Specifications
| Model No. | Abyss TR (MFG. M908) |
|---|---|
| Case size | L510*W232*H526mm |
| Material | Steel/ABS |
| M/B Type | E-ATX/ATX/Micro-ATX/ITX |
| 5.25" Drive Bay | N/A |
| HDD Drive Bay | 3.5" HDD*2 / 2.5" SSD*4 |
| Expansion Slots | 7 Slots Support VGA card 420mm |
| Height of CPU Cooler | 170mm |
| Cooling system | Top: 120mm*3/140mm*2 (By specify) Front: 120mm*3 (By specify) Rear: 120mm*1 (By specify) |
| Dust filter | Bottom dust filter*1; Top dust filter*1 |
| I/O Panel | USB3.0*2, USB2.0*2, HD Audio/MIC |
| Controller | V1.7 control Hub for Fan light Top panel 2 channel controller for Fan speed |
| PSU | Standard ATX PSU |
Parts Identification
The diagram shows the components of the GAMEMAX Abyss TR PC case. Key parts include:
- 1. Front panel
- 2. Right side panel
- 3. Left side tempered glass panel
- 4. Top panel
- 5. Top dust filter
- 6. Top fan place
- 7. Rear fan place
- 8. Front fan place
- 9. PSU Place
- 10. M/B place
- 11. ODD place
- 12. 3.5/2.5 HDD Rack
- 13. SSD rack
- 14. Bottom dust filter
- 15. Foot
- 16. V1.7 control Hub for Fan light
Installation Procedures
How to install PSU
Insert the PSU into the designated PSU place. Fix it securely with screws.
How to install 3.5"HDD & 2.5"SSD
Remove the bay bracket. Insert the hard drive (HDD or SSD) into the bracket or designated slot. Fix with screws.
How to install M/B
Install the Motherboard (M/B) onto the M/B tray, aligning it with the standoffs. Ensure proper screw placement. The diagram indicates typical motherboard dimensions (e.g., 305mm, 330mm) and screw hole locations.
How to install 2.5"SSD
SSD place 1: Loosen screws to remove the SSD bracket. Install the 2.5" SSD onto the bracket and fix it with screws. Then, insert the SSD bracket back into its place.
SSD place 2: Insert the 2.5" SSD directly into the designated mounting spot. Fix with screws.
How to install the radiator
Radiators can be installed in multiple locations within the case:
- Rear panel: Place the radiator in the rear fan position and secure it with screws.
- Front panel: Place the radiator in the front fan position and secure it with screws.
- Top panel: Place the radiator in the top fan position and secure it with screws.
Radiator Support Sizes:
- Front: 120mm, 240mm, 360mm
- Top: 120mm, 140mm, 240mm, 280mm, 360mm
- Rear: 120mm
User Options
No.1 How to install VGA card fix unit (User option)
Install the VGA card support unit. This involves loosening specific screws (1, 2, 3) and adjusting components (A, C, B) as indicated in the diagram for proper alignment and support.
No.2 How to install water tank (User option)
Install the water tank into its designated mounting location within the case. Secure it with screws.
No.3 How to use RAM cooler guide install 2.5"/3.5"HDD/SSD
Follow these steps to use the RAM cooler guide for installing 2.5"/3.5" HDDs/SSDs:
- Loosen screw 1 and adjust component A.
- Loosen screw 2 and screw 5, then adjust component C.
- Loosen screw 3 and screw 4, then adjust component B.
Cable Connection Instructions
Connect the following cables to their respective motherboard headers:
- HDD LED M/B connector connects to the H.D.D LED header.
- POWER LED M/B connector connects to the POWER LED + and POWER LED - headers.
- Reset S/W M/B connector connects to the RESET SW header.
- Power S/W M/B connector connects to the POWER SW header.
Top Panel Fan Connection
This section details the fan connection setup for the top panel. 3-pin fan connectors from the fans are connected to a manual fan controller. This controller is then powered by the system's PSU via a 4-pin Molex connector.
V1.7 A-RGB(RAINBOW) Control HUB
Schematic Diagram of Connection
The V1.7 A-RGB Control HUB schematic illustrates its connectivity:
- It receives power via a standard SATA connection from the power supply.
- It features two RGB strip connectors (STRIP1, STRIP2).
- A manual control switch can be connected to the designated port.
- It can connect to the motherboard's +5V A-RGB interface using an optional SYNC cable.
- An ADD GEN 2 connector is present with pins for Data, Ground, and +5V.
Product Features
- 1-1. 18 pre-configured color modes.
- 1-2. Mode and color adjustment.
- 1-3. SATA power input.
- 1-4. +5V A-RGB Mainboard SYNC capability.
Functional Description
- 2-1. Change between M/B-SYNC and independent mode: The default mode is independent. Press the RGB key for 3 seconds; the white light will flicker, indicating M/B-SYNC mode. Release the key to enter M/B-SYNC mode. Press the RGB key again to return to independent mode.
- 2-2. Turning light off: In independent mode, press and hold the RGB key for 3 seconds. The white light will flicker. If you continue to press the key, the light will turn off. Press the RGB key again to turn the light back on.
- 2-3. Memory function: This controller retains the last used lighting settings.
- 2-4. Selecting mode and colors within RGB key: Short press the RGB key once to change the lighting mode. Short press the RGB key twice to change colors within the currently selected mode.
- 2-5. A-RGB M/B-SYNC: After connecting the +5V sync cable to your motherboard, the RGB effects can be switched to M/B-SYNC mode as described in section "Change between M/B-SYNC and independent mode".
- 2-6. LED-Strip: Additional LED strips can be connected and controlled via the control HUB.
