User Manual
This device is the bluetooth low energy module.
Model Name: 2JV
FCC ID: VPYLBCA1ZZ2DV
FCC Compliance Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
This device complies with below part 15 of the FCC Rules. Part 15 Subpart C
Since there is no space which indicates FCC ID on this module, FCC ID is indicated in a manual. If the FCC ID is not visible when the module is installed inside another device, then the module is installed must also display a label referring to the enclosed module.
The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.
The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
Antenna List
| Part number | Vendor | Peak Gain(dBi) | Type | Connector |
| Type2JV_Slim | Murata | +1.0 | Monopole | Trace |
| Type2JV_Tandem | Murata | 0 | Monopole | Trace |
Host Device Information
The following information must be indicated on the host device of this module:
Contains Transmitter Module FCC ID : VPYLBCA1ZZ2DV or Contains FCC ID : VPYLBCA1ZZ2DV
FCC Compliance Information:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
*If it is difficult to describe this statement on the host device due to the size, please describe in the user's manual and also either describe on the device packaging or on a removable label attached to the device.
Host Device Manual Statements
The following statements must be described on the user manual of the host device of this module:
FCC CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines as this equipment has very low levels of RF energy. [※]
※But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person's body.
Installation Manual - Dimensions, Marking
The module has the following dimensions and marking:
Dimensions: 9.4mm+/-0.2mm width, 5.6mm+/-0.2mm height, 1.3mm thickness.
Marking:
| Marking | Meaning |
| A | Pin 1 Marking |
| B | Murata Logo |
| C | 2D Code |
| D | Module Type |
Additional dimensions:
| Mark | Dimensions | Mark | Dimensions | Mark | Dimensions |
| L | 5.6 ± 0.25 | W | 9.4 ± 0.25 | T | 2.2max |
Installation Manual - Terminal Configurations (Top View)
The module has the following terminal configurations:
A visual representation of the pinout is provided, showing pins labeled A-1 through R-10.
| No | Terminal Name | No | Terminal Name | No | Terminal Name | No | Terminal Name | No | Terminal Name | No | Terminal Name |
| A-1 | GND | C-9 | P1 15 | G-9 | P1 04 | L-9 | P0 31 | Q-9 | GND | ||
| A-2 | LED 6 P0 28 | C-10 | GND | G-10 | P1 11 | L-10 | P0 11 M33 SWCLK | Q-10 | ANT OUT | ||
| A-3 | LED 4 P0 19 | D-1 | P1_13_GPADC_4 | H-1 | P1_12_GPADC_5 | M-1 | P0 09 UART BOOT TX | R-1 | GND | ||
| A-4 | LED 2 P0 21 | D-2 | P1 20 | H-2 | P1 02 | M-2 | P0 26 | R-2 | GND | ||
| A-5 | LED 1 P0 24 | D-9 | P1 14 | H-9 | P1 04 | M-9 | P0_12_CMAC_SWDIO | R-3 | GND | ||
| A-6 | LED 5 P0 29 | D-10 | LX | H-10 | P0 02 | M-10 | P0_10_M33_SWDIO | R-4 | GND | ||
| A-7 | LED 3 PO 20 | E-1 | P1 19 GPADC 7 | J-1 | GND | N-1 | P0 16 | R-5 | GND | ||
| A-8 | LED 0 P0 13 | E-2 | P1 22 | J-2 | P1 06 | N-2 | P0 07 | R-6 | GND | ||
| A-9 | GND | E-9 | P1 16 | J-9 | P0 01 | N-9 | GND | R-7 | GND | ||
| A-10 | GND | E-10 | LY | J-10 | P0 00 | N-10 | GND | R-8 | GND | ||
| B-1 | USBP P0 14 | F-1 | P1 09 GPADC 7 | K-1 | PO 08 UART BOOT RX | P-1 | P0 06 | R-9 | GND | ||
| B-2 | LED 7 P0 27 | F-2 | P1 10 | K-2 | P1 00 | P-2 | P0 17 | R-10 | GND | ||
| B-9 | GND | F-9 | P0 30 | K-9 | P1 03 | P-9 | GND | ||||
| B-10 | VBAT | F-10 | P1 17 | K-10 | P1 05 | P-10 | ANT IN | ||||
| C-1 | USBM PO 15 | G-1 | P1 18 GPADC 6 | L-1 | P0 25 GPADC 1 | Q-1 | RSTn | ||||
| C-2 | P1 21 | G-2 | P1 07 | L-2 | P1 01 | Q-2 | P0 18 |
Installation Manual - Land Pattern TOP View (Recommended)
A recommended land pattern for the antenna part is shown. The pattern consists of several pads with specific dimensions and spacing.
Dimensions are indicated for trace width and spacing, for example, 0.25mm, 0.2mm, 0.3mm, 0.5mm, 1.2mm, 1.35mm.
The distance (thickness) between the green pattern and the lower ground is 200 microns.
*Consideration should be given to change applications for traces other than the design specified in the manual.
Installation Manual (Slim) - Recommended pattern for antenna part
Slim antenna recommended pattern (green) between these terminals as follows:
A diagram shows the recommended pattern for a slim antenna, with dimensions for the traces and spacing.
The diagram also illustrates the internal components of the 2JV module, including BLE Antenna, RF Matching circuit, RF, Xtal, Flash memory, AHB Lite, LDO, DCDC, and VBAT.
*Consideration should be given to change applications for traces other than the design specified in the manual.
Installation Manual (Tandem) - Recommended pattern for antenna part
Tandem antenna recommended pattern (green) between these terminals as follows:
Two diagrams show the recommended patterns for a tandem antenna, one for the front side and one for the back side. These diagrams include dimensions for the traces and spacing.
The front side diagram indicates a resistance of 0Ω.
*Consideration should be given to change applications for traces other than the design specified in the manual.
Installation Manual - Operating Condition
| Parameter | Min | Typ | Max | Unit | |
| Supply Voltage | VBAT | 2.4 | 3.3 | 4.75 | V |
| VBAT for OTP programming*2 | 2.4 | 3.3 | 4.75 | V | |
| VBAT for OTP reading | 2.4 | 3.3 | 4.75 | V |
*1: Please keep derating / margin as much as possible at extreme temperature.
*2: Required temperature for programming is between -20°C and 70°C
*The output level can be varied by changing the value of the power index within the scope of the application. (power setting: -18, -12, -8, -6, -3, -2, -1, 0, 1.5, 2, 3, 4, 4.5, 5dBm)
