Thermador PRD48WDSGU 48-Inch Dual-Fuel Pro Grand® Range

Features & Benefits

• ExtraHigh Star® Burner provides 22,000 BTUs of power for searing or boiling with QuickClean Base® designed for easy surface cleaning.
• 4 ExtraLow® burners offer precision simmering, melting or keeping warm.
• Non-stick griddle provides even heating across the entire cooking surface.
• Steam oven features 9 advanced conventional cooking modes.
• Super Fast 2-hour self-clean mode is the fastest in the industry.

Technical Details

Warranty

Limited Warranty, Entire Appliance, Parts and Labor: 2 Year

Rangetop

Total Number of Cooktop Burners: 6 + Griddle

Oven

Dimensions & Weight

Accessories (Included)

• 3 Telescopic Racks
• 1 Sm. Std. Rack
• Multi-Point Meat Probe
• 1 Griddle Plate
• 1 Grease Tray
• 1 Steam Pan
• Island Trim

Accessories (Optional)

• Wok Ring (PWOKRINGHC)
• Professional Griddle (PAGRIDDLE)
• 12" Pro Griddle with Tray (PAGRIDLFW)
• 12" Professional Griddle Cover (PA12LCVRW)
• Chopping Block / Cutting Board (PA12CHPBLK)
• 12" Pro Grill Plate with Tray (PA12GRILLW)
• 12" Grill Plate with Tray (PA12GRILFW)
• 7" Low Backguard (PA48WLBG)
• Toekick (PA48WTKG)
• Metallic Blue Knob Kit (PARKB48SGY)
• LP Conversion Kit, Pro Grand Dual-Fuel Models with 4 and 6 Burners (PALPKITDGW)
• Perforated Cooking Pan, Full Size, 1 5/8" Deep (00577551)
• Cooking Pan, Full Size, 1 5/8" Deep (11027159)
• Cooking Pan, Half Size, 1 5/8" Deep (00577552)
• Baking Tray, Full Size, 1 1/8" Deep (00741839)
• Perforated Cooking Pan, Half Size, 1 5/8" Deep (00577553)
• High Altitude Kit, Natural Gas or Dual-Fuel Pro Grand Ranges, 5,400 ft. to 10,200 ft. (PAALTKITGW)
• High Altitude Kit, Gas or Dual-Fuel Pro Grand Ranges Connected to LP Gas, 10,000 ft. to 10,200 ft.

48-Inch Range Dimensions

Diagram showing overall dimensions: Height 47 15/16" (1218 mm), Width 29" (737 mm), Depth 30 5/8" (778 mm), Back Height 27 7/8" (708 mm), Front Height 25 3/4" (654 mm), Overall Depth 49 1/8" (1248 mm). The height range is 35 3/4" - 36 3/4" (908-933 mm).

48-Inch Range Cutout Dimensions

Diagram illustrating cutout dimensions and clearances. A table provides clearances (X, C, D, E) for different range models (All Harmony series, 36"/48" Grand series, 60" Grand series) based on Gas zone A and Electric zone B.

48-Inch Range Dimensions and Clearance Requirements with "Low Back"

Diagram illustrating side view with clearance requirements. A 36-inch minimum clearance is required between the top of the cooking surface and the bottom of an unprotected cabinet. A 30-inch clearance can be used when the bottom of the wood or metal cabinet is protected by not less than 1/4 inch of a flame retardant material. The diagram shows dimensions for "Low back" installation, including height to combustible materials (36"/914 mm min.), depth (29 3/8"/746 mm), recess depth (25 1/8"/638 mm max.), and overall depth (49 1/8"/1248 mm). It also indicates a 7" (178 mm) low back and combustible back wall.

Note: Clearances from non-combustible materials are not part of the ANSI Z21.1 scope and are not certified by CSA. Clearances of less than 6" (152 mm) must be approved by the local codes and/or by the local authority having jurisdiction.

48-Inch Range Dimensions and Clearance Requirements with "Flush Island Trim"

Diagram illustrating side view with clearance requirements for "Flush Island Trim". A 36" (914 mm) minimum clearance to combustible materials is shown. For Flush Island Trim installations, the counter surface should have a cantilever edge meeting the back section of the Flush Island Trim accessory. The diagram shows dimensions for recess depth (25 1/8"/638 mm max.) and overall depth (49 1/8"/1248 mm). It indicates a 6" (152 mm) minimum clearance to combustible surface with Flush Island Trim. The shaded area behind the range indicates minimum clearance to combustible surfaces, and combustible materials cannot be located within this area. A note specifies that if an inner wall is used under the cantilever counter top, there should be a 1/8" (3 mm) gap from the rear of the range to the inner wall.

Note: As defined in the "National Fuel Gas Code" (ANSI Z223.1, Current Edition). Clearances from non-combustible materials are not part of the ANSI Z21.1 scope and are not certified by CSA. Clearances of less than 6" (152 mm) must be approved by the local codes and/or by the local authority having jurisdiction.

Contact Information

For more information, contact Customer Support. High Altitude Kit details are provided for Natural Gas or Dual-Fuel Pro Grand Ranges connected to LP Gas at specific altitudes.

Disclaimer: Specifications are for planning purposes only. Refer to installation instructions and consult your countertop supplier prior to making counter opening. Consult with a heating and ventilation engineer for your specific ventilation requirements. Thermador reserves the right to change product specifications or design without notice. Some models are certified for use in Canada. Thermador is not responsible for products that are transported from the U.S. for use in Canada.

For support: 1 800 735 4328 | USA THERMADOR.COM | CANADA THERMADOR.CA | ©2025 BSH HOME APPLIANCES CORPORATION. ALL RIGHTS RESERVED.