Kemimoto Product Manual

BEFORE YOU BEGIN

1. Please read the instructions carefully and verify that each item is in the list.

2. Please retain these installation instructions for further reference and parts ordering information.

IMPORTANT

1. Please read the installation instructions carefully before you start.

2. If the vehicle is clean and free of other debris, it will be easy to install.

3. For your safety and to ensure a satisfactory installation, please complete all the installation steps in the order shown below.

PRODUCT INFORMATION

This section lists the components included with the product. The product is a pair of speakers with mounting hardware and control units.

INSTALLATION TIPS

Estimated installation time: 50 minutes. Required tools: Open ended Allen spanner wrench.

STEP 1: Pre-assembly

Pre-assemble the speaker [1] and bracket [2] together with eight screws [4], washers [5], and flat washers [6].

STEP 2: Mount Clamp

Fit the throat clamp [3] onto the front and rear crossbeams of the vehicle's roof roll cage. This clamp is designed for crossbeams with a diameter of 1.75-2.0 inches.

STEP 3: Secure Speaker Assembly

Adjust the position of the support bracket [2] according to the distance of the roll bar. Tighten the screw on the back of speaker [1] when it is in the appropriate position to secure it. Fix speaker [1] bracket [2] onto the roll bar through the throat pipe [3]. Note: the bracket [2] is adjustable within a length range of 450-755mm (17.7-29.5 inches).

WIRING DIAGRAM

The wiring diagram illustrates the system connections:

• Power Supply connects to the Power Connector.
• Signal Connector from speakers connect to the Controller.
• Bluetooth Signal Line connects to the Controller.
• Controller has connections for USB Connector, AUX IN Connector, and CONTROLLER Connector.
• The system supports USB and AUX inputs.
• The diagram shows two speaker units, each with a connector, linking to the controller.

STEP 4: Connect Power Wires

Connect the Red Wire (+) to the positive terminal and the Black Wire (-) to the negative terminal of the power source.

STEP 5: Connect Main Unit

Connect the main unit's power and signal cables as per the wiring diagram.

FUNCTION AND OPERATION

Control Buttons:

• ① Power/Mode Button: Long press [O/MOD] for power on/off. Short press [O/MOD] to cycle through BT-AUX-USB modes.
• ② Play/Pause Button: When playing USB, AUX, or Bluetooth music, short press for pause function; short press again to resume playback.
• ③ Previous Track/Decrease Volume Button: When playing music, short press for previous track selection. During music playback, long press for volume decrease function.
• ④ Next Track/Increase Volume Button: When playing music, short press for next track selection. During music playback, long press for volume increase function.

BLUETOOTH PAIRING

Pair your phone with your speaker:

1. Long press the Power/Mode button [O/MOD] to turn on the unit.
2. Short press [O/MOD] again to switch to BT (Bluetooth) mode.
3. Bring your phone close to the main unit and turn on the Bluetooth function on your phone.
4. Search for the main unit's Bluetooth name "KEMIMOTO-T1" on your phone.
5. Once the Bluetooth connection is successful, the main unit will emit a "ding" sound.

FCC Caution

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC's RF Exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. Use only the supplied antenna.