FREEGO F3 USER MANUAL

Introduction

Congratulations on becoming a proud owner of an Freego.

This machine offers cost savings on fuel and contributes to a greener environment. Some functions may be new to users. The content and specifications are valid at the time of printing, and the company reserves the right to alter them without prior notice.

To ensure the best driving experience, read this manual carefully. Keep it for future reference.

Safety Instructions

• For adults use only!
• Abide by local traffic regulations.
• Wear a helmet, knee, and elbow guards for safety.
• Read the relevant driving guidelines in this manual.

Be careful and pay attention to the safety of yourself and others when riding. The manual contains important safety information.

Chapter I: Introduction

The Freego is a two-wheeled self-balancing scooter based on "dynamic stability." A built-in gyroscope and a high-speed central microprocessor, powered by a 24V-28Ah battery, manage the vehicle's balance.

It can be classified as a double-wheeled unicycle or a power stand-up scooter. Officially, it's known as an Electric Personal Assistive Mobility Device (EPAMD).

The vehicle has dual wheels, is as wide as an adult's shoulder, weighs 56 kg, and is battery-operated. It does not require brakes or a throttle. Leaning forward makes it move forward; returning to an upright position stops it. It uses the dynamic balance principle, mimicking human balance by shifting the center of gravity. The wheels replace feet, providing precise balance actions. It uses two maintenance-free BTM batteries. A full charge provides approximately 5 hours of driving, with the range depending on driving style and terrain (grass and slopes consume more power).

Chapter II: Parts Explanation

The Freego features several key components:

• 1. Handle Bar/Turning Pipe: Used for controlling turns (left/right, 360 degrees) and aiding body balance. Its height is adjustable for driver comfort. The steering rod must be locked after adjustment before driving. The turning pipe can be detached for storage.
• 2. Power Switch: Turns the scooter on and off. When switched on, the Freego performs initialization settings. It is dangerous to stand on the scooter without the power on.
• 3. Pedal Switch (SAFE switch): A built-in safety switch that detects if a rider is on the scooter. If the driver leaves the Freego, the pedal switch resets, and the scooter stops after 2 seconds.
• 4. LCD displayer on Pedal: Shows the remaining battery percentage.

Diagram showing the Freego scooter with numbered parts: 1. Cramp, 2. Handel Grip, 3. Adjusting Screw, 4. Turing Pipe, 5. Steering Joint Shaft, 6. Tire Fender, 7. Tire, 8. Indicator, 9. Pedal, 10. Power Switch, 11. LED Flash Lights, 12. Fuse Jack, 13. Charging Jack.

Chapter III: Getting Started

1. The Right Starting Operation

To start correctly:

1. Hold the handle bar with one hand and step onto the pedal with the opposite foot (e.g., left hand on handlebar, right foot on pedal).
2. Ensure the pedal is upright.
3. Turn on the power switch. A continuous green light indicates successful initialization.
4. Firmly hold the handlebar with both hands.

It's crucial that the pedal is in the upright position when the power is turned on, as this sets the original position for balance. An incorrect initial position can affect driving balance.

Pictures showing correct starting: Person holding handlebar, stepping onto pedal with one foot (P2, P3, P4), then holding handlebar with both hands (P5).

2. The Wrong Starting Operation

If the pedal is not vertical when starting, the Freego may have difficulty balancing. The original position can be reset by turning the power off and on repeatedly. If the pedal is not vertical, turn the Freego off, place the pedal vertically, then turn it back on and test. Repeat until the best state is achieved.

Pictures illustrating wrong starting positions with 'X' marks (P6, P7).

3. Correct Example

Ensure the Freego is kept upright before powering on.

Picture showing a correct starting posture with a checkmark (P8).

Chapter IV: Driving

Driving the Freego is different from conventional vehicles as it lacks brakes, accelerators, or gears. Read the manual or seek instruction before your first ride.

1. Standing on Freego

After powering on, hold the handlebar and step onto the pedals with one foot at a time. The computer will initiate balance. Stand upright, relax, and the Freego will remain stationary.

Pictures showing a person stepping onto the Freego pedals (P9) and standing upright (P10).

2. Driving Straight Forward

Lean your body forward slowly using your center of gravity. Speed is controlled by the leaning angle; more lean means faster speed. For stable driving, lean forward gradually.

Picture showing a person leaning forward to drive the Freego (P11).

3. Braking and Driving Backward

Driving backward is not recommended due to limited visibility. The Freego has a zero turning radius, allowing 360-degree spins. To slow down or stop, lean backward or squat slightly to shift your center of gravity backward. Lean slowly and smoothly for safe stopping.

Picture showing a person leaning backward to slow down or stop the Freego (P12).

Tip: To drive forward in a straight line, push the handle forward; to slow down or stop, push it backward.

4. Turning at Original Place, Turn Around and Rotate 360

Turning is achieved by moving the handle bar forward/backward and leaning your body accordingly. Returning the handle bar to the original position and standing straight will stop the Freego.

Pictures showing turning maneuvers with the handle bar and body lean (P13, P14).

5. Turning in Driving Degrees

Turning range is speed-dependent; faster speeds result in a smaller turn range for safety. Turning involves coordinating the handle bar and body lean. The Freego is described as a "thinking car" that responds to the driver's intentions.

6. Driving in Bad Weather

The Freego is not waterproof. Avoid driving in rain, as water can damage the motherboard and motor. Do not drive in snow. It lacks night lights, so avoid dark conditions. In Australia, it may not be permitted on public roads used by motor vehicles. Comply with local traffic regulations when driving on sidewalks, driveways, or public places.

Chapter VI: Charging

When the orange and red indicator lights are continuously on, the battery needs charging.

1. Turn off the power switch.
2. Use the specialized 36V battery charger and insert the plug into the Freego's charge jack.
3. Connect the charger to the power source.

The charger's red light indicates charging, and the green light indicates a full charge. The charger has an input voltage of 110-240V and an output voltage of 37-39V, with an AC electric current of 1.2-1.5A. Charging takes 8-10 hours. The charger may become warm during use.

Picture showing the Freego scooter connected to its charger (P15).

Keep the power switch off during charging to prevent power consumption.

Chapter V: Maintenance

Maintenance tasks not detailed below should be performed by a professional.

1. Battery Maintenance

The Freego uses BTM free maintenance batteries. Charge when the orange and red indicator lights are continuously on. Do not exceed 15 hours of charging. For long periods of non-use, keep the battery charged; excessive discharge and recharge cycles can shorten battery life. It is recommended to charge the battery monthly, even if not in use.

2. When not driving Freego

Turn off the power switch and lock it to prevent accidental starting.

3. Replacing Fuse

The Freego uses a 50A car fuse, which may burn out due to overload or impact. If the scooter does not respond after powering on and the indicator is off, check the fuse. Open the fuse cover at the back of the body with a screwdriver, remove the fuse with clamp, and replace it with a new one.

4. Fastening Nut of Tire

Regularly check wheel screws for tightness. Tighten loose screws with an 18mm spanner to 108 torque.

5. Maintenance of Tire

Maintain normal air pressure for safe driving. The standard tire pressure is 100 kPa (1.0 bar / 1.02kg/cm²). Check tire pressure regularly. Under-inflation or over-inflation can cause uneven tire wear, affecting comfort, mileage, and battery life. Check for cuts and splits that could lead to rapid deflation and rider injury.

6. Appearance Cleaning

Keep the pedal and body of the Freego clean. Remove gravel, dirt, and mud after driving. Do not use corrosive chemicals like petrol. Clean with a soft cloth and brush; do not wash with water.

Chapter VI: Notice

1. Keep Pedal of Freego Horizontal

The Freego sets the pedal position at power-on as its original setting. The pedal must not be horizontal after power-on; it should be vertical for the driver to stand. If the pedal position changes due to gyroscope warming up, adjust by repeated power on-off.

2. Balance Output of Freego

Computer balance activates when the pedal switch is pressed. The computer maintains balance even if the pedal switch is released at low speeds. If the driver needs to push the Freego, it may tend to move forward. Do not leave the Freego unattended on the road, as it may move automatically until it falls.

3. Freego Standing

To make the Freego stand after driving, turn off the power and deploy the bracket.

1. Accidental Submersion

If the Freego accidentally falls into water, turn off the power immediately. Do not drive it if unsure of its condition. If a fault persists, contact customer service for assistance. The Freego weighs 56kg and can be pulled manually.

2. Lock Switch

Lock the Freego to prevent accidental movement. Power off and then lock. When powered on again, pressing the pedal switch will result in no action, indicating the Freego is locked.

Chapter VII: Sound Alarm

Ensure the pedal switch is in the correct position (pressed down) to prevent the Freego from switching off power and losing balance.

2. Sound alarm 4 times

A pedal problem can cause a 4-time alarm. Try pressing the pedal switch several times to reset it. If the alarm persists after powering on, contact customer service.

3. Sound alarm 3 or 2 times

These alarms indicate potential vehicle problems:

• Sound alarm 2 times: Problem with the gyroscope.
• Sound alarm 2 times: Problem with the accelerometer.

In these cases, the transducer may have an issue. Turn off the power, stop driving, and contact customer service.

5. Sound alarm (Low Battery)

The LCD displayer shows battery power below 30%. The battery is low and needs immediate charging. Always charge the battery before it fully depletes to prevent damage and prolong its life.

Chapter IX: Technical Data

Chapter X: Warranty

For any issues with your Freego, contact your local distributor via email.

A 12-month parts-only warranty is provided for faults arising from natural causes. Accidents are not covered, but service is available for a fee.

Instruction for remote switch

The Freego comes with a remote switch for controlling various functions when the scooter is powered on:

• Lock: Press before powering off to lock the Freego.
• Unlock & Enable/Disable Towing: If the scooter is locked (no action after pressing the pedal switch), press this button to unlock. Press again to enable towing mode for pulling the Freego; press again to cancel towing mode.
• Speed Setting: Set speed limits: 3 beeps for 18km/h, 2 beeps for 12km/h, 1 beep for 8 km/h.
• LED Flash Lights Switch: Turn the front and rear LED flash lights on or off.

Keep the remote switch safe. If lost, contact your distributor to obtain a new one and learn how to match the code.

Diagram of the remote controller for the F3 Freego Scooter Off-road, showing buttons for Lock, Unlock/Towing, Speed setting, and LED Flash Lights ON/OFF.