form available on our website.