Tuya Smart Video Doorbell Quick Start Guideline

Packing List

After opening the package, please make sure the doorbell (referred to as the "Equipment") is in good condition. Make sure all parts below are included:

• Outdoor unit (main doorbell unit)
• Indoor unit (indoor host with display)
• Viscose foam
• Steel sheet hanging board
• Fixing screws

Visual Description: An image shows the outdoor unit (a rectangular device with a camera lens) and the indoor unit (a tablet-like device with a screen). Below the indoor unit, there's a diagram showing its components: a peephole, a plug cable, and hanging screws.

Appearance Introduction

Outdoor Unit Components:

• Light Sensor
• IR LED
• Microphone
• Doorbell Button
• PIR (Passive Infrared Sensor)
• Speaker
• Camera

Indoor Unit Components:

• Display
• Home Button

Indoor Unit Bottom View:

• TF card slot
• Switch
• Charging plug

Visual Description: Diagrams illustrate the front view of the outdoor unit, labeling its various sensors and buttons. Another diagram shows the front view of the indoor unit, highlighting its display and home button. A third diagram shows the bottom of the indoor unit, indicating the TF card slot, switch, and charging plug.

Component Functions

• IR LED: When ambient light is not enough, this can increase picture brightness.
• Light sensor: Used to collect environmental light status. When ambient light drops down to 2 Lux, the IR LED will turn on automatically.
• MIC: Audio Capture.
• Button: Doorbell button.
• PIR: When object movement is detected in front of the device, the device will send notification to your phone automatically.
• Camera: Video image capture.
• Indicator Light:
  • Blinking blue light: Configuration status
  • Red light on: Charging the battery
  • Blue light on: Connected to phone successfully
• Home Button: To reset the device, long press this button for 5 seconds. To light the display, short press this button for 1 second.
• Battery Slot: Supports 1*5000 battery.
• USB Interface: Micro USB port charging.
• Mounting Port: Use this port to mount the camera to a bracket.

Setup the Device

Thank you for choosing our products! Please follow the instructions below to set up and use your doorbell device.

1. Downloading and installing the APP

Open App Store (for iOS) or Google Play Store (for Android outside China) or Yingyongbao Store (for Android inside China) on your device. Search for "TuyaSmart" to download the correct App for your device.

Visual Description: An image shows a smartphone screen displaying the TuyaSmart app icon and a QR code. The QR code is for downloading the app.

2. Setting up the APP

Before you begin:

• Make sure the TuyaSmart APP is installed on your device.
• Make sure that your device is connected to a 2.4GHz Wi-Fi network; 5GHz networks are NOT compatible.

User Register: New users should register according to the guide steps. Already registered users can simply log in.

Visual Description: A screenshot of a mobile app shows a "Register" screen with fields for "Mobile Phone Number/Email" and "Get Verification Code". Below these fields, there's a button to "Agree Service Agreement and Privacy Policy".

3. Add the device

Before adding, make sure the device is in configuration - with a voice notification "Please use the APP to set up the network" (Blue light blinks per 1s).

If you didn't hear the voice notification, please RESET the device by pressing the home button for 5 seconds. You can release the button after the LED indicator has turned off; the device will restart to default setting automatically.

Visual Description: A screenshot of the TuyaSmart app shows the "Add Device" screen with options like "Add Manually" and "Auto Scan". Another screenshot shows the "Enter Wi-Fi Password" screen, prompting for the Wi-Fi password and confirming that only 2.4 GHz Wi-Fi networks are supported.

When you hear the prompt "connecting the network", choose "Continue" and use the camera to scan the QR Code shown on your phone. Ensure about 15-20cm distance between the mobile device and the doorbell. When you hear the prompt "connecting the network", tap "I heard a Prompt" and wait for device connection until success.

If your camera fails to connect, please try to RESET the camera and repeat all steps again.

Visual Description: Screenshots illustrate the process: "Use Camera to Scan QR Code" with a QR code displayed, and then "Device added successfully" indicating completion.

When the app shows "Device added successfully", congratulations! The device is ready for use now!

4. WiFi Doorbell Functions

The doorbell supports the following functions: Two-way Audio; Video recording to local file; Take Photo; Playback video on Micro SD card.

4.1 Live view

In the device list section, all successfully connected devices are shown. Click the corresponding device to view live videos directly.

Visual Description: A screenshot of the app's main screen shows a list of devices, including "Smart Video Doorbell" with status indicators like signal strength and battery remaining.

4.2 Micro SD Card Video Playback

Micro SD Card Recording Types:

• APP wake up the device and take video
• Press button to wake up the device and take video
• Motion detection and take video

Remark: Currently the device only supports Micro SD cards with the FAT32 system format; others cannot be identified.

Visual Description: A screenshot of the app's playback interface shows video controls, including options for replay, record, and photograph.

5. Device Management

Click the corresponding device to view live videos directly in the device list section. You can choose the settings icon at the top right corner to enter device settings.

Visual Description: A screenshot of the app's device settings screen shows options like Device Name, Share Device, Device Information, Power Management Settings, Basic Function Settings, PIR, Memory Card Settings, Feedback, and Firmware Information.

5.1 Modify Device Name

Click "Device Name" on the setting page to rename the device.

5.2 Device Sharing

Click "Share Device" on the setting page to share the device to other family members.

5.3 Device Information

Click "Device information" on the setting page to check device information.

5.4 Power Management Setting

Click "Power Management Setting" to check power working status or set the low battery alarm threshold.

Options: 10%~50%

5.5 Basic Function Setting

Click "Basic Function Setting" to set below functions:

• Flip Screen: on/off
• Time Watermark: on/off
• Talk Mode: One-Way Talk/Two-Way Talk

5.6 PIR sensitivity Setting

Click "PIR" to set the sensitivity.

PIR Options: Low/Medium/High/Off

• Off: Closes PIR function.
• Low: Wakes up and records footage if any motion in front of the camera lasts for more than 7 seconds. A notification will be sent to mobile devices at the same time.
• Medium: Wakes up and records footage if any motion in front of the camera lasts for more than 5 seconds. A notification will be sent to mobile devices at the same time.
• High: Wakes up and records footage if any motion in front of the camera lasts for more than 1 second. A notification will be sent to mobile devices at the same time.

Note: In crowded environments, it is recommended to close or set the device to LOW sensitivity to reduce unwanted wake-up and notification push to extend battery life.

5.7 Memory Card Settings

Click "Memory Card Setting" to check Micro SD card status, including total capacity, used and remaining capacity, or to format the memory card.

6. Note for using

1. When the device is powered by rechargeable lithium batteries, with fully charged, the battery life approximately could be around six months. The mobile device APP will send notification when battery voltage is low. Please charge the device in time if you get the notification.
2. Keep the camera within your router's range. Make sure to pick a place that is covered by your WiFi signal. Thick or insulated doors can greatly reduce the strength of your Wi-Fi signal even if your router is close by. Trial test before installing the camera is recommended.
3. The device is designed based on low power consumption components. It can be remotely woken up from the APP, by PIR human motion detection, or doorbell press. The device will work for 30 seconds after wake-up each time, then return to standby.

Technical Specification

1*5000 mA battery normally can support 3-6 months usage.

Visual Description: An image shows the back of the indoor unit, displaying its CE, FC, and ROHS certifications, and indicating a 5000mAh battery.

Function Introduction

• ? Can support 2~3 months of usage (depends on how many events trigger per day).
• ? Exquisite image recording with wide angle lens.
• ⚡ Fast mobile device remote wake up in less than 1 second.
• ? 2.4GHz WiFi connection.
• ?️ High quality two-way talk with noise cancellation.
• ? PIR motion detection, notification will be sent to your phone whenever motion is detected in front of your camera, never miss a thing!
• ? Day/Night mode automatic switching, ensuring the best image quality 7*24.