Aerpro Advanced Safety Vision Systems
Model: AVM10E 10" IP69K Heavy Duty AHD Quad View Monitor
Document Type: User Manual
Introduction
The Aerpro AVM10E is a 10-inch IP69K Heavy Duty AHD Quad View Monitor designed for advanced vehicle safety vision systems. It offers robust performance in harsh environments and provides clear visibility of multiple camera feeds.
WARNINGS
Before using this product, please read this instruction carefully. Take special care to follow the warnings indicated on the unit itself as well as the safety suggestions listed. Keep this user manual for future reference.
Document Date: 16-05-2025
The front of the Aerpro AVM10E monitor is shown, displaying a split screen with four live camera feeds of heavy machinery in operation. The monitor features physical buttons below the screen for control.
Important Notes
- Do not attempt to open the covers.
- Please disconnect the power if anomalies occur.
- Do not use organic solvents on the surfaces to avoid damage to the coating.
- Do not apply force to the wiring leads to avoid internal damage.
- Keep the product away from high dirt/dust environments, direct high temperature sunlight, and high humidity conditions.
- Install the product securely so that it does not fall down.
- Follow the wiring diagram strictly, or the warranty will be voided and can result in damage to the vehicle's electrical system.
- Do not change functions while driving.
- Comply with the operating temperature of this unit.
The vehicle safety vision system is designed to be used with, not instead of, other viewing aids in your vehicle. The manufacturer shall not be held liable for any accidents which occurred while operating this system.
Working Voltage
Please notice the following data for power supply input to the monitor and camera:
- Monitor: Voltage range 10V-32V
Note: If the power exceeds 36V to the monitor, it will cause damage. ⚠️
Operation and Settings
Keystroke Instruction
POWER: Screen ON/OFF
Press the power button on the monitor screen to turn on; press again to turn off.
Camera Selection & Navigation:
[CAM1/< Button]: Selects Camera view AHD1 in the menu interface, or selects decrease function.[CAM2/> Button]: Selects Camera view AHD2 in the menu interface, or selects increase function.[CAM3/v Button]: Selects Camera view AHD3 in the menu interface, or selects secondary menu.[CAM4/^ Button]: Selects Camera view AHD4 in the menu interface, or selects secondary menu.
Split Display Interface: [Icon representing split display]
Enter the menu interface. In the menu interface, press [CAM3/v Button] or [CAM4/^ Button] to select the Picture function, Settings, or System menu interface, and press [Menu Button] to exit the menu.
MENU: Screen
Press [Menu Button]; the monitor will enter the menu setting. In the menu interface, press [CAM3/v Button] or [CAM4/^ Button] to select the Picture, Function, Settings, or System interface.
Press [CAM2/> Button] to enter the Picture function.
Press [CAM3/v Button] or [CAM4/^ Button] to select Brightness, Contrast, Color, and Rest functions.
Picture Settings
Brightness: Press [CAM2/> Button] to enter the brightness function. When in the Brightness function, press [CAM3/v Button] or [CAM4/^ Button] to select AHD1, AHD2, AHD3, or AHD4.
| Camera | Brightness Value |
|---|---|
| AHD1 | 50 |
| AHD2 | 50 |
| AHD3 | 50 |
| AHD4 | 50 |
Press [CAM2/> Button] to increase the brightness and [CAM1/< Button] to decrease the brightness.
Press [Menu Button] to go back to the previous menu.
Contrast: When you enter the contrast function, press [CAM3/v Button] or [CAM4/^ Button] to select AHD1, AHD2, AHD3, or AHD4.
| Camera | Contrast Value |
|---|---|
| AHD1 | 50 |
| AHD2 | 50 |
| AHD3 | 50 |
| AHD4 | 50 |
Press [CAM2/> Button] to increase the contrast and [CAM1/< Button] to decrease the contrast.
Press [Menu Button] to go back to the previous menu.
Color: When you enter the color function, press [CAM3/v Button] or [CAM4/^ Button] to select AHD1, AHD2, AHD3, or AHD4.
| Camera | Color Value |
|---|---|
| AHD1 | 50 |
| AHD2 | 50 |
| AHD3 | 50 |
| AHD4 | 50 |
Press [CAM2/> Button] to increase the color saturation and [CAM1/< Button] to decrease the color saturation.
Press [Menu Button] to go back to the previous menu.
Reset: Resets the system settings to default.
Press [Menu Button] to exit the picture function and press [CAM4/^ Button] to select the next function.
Function Settings
Press [CAM2/> Button] to enter the function menu. Press [CAM3/v Button] or [CAM4/^ Button] to select the desired function: Mirror Flip, Trigger Delay, Video List, Light, VCOM.
| Function | Options |
|---|---|
| Mirror Flip | On / Off |
| Trigger Delay | 00s - 01s (for Multichannel) |
| Video List | Navigate through camera videos |
| Light | On / Off |
| VCOM | Adjustable value (e.g., 80) |
Mirror Flip: When in Mirror Flip function, press [CAM4/^ Button] to select AHD1, AHD2, AHD3, or AHD4. Press [CAM1/< Button] or [CAM2/> Button] to select On or Off.
| Camera | Mirror Flip Status |
|---|---|
| AHD1 | Off |
| AHD2 | Off |
| AHD3 | Off |
| AHD4 | Off |
Press [Menu Button] to go back to the previous menu.
Trigger Delay: When in Trigger delay function, press [CAM4/^ Button] to select AHD1, AHD2, AHD3, AHD4, and Multichannel.
| Channel | Trigger Delay Time |
|---|---|
| AHD1 | 00s |
| AHD2 | 00s |
| AHD3 | 00s |
| AHD4 | 00s |
| Multichannel | 01s |
Press [CAM2/> Button] to increase time and [CAM1/< Button] to decrease time.
Press [Menu Button] to go back to the previous menu.
Video List: When in Video List function, press [CAM4/^ Button] to select AHD1, AHD2, AHD3, or AHD4 videos. Press [CAM3/v Button] to go to the next page and [CAM4/^ Button] to select the next video.
Press [Menu Button] to go back to the previous menu.
Light: When in Light function, press [CAM2/> Button] to select light On and Off.
Press [Menu Button] to go back to the previous menu.
VCOM: When in VCOM function, press [CAM2/> Button] to increase VCOM value and press [CAM1/< Button] to decrease VCOM value.
Press [Menu Button] to go back to the previous menu.
Bracket Installation
Included:
- U-Bracket Installation: Fix the U-bracket into position, insert and lock the monitor into the bracket using the mounting gimbal knobs.
Diagram 1: Shows a U-shaped metal bracket being positioned and secured to a flat surface using screws.
Diagram 2: Illustrates the monitor being attached to the mounted U-bracket. Arrows point to gimbal knobs, indicating their role in adjusting the monitor's angle.
- Adjust a suitable angle:
Diagram 3: Depicts the monitor fully installed and secured on its U-bracket mount on a flat surface.
Diagram 4: Close-up views of the monitor's mounting bracket, highlighting the gimbal knobs that allow for precise adjustment of the monitor's tilt and swivel angles.
Wiring Diagram
The wiring diagram shows the connections for the Aerpro AVM10E monitor. The monitor connects via a multi-pin cable to a central junction. This junction then splits into four separate camera input cables (CAM1, CAM2, CAM3, CAM4). Each camera input is labeled with pins for DC power (CAM-DC), Video (CAM-VIDEO), Audio (CAM-AUDIO), and Ground (GND). The main power harness includes connections for ACC+ (Red wire), Ground (Black wire), and four Trigger wires (Brown, Green, Blue, Gray) corresponding to each camera channel, allowing for camera switching based on triggers.
Specifications
- Display: 10.1" IPS Display
- Resolution: 1024 x 600
- Cameras: Wired (Supports 720p and 1080p AHD Cameras)
- Smartphone Connection: Wireless (Supports Apple CarPlay, Android Auto)
- Audio Output: Bluetooth, FM Transmitter, Built-in Speaker
- Video System: PAL/NTSC Selectable
- Video Inputs: 4
- Video Triggers: 4 (CH1 Priority)
- Display Modes: Single, Dual, Quad (Various)
- Monitor View: Normal / Reverse
- Guidelines: Selectable On/Off (CH2 Only)
- Audio: Onboard Speaker
- Luminance: 600cd/M2
- Power Supply: 11-36V (Hardwired)
- Dimensions (WxHxD): Monitor: 275 x 203 x 53mm (Excluding Mount)
Inclusions:
- 10.1" IPS monitor AVM10E
- 1 x Monitor Mount
- 1 x 1.5m Monitor Cable
- 1 x 1 Sunshade
Additional Information:
- This is a monitor only; cameras are sold separately.
- This monitor accepts SD, HD, and AHD cameras, but they must be consistent. You cannot use a combination of SD and AHD cameras.
Technical Assistance
If you need assistance setting up or using your Aerpro product now or in the future, call Aerpro Support. Australia.
- TEL: 03-8587 8898
- FAX: 03 – 8587 8866
- Hours: Mon-Fri 9am – 5pm AEST
- EMAIL: service@tdj.com.au
If you would like to download a digital copy of this manual, or other Aerpro manuals/software, please visit the Aerpro.com website and search for the product model number for more information, accessories, and products.
This manual is considered correct at the time of printing but is subject to change. For the latest manuals and updates, refer to the website.
Copyright © 2025 by TDJ Australia. All rights reserved. No part of this publication may be reproduced, distributed, or transmitted in any form or by any means, including photocopying, recording, copying, or other electronic or mechanical methods, without the prior written permission of the author.
Note: Additional cameras and wiring may be required depending on your application. Compatible products are available on our website. For more information, visit AERPRO.COM.
Home | Aerpro
