Haier Split Type Room Air Conditioner Operation Manual

Important Information

Please read this operation manual carefully before using the air conditioner. Keep this manual for future reference. This appliance is filled with R32 refrigerant.

WARNING: This appliance contains a UV-C lamp. Read the maintenance instructions before opening the appliance. Eye or skin irritation may result from exposure from the top air inlet and inner part. Ensure the power is cut off before performing maintenance. UV-C barriers bearing the ultraviolet radiation hazard symbol should not be removed. Do not operate UV-C lamps outside the appliance. The appliance must be disconnected from the power supply before replacing or cleaning the UV-C lamp. If the UV-C lamp is damaged, it must be replaced by the manufacturer, its service agent, or similarly qualified persons to avoid a hazard. Unintended use or damage to the housing may result in the escape of dangerous UV-C radiation, which can cause harm to eyes and skin.

Parts and Functions

Indoor Unit

• Inlet: Air inlet
• Air Purifying Filter (inside)
• Display Board: Shows setting temperature and operation mode.
• Emergency Switch
• Horizontal flap: Adjusts up and down air flow. Do not adjust manually.
• Vertical blade: Adjusts left and right air flow.
• Outlet: Air outlet

Remote Controller

The remote controller has various buttons for operation:

• POWER ON/OFF: Turns the unit on or off.
• TEMP +/-: Adjusts the temperature setting.
• FAN SPEED: Selects fan speed (LOW, MED, HI, AUTO).
• MODE: Selects operation mode (AUTO, COOL, DRY, HEAT, FAN).
• SWING: Controls the vertical flap for air flow direction.
• TIMER ON/OFF: Sets the timer for operation.
• QUIET: Reduces fan speed for quiet operation.
• SLEEP: Adjusts temperature for comfortable sleep.
• HEALTH: Activates UV sterilization function.
• EXTRA FUNCTION: Accesses additional functions like HEALTH and SWING settings.
• LOCK: Locks/unlocks buttons and LCD display.
• LIGHT: Controls the indoor LED display.
• CANCEL/CONFIRM: Cancels or confirms settings.
• RESET: Resets the remote controller if abnormal.

Outdoor Unit

• OUTLET
• INLET
• CONNECTING PIPING AND ELECTRICAL WIRING
• DRAIN HOSE

WiFi Setup

If your Air Conditioner has a Connected Appliance Information label, it is WiFi Connect Enabled. This allows remote monitoring and control via a smartphone app. Visit www.haier.com.au/smart or www.haier.co.nz/smart for more information.

Operation

Unit Start/Stop

Press the ON/OFF button on the remote controller to start or stop the unit.

Temperature Setting

Use the TEMP +/- buttons to adjust the desired temperature. Pressing the button once increases/decreases the temperature by 1°C. Holding the button down increases/decreases it more rapidly.

Fan Speed Selection

Press the FAN button to cycle through fan speeds: LOW, MED, HI, AUTO. In AUTO mode, the air conditioner automatically adjusts fan speed based on room temperature.

Air Flow Direction Adjustment

Use the SWING button to adjust the vertical flap. Pressing it repeatedly cycles through different flap positions (Pos.1 to Pos.4). Pressing it again stops the swing function. Use the EXTRA FUNCTION button to select Pos.2 and Pos.3.

Cautions:

• Turn off the unit before adjusting the flap by hand.
• Avoid adjusting all vertical louvers to the left or right when humidity is high to prevent condensate water.
• Do not keep the horizontal flap in a downward position for extended periods in COOL or DRY mode to avoid condensate water.

Timer On/Off Operation

Press the TIMER button to select TIMER ON, TIMER OFF, or TIMER ON-OFF mode. Use the TEMP +/- buttons to set the desired time (0.5-hour increments up to 12 hours, then 1-hour increments up to 24 hours). Press CONFIRM to set the timer. Press CANCEL to cancel the timer setting.

POWER/SOFT Operation

Use this function for rapid heating or cooling. Access it via the EXTRA FUNCTION button.

QUIET Operation

Press the QUIET button for silent operation. Press again to cancel.

Self Clean Operation

Press the Self Clean button to activate this function, which cleans the evaporator and condenser. The display will show "CL". The function runs for 20-30 minutes and exits automatically. Pressing other mode buttons can exit the function earlier.

Emergency Operation and Test Operation

Emergency Operation: Use when the remote controller is lost or defective. The system automatically selects the operation mode based on room temperature. It is not possible to operate in DRY mode.

Test Operation: Use when room temperature is below 16°C. Press and hold the emergency switch for more than 5 seconds. The unit will start cooling with high fan speed and stop automatically after 30 minutes.

Comfortable SLEEP

Activate via the EXTRA FUNCTION button. In COOL/DRY mode, the temperature rises gradually. In HEAT mode, the temperature decreases gradually then rises. This function cannot be used with the TIMER function.

Power Failure Resume Function

After a power failure, the unit will resume operation automatically after a 3-minute delay to protect the compressor.

Healthy Airflow Operation

Activate via the EXTRA FUNCTION button to adjust the louvers for optimal airflow. Do not direct the flap by hand.

HEALTH Operation

Activates UV sterilization to remove harmful microorganisms. Recommended for 1-2 hours daily. Avoid direct exposure to the UV lamp.

Maintenance

For Smart Use of The Air Conditioner

• Setting of proper room temperature
• Do not block the air inlet or outlet
• Close doors and windows during operation
• Use the timer effectively
• Prevent direct sunlight during cooling operation
• Turn off the power supply main switch if the unit is not used for a long time.
• Use the louvers effectively.

Remote Controller Maintenance

Wipe the controller with a dry cloth. Do not use glass cleaner or chemical cloths.

Indoor Body Maintenance

Wipe the unit with a soft, dry cloth. For stubborn stains, use a neutral detergent diluted with water. Wring out the cloth before wiping and then wipe off any detergent residue.

Air Filter Cleaning

1. Open the inlet grille by pulling it upward.
2. Remove the filter by pushing up the center tab.
3. Clean the filter using a vacuum cleaner or by washing it with water. Dry the filter completely in the shade.
4. Attach the filter correctly with the "FRONT" indication facing outwards. Ensure it is securely fixed.
5. Close the inlet grille.

Note: Air purifying filter is an optional part.

Replacement of Air Purifying Filter

1. Open the inlet grille.
2. Detach the standard air filter by sliding the knob upward.
3. Attach the air purifying filter into the right and left filter frames.
4. Attach the standard air filter (necessary installation). The white side of the photocatalyst filter faces outwards, and the black side faces the unit. The green side of the bacteria-killing medium filter faces outwards, and the white side faces the unit.
5. Close the inlet grille.

Notes on Air Purifying Filters:

• Photocatalyst filters are solarized every 6 months.
• Bacteria-killing medium filters require frequent cleaning with a vacuum cleaner or by flapping to maintain performance. Store in a cool, dry place away from direct sunlight when not in use.

Cautions

WARNING

• Call a Sales/Service Shop for installation. Do not attempt self-installation to avoid electric shock, fire, or water leakage.
• If abnormality such as burning is found, stop operation immediately and contact a sales shop.
• Use an exclusive power source with a circuit breaker.
• Check proper installation of the drainage securely.
• Use the proper voltage.
• Connect the power supply cord completely to the outlet.
• Do not use the power supply cord in a bundle.
• Take care not to damage the power supply cord.
• Do not use power supply cords extended or connected in halfway.
• Do not install in places with potential flammable gas leakage.
• Do not get the unit exposed to vapor or oil steam.
• Do not insert objects into the air inlet or outlet.
• Do not start or stop operation by disconnecting the power supply cord.
• Do not channel airflow directly at people, especially infants or the aged.
• Do not attempt to repair or reconstruct the unit yourself.
• Connect the earth cable.

CAUTION

• Do not use for storing food, artwork, precise equipment, breeding, or cultivation.
• Take fresh air occasionally, especially when gas appliances are running.
• Do not operate the switch with wet hands.
• Do not install the unit near a fireplace or other heating apparatus.
• Do not place animals or plants in the direct path of airflow.
• Do not place any objects on or climb on the unit.
• Do not pour water onto the unit for cleaning.
• Do not place flower vases or water containers on the top of the unit.

Troubleshooting

Normal Performance Inspection

• System does not restart immediately: The system has a 3-minute protection delay to prevent damage.
• Noise is heard: Swishing or gurgling noise is normal due to refrigerant flow. Cracking noise may occur due to temperature changes. A loud noise from airflow might indicate a dirty air filter.
• Smells are generated: May be due to smells from furniture, paint, or cigarettes circulating in the air.
• Mist or steam are blown out: This can occur during COOL or DRY operation due to sudden cooling of indoor air.

Dry Mode Fan Speed

In DRY mode, fan speed may be fixed at LOW when room temperature is lower than the set temperature +2°C.

Poor Cooling

Check power plug, power failure, blown fuse, dirty air filter, obstacles at inlet/outlet, incorrect temperature setting, open doors/windows, direct sunlight, or excessive heat sources/people in the room.

Multiple Check

Ensure the power plug is inserted, there is no power failure, the fuse is intact, the air filter is clean, there are no obstacles, the temperature is set correctly, doors/windows are closed, and direct sunlight is managed.

Specifications

The machine is adaptive in following situation

1. Applicable ambient temperature range:

(INVERTER) Outdoor: Max: 24°C DB/18°C WB, Min: -15°C DB

2. Power supply cord replacement: Must be done by manufacturer, service agent, or qualified person.

3. Fuse replacement: Indoor unit fuse: T.3.15A/250V. Outdoor unit fuse: T.25A/250V.

4. Wiring method: Must comply with local wiring standards.

5. Power plug accessibility: Must be easily reached after installation.

6. Waste battery disposal: Dispose of properly.

7. Appliance use by children/infirm persons: Not intended without supervision.

8. Supervision of children: Ensure children do not play with the appliance.

9. Power plug: Use a proper power plug that fits the power supply cord.

10. Power plug and cable: Must have local attestation.

11. Powering off: Turn off A/C first, wait at least 30 seconds before cutting off power.

Customer Support

For Haier Appliances:

• Australia: 1300 729 948 | haier.com.au
• New Zealand: 0800 424 372 | haier.co.nz

Important notice of Disclosure: Copyright © Fisher & Paykel Appliances 2019. All rights reserved. Product dimensions and specifications may change without notice. Contact Haier's Customer Care Centre for current product information.

Fisher & Paykel Australia Pty Ltd, Level 1, 1 Eden Park Drive, Macquarie Park, NSW 2113. Phone: 1300 729 948 Email: customer.care@haier.com.au

Fisher & Paykel Appliances Ltd, 78 Springs Road, East Tamaki, Auckland 2013. Phone: 0800 424 372. Email: customer.care@haier.co.nz