Arcade1Up Street Fighter II Big Blue Owners Manual

Model: SFBB, 2APXHSFBB

Manufacturer: TASTEMAKERS LLC

Important Safety Information

WARNING: TO ENJOY A SAFE GAMING ENVIRONMENT

Please use the wall anchor kit that is included with the product. Make sure to locate your Arcade1UP on a flat surface.

WARNING: Arcade1UP assumes no liability for improper installation or excessive loads placed on screws or bracket.

This wall anchor is not a substitute for proper adult supervision.

WARNING: Serious or fatal crushing injuries can occur from furniture tip-over.

To help prevent tip-over:

Set up Arcade1UP on a level floor.
Never allow children to climb or hang on product.
Always set up an anti-tip device!

Use of tip-over restraints may only reduce, but not eliminate, the risk of tip-over.

WARNING THE EPILEPSY

A very small percentage of individuals may experience epileptic seizures or blackouts when exposed to certain light patterns or flashing lights. Exposure to certain patterns or backgrounds on a television screen or when playing video games may trigger epileptic seizures or blackouts in these individuals. To reduce the risk of such a seizure incident, it is recommended to take a 10-15 minute break at each hour of playing.

READ BEFORE USING THE Arcade1UP SAFETY PRECAUTIONS

Please read and comprehend all warnings stated in this manual.
Do not get arcade wet when cleaning.
Parents and guardians: Please read entire manual before allowing gamer to play.
The AC/DC adapter and apparatus shall not be exposed to dripping or splashing and that no object filled with liquids, such as vases, shall be placed on apparatus.
The AC/DC adapter is used as disconnect device. The AC/DC adapter of apparatus should not be obstructed OR should be easily accessed during intended used. To be completely disconnect the power input, the AC/DC adapter of apparatus shall be disconnected from the mains.
If appliance is provided with protective earth terminal, it should be connected to main outlet with a protective earth connection.
Minimum distances 10 cm / 3.94 inches around the apparatus for sufficient ventilation.
The ventilation should not be impeded by covering the ventilation openings with items such as newspaper, table-cloths, curtains etc.
No naked flame sources such as lighted candles should be placed on the apparatus.
The apparatus should only be used in moderate climates.

FCC STATEMENT

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio / TV technician for help.

Product Overview

This Arcade1Up cabinet features multiple classic games including Street Fighter II titles, Atari, Midway, and Bandai Namco games.

Games Included:

Street Fighter II' Champion Edition
Super Street Fighter II Turbo
Street Fighter II' Hyper Fighting
Darkstalkers: The Night Warriors
Vampire Savior: The Lord of Vampire
Night Warriors
Capcom Sports Club
Muscle Bomber Duo
Saturday Night Slam Masters
Knights of the Round
Super Puzzle Fighter II: Turbo
Eco Fighters
Tempest
Pac-Man

Collect Them All:

ATARI LEGACY LIGHT UP MARQUEE + RISER
CAPCOM LEGACY LIGHT UP MARQUEE + RISER
MIDWAY LEGACY LIGHT UP MARQUEE + RISER
BANDAI NAMCO Entertainment LEGACY LIGHT UP MARQUEE + RISER

Game Controls

General Controls:

MOVE JOYSTICK TO SCROLL THROUGH GAME LIST
PRESS THE A BUTTON TO CHOOSE GAME
HOLD PLAYER 1 (5 SECONDS) TO RETURN TO MENU
HOLD PLAYER 2 (5 SECONDS) TO RESET GAME

Specific Game Controls:

Game	Button 1	Button 2	Button 3	Button 4	Button 5	Button 6
DUNK STARS	SHOT/JUMP	DASH	PASS/TACKLE	KICK
SMASH TENNIS	POWER SHOT	LOB	LIGHT SHOT	ROTATE
STREET FIGHTER™ II CHAMPIONSHIP EDITION	A / JAB PUNCH	B / STRONG PUNCH	SHORT KICK	FORWARD KICK	ROUNDHOUSE KICK
SUPER STREET FIGHTER™ II TURBO	JAB PUNCH	FIERCE PUNCH	SHORT KICK	FORWARD KICK	ROUNDHOUSE KICK
STREET FIGHTER™ II' HYPER FIGHTING	JAB PUNCH	STRONG PUNCH	SHORT KICK	FORWARD KICK	ROUNDHOUSE KICK
DARKSTALKERS™: THE NIGHT WARRIORS	ATTACK	JUMP	PIN ATTACK	GRAB	AIM	FIRE
VAMPIRE SAVIOR: THE LORD OF VAMPIRE	ATTACK	JUMP	GRAB ATTACK	ATTACK	AIM	FIRE
NIGHT WARRIORS™	ATTACK	JUMP	GRAB ATTACK	ATTACK	AIM	FIRE
CAPCOM SPORTS CLUB™	ATTACK	JUMP	DESPERATION JUMP ATTACK	ATTACK
MUSCLE BOMBER DUO	ATTACK	JUMP	ATTACK
SATURDAY NIGHT SLAM MASTERS™	ATTACK	JUMP/SLIDE	PASS/TACKLE
KNIGHTS OF THE ROUND™	ATTACK	JUMP/SLIDE	PASS/TACKLE
SUPER PUZZLE FIGHTER II: TURBO™	SELECT
ECO FIGHTERS™	ATTACK	JUMP

Game Settings

To access game settings, press the PLAYER 2 button when prompted.

Settings Options:

Difficulty (e.g., Easy, Normal, Medium, Hard)
Timer (e.g., On, Off)
Demo Sound (e.g., On, Off)
Speed (e.g., Normal, Fastest)
Save & Exit: Saves current settings and returns to the game menu.
Reset To Defaults: Resets all settings to their original factory state.

Example Settings Screens:

(Note: Visual representations of settings screens are described textually here.)

Street Fighter II Champion Edition Settings: Difficulty: Easy, Timer: Normal, Demo Sound: ON

Capcom Sports Club Settings: Difficulty: Normal, Demo Sound: ON

Muscle Bomber Duo Settings: Difficulty: Normal, Demo Sound: ON

Saturday Night Slam Masters Settings: Difficulty: 1 Normal, Difficulty 2: 2, Demo Sound: ON

Knights of the Round Settings: Difficulty: Normal, Demo Sound: ON

Super Puzzle Fighter II: Turbo Settings: Difficulty: Medium, Demo Sound: ON, Speed: NORMAL

Eco Fighters Settings: Difficulty: 5, Demo Sound: OFF

Street Fighter II' Champion Edition Settings: Difficulty: Easy, Demo Sound: ON, Speed: NORMAL

Super Street Fighter II Turbo Settings: Difficulty: Normal, Demo Sound: ON, Speed: NORMAL

Darkstalkers: The Night Warriors Settings: Difficulty: Normal, Demo Sound: OFF, Speed: FASTEST

Vampire Savior: The Lord of Vampire Settings: Difficulty: Normal, Demo Sound: ON

Night Warriors: Street Fighter II' Hyper Fighting Settings: Difficulty: 2, Demo Sound: OFF, Speed: NORMAL

Troubleshooting

Problem	Possible Cause	Solution
Marquee / Light Up Deck Protector will not light up.	Power cord not plugged into wall outlet. Wires/Plugs improperly connected. Marquee / Deck Protector power cord not plugged in at the back of the monitor. Marquee / Deck Protector power cord plugged into the wrong input.	Make sure power cord is plugged into the wall outlet and there is power to that outlet. Make sure all Wires/Plugs are properly connected and fully inserted as directed in assembly instructions. Turn the ON/OFF switch OFF and then back ON again. You may need to RESET the game. Turn the ON/OFF switch to OFF, unplug the game from the wall outlet, wait 60 seconds, plug it back in, and turn the ON/OFF switch back to ON.
Game will not turn on.	Power cord not plugged into wall outlet. Wires/Plugs improperly connected. ON/OFF Switch is in the OFF position. Upload switch on back of monitor is in the OFF position.	Make sure power cord is plugged into the wall outlet and there is power to that outlet. Make sure all Wires/Plugs are properly connected and fully inserted as directed in assembly instructions. Turn the ON/OFF switch ON. Slide upload switch on back of monitor to the ON position.
Game will turn ON, but there is no sound.	Wires/Plugs improperly connected. Volume Switch is in the OFF position.	Make sure all Wires/Plugs are properly connected and fully inserted as directed in assembly instructions. Slide Volume Switch located on control deck to the right.
You hear sound but there is no picture.	Wires/Plugs improperly connected.	Make sure all Wires/Plugs are properly connected and fully inserted as directed in assembly instructions.
One of the buttons on the control deck is stuck in the down position.	Debris may have gotten between the button and the button housing.	Take something thin (like a business card) and place it between the button and the button housing and slide it back and forth to loosen the debris.
You are not able to scroll through the games on the game selection menu.	You may be using the wrong joystick or pressing the incorrect buttons to scroll through the games.	Look at the game control section in the instruction manual to make sure you are using the correct joystick or pressing the correct buttons to scroll through the game selection menu.
You are able to scroll through the games on the game selection menu, but you can’t enter a game to begin playing.	You may be pressing the wrong button to enter the game.	Look at the game control section in the instruction manual to make sure you are pressing the correct button to enter the game.
You have entered the game, but you can’t get the game to start.	You may be pressing the wrong button to start the game.	Look at the game control section in the instruction manual to make sure you are pressing the correct button to start the game.
You have entered the game, but you can’t exit the game to get back to game selection menu.	You may not be holding down the exit button long enough.	Make sure you are holding the exit button down for 5 seconds to exit the game.
The control functions that are printed on the control deck do not match the gameplay on the screen for the game you are playing.	You may be pressing the wrong game control buttons for that game. The game may only be a 1 or 2 player game.	Look at the game control section in the instruction manual to make sure you are pressing the correct game control buttons for that game. Refer to the game control section in the instruction manual to see how many players are able to play that game.
The game will not let me select 2 or 3 players for a chosen game.	The game may only be a 1 or 2 player game.	Refer to the game control section in the instruction manual to see how many players are able to play that game.
The game screen looks pixelated or there are lines running through the image.	Wires/Plugs were hooked up incorrectly.	Make sure all Wires/Plugs are properly connected and fully inserted as directed in assembly instructions.
The game screen is frozen.	The game encountered a problem when processing the data.	You may need to RESET the game. Turn the ON/OFF switch to OFF, unplug the game from the wall outlet, wait 60 seconds, plug it back in, and turn the ON/OFF switch back to ON.

Specifications

POWER SUPPLY: AC/DC Adapter
INPUT POWER: AC 100-240V~50/60Hz 1.2A Max
OUTPUT POWER: DC12V --- 3A
MONITOR: 17” LCD
CABINET ASSEMBLED DIMENSIONS (WITHOUT RISER): 55.2” x 19” x 22.75” (140.20cm x 48.26cm x 57.78cm)

Adapter Manufacturer: Blue Iron Holdings Ltd.

Adapter Model: BI36-120300-U2

Assistance or Service

Before contacting for assistance or service, please check the "Troubleshooting" section in the User Manual.

If you still have questions regarding your Arcade1Up product or require technical support, contact Arcade1Up Customer Service at www.Arcade1Up.com and click on "Support".

Installation Notes

This game is designed for indoor and personal use only. It must not be installed outdoors.

The following conditions must be avoided:

Direct exposure to sunlight, high humidity, direct water contact, dust, high heat, or extreme cold.
Vibration. The game must be installed on a level surface.

Do not install in an area such that the game would present an obstacle in case of an emergency (i.e., near fire equipment or emergency exits).

IMPORTANT SAFETY INSTRUCTIONS

Read these Instructions.
Keep these Instructions.
Heed all Warnings.
Follow all instructions.
Do not use this apparatus near water.
Clean only with a dry cloth.
Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. When the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
Only use attachments/accessories specified by the manufacturer.
Unplug this apparatus during lightning storms or when unused for long periods of time.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Use only with a riser specified by the manufacturer, or sold with the apparatus. When a riser is used, use caution when moving the riser/apparatus combination to avoid injury from tip-over.
The equipment shall be used at working ambient temperature 32° - 95°F (0° - 35°C).
TIP OVER HAZARD - This apparatus should be secured in place by using the provided mounting means. Free standing is capable of resulting in instability causing possible injury. Refer to the installation instruction for detail.

General Precautions

CAUTION: Servicing instructions are for use by qualified service personnel only. To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.

ALL PICTURES SHOWN ARE FOR ILLUSTRATION PURPOSE ONLY. ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENT.

NOTE: Arcade may take 10-15 seconds to power on after switching on.

Models: SFBB, 2APXHSFBB, SFBB Street Fighter II Big Blue, Street Fighter II Big Blue, Big Blue

File Info : application/pdf, 1 Pages, 1.77MB

SFBB-Users-Manual-WF-TASTEMAKERS-TRADING-2apxhsfbb-ex-1-10 Adobe PDF library 15.00 Adobe Illustrator 25.3 (Windows)

	Arcade1Up Terminator 2 Owners Manual: Setup, Safety, and Troubleshooting Guide Official owner's manual for the Arcade1Up Terminator 2 arcade machine (Model TER-A-10159). Provides essential safety precautions, setup guidance, troubleshooting steps, game settings, control explanations, and technical specifications.
	Arcade1Up Pong Owners Manual: Setup, Troubleshooting, and Game Controls Comprehensive owners manual for the Arcade1Up Pong arcade game table, covering setup, safety precautions, troubleshooting common issues, game controls, and specifications. Learn how to operate and maintain your Arcade1Up Pong unit.
	Arcade1Up Marvel vs. Capcom Owner's Manual Comprehensive owner's manual for the Arcade1Up Marvel vs. Capcom arcade machine, providing setup, operation, troubleshooting, and safety guidelines in English, French, and Spanish.
	Arcade1Up The Simpsons Owners Manual: Safety, Setup, and Troubleshooting Comprehensive owners manual for the Arcade1Up The Simpsons arcade machine. Includes essential safety precautions, setup guidelines, troubleshooting tips, game controls, and technical specifications for an optimal gaming experience.
	Arcade1Up Class of 81 Owner's Manual - MSP-A-10171 Comprehensive owner's manual for the Arcade1Up Class of 81 (MSP-A-10171) featuring safety instructions, troubleshooting, game settings, and control layouts for classic arcade games.
	Arcade1UP Capcom Legacy User Manual User manual for the Arcade1UP Capcom Legacy arcade machine, providing setup, safety, and troubleshooting information.
	Arcade1Up TRON Owner's Manual This owner's manual provides instructions and troubleshooting tips for the Arcade1Up TRON arcade machine. It covers safety precautions, game settings, controls, and assistance information.
	NFL Blitz Arcade1Up Owner's Manual Comprehensive owner's manual for the NFL Blitz Arcade1Up, covering safety precautions, troubleshooting, game settings, and controls. Learn how to set up and operate your Arcade1Up.