Installation Guide for Yale models including: NTT600PBACC, 2ABFG-NTT600PBACC, 2ABFGNTT600PBACC, NTT600PBACC Deadbolt Smart Door Keypad, Deadbolt Smart Door Keypad, Door Keypad, AU-NTT620-ACC nexTouch Keypad Access Exit Trim Lock, Keypad Access Exit Trim Lock, Exit Trim Lock, AU-NTT620-ACC
iRevo-ASSA ABLOY Korea NTT600PBACC 2ABFG-NTT600PBACC 2ABFGNTT600PBACC ntt600pbacc
nexTouchTM Keypad Access Exit Trim Lock Touchscreen and Push Button Installation and Programming Instructions WARNING This product can expose you to lead which is known to the state of California to cause cancer and birth defects or other reproductiveharm.For more information go to www.P65warnings.ca.gov. 08/2018 Retrofitting or modifying this product may impact fire rating, safety features and warranty. Consult with code specifications to ensure compliance with all codes and ratings. Part of ASSA ABLOY 80-8470-0900-000 04-21 Before You Begin AA AA AA AA template Fire Guard Optional Optional Network Module Privacy DPS Switch Tools Needed Outswinging Door Left Hand Reverse Interior Right Hand Reverse Part of ASSA ABLOY #3 & #2 3/4" 1/2" Exterior Face a door swinging open toward you. If it swings open to the right, it is a right hand reverse door. If it swings opens to the left, it is a left hand reverse door. 2 80-8470-0900-000 04-21 O Door Position Switch Option optional Privacy DPS Switch With Door Position Switch installed and door closed, all keypad functions can be disabled by Privacy Button. 1 Prepare Door DPS Option for Privacy Function Wood Door: 3/8" Dia. Thru to Hole in Door Face *Metal Door: 3/4" Dia. Thru to Hole in Door Face template *Metal Door Installations Supplied plastic collar MUST be installed for DPS to function properly. Part of ASSA ABLOY 3 Drill holes 1/2 way thru door then complete from other side to prevent splitting. 80-8470-0900-000 04-21 2 Install Cylinder X Tighten counter-clockwise to secure lock. Use key to thread cylinder. Pull key out of cylinder to first blade cut for best operation. If using cylinder other than 1-1/8", a new collar must be used that is sized appropriately for cylinder length. Test Cylinder Test cylinder by turning key counter-clockwise to unlock trim. If there is any binding then cylinder is not at correct depth and needs to be threaded further into escutcheon. Part of ASSA ABLOY 4 80-8470-0900-000 04-21 3 Change Hand of Trim (if necessary) Left Hand Reverse Right Hand Reverse There is a spring inside spindle. Be sure to keep spring for reassembly. 2 1 Nut loToigshentejnusntuetnthoeunghSpTianbdle that spindle tab aligns with top of hole. 1 2 1 2 1 Be sure spring 2 is inside spindle. Set screw should be located on same side as lever arm. Part of ASSA ABLOY 5 80-8470-0900-000 04-21 4 Install Outside Trim Assembly #10-32 x 1" OHPMS Do not take apart outside assembly. x2 2 hinge side screws hold outside trim assembly until exit device is installed. 1 All 4 screws MUST be used for proper installation. Do not tighten screws until exit device 2 installation -Step 5. Part of ASSA ABLOY 6 Exit Device Mounting Holes 80-8470-0900-000 04-21 5 Install Exit Device #10-32 x 1" PHMS x2 Refer to exit device installation instructions for details of device installation. 3 Tighten all screws. 4 Test Mechanical Lock Function by Key, Lever and Keypad Part of ASSA ABLOY 7 80-8470-0900-000 04-21 6 Install Strike and Optional DPS #10-24 PFHMS x3 DPS Option for Privacy Function *Metal Frame: 3/4" Dia. x 1" Frame See Instructions with DPS Kit *Supplied plastic collar MUST be installed for DPS to function properly. 3-1/2" Strike must be centered with exit device bolt. For proper engagement, door should remain latched and not rattle when pushed, pulled or shaken in/out. Refer to exit device installation instructions for details of strike installation. Part of ASSA ABLOY 8 80-8470-0900-000 04-21 7 Install Inside Mounting Plate OR x2 #8 x 3/8" PRH Sheet Metal x2 #8 x 1/2" PHWS Wood x1 #10-32 x 1-1/2" THPMS Inside of Door 1 2 Optional DPS Part of ASSA ABLOY 9 80-8470-0900-000 04-21 8 Attach Cables to Inside Lock Reset Button External Power Optional DPS Connection Motor Connection Keypad Connection Part of ASSA ABLOY 10 80-8470-0900-000 04-21 9 Install Inside Lock #8-32 x 5/16" PHMS x3 Avoid crimping cables! Do not tighten screws until lock is flat against plate without excessive pressure. Part of ASSA ABLOY 11 80-8470-0900-000 04-21Acrobat Distiller 21.0 (Windows)