User Manual
This device is the bluetooth low energy module.
Model Information
Model Name: 2JV
FCC ID: VPYLBCA1ZZ2DV
FCC Compliance Information
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
This device complies with below part 15 of the FCC Rules. Part 15 Subpart C.
Since there is no space which indicates FCC ID on this module, FCC ID is indicated in a manual. If the FCC ID is not visible when the module is installed inside another device, then the module is installed must also display a label referring to the enclosed module.
The modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification.
The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.
Antenna List
| Part number | Vendor | Peak Gain(dBi) | Type | Connector |
|---|---|---|---|---|
| Type2JV_Model1 | Murata | +1.0 | Monopole | Trace |
| Type2JV_Model2 | Murata | 0 | Monopole | Trace |
Host Device Information
The following information must be indicated on the host device of this module:
Contains Transmitter Module FCC ID : VPYLBCA1ZZ2DV or Contains FCC ID : VPYLBCA1ZZ2DV
FCC Compliance Information: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
*If it is difficult to describe this statement on the host device due to the size, please describe in the user's manual and also either describe on the device packaging or on a removable label attached to the device.
The following statements must be described on the user manual of the host device of this module:
FCC CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF) Exposure Guidelines as this equipment has very low levels of RF energy. [※]
※But it is desirable that it should be installed and operated keeping the radiator at least 20cm or more away from person's body.
Dimensions and Marking
A diagram shows the physical dimensions and marking details of the module.
Marking Details:
| Marking | Meaning |
|---|---|
| A | Pin 1 Marking |
| B | Murata Logo |
| C | 2D Code |
| D | Module Type |
Dimensions:
| Mark | Dimensions | Mark | Dimensions | Mark | Dimensions |
|---|---|---|---|---|---|
| L | 5.6 ± 0.25 mm | W | 9.4 ± 0.25 mm | T | 2.2 max mm |
Terminal Configurations (Top View)
A diagram illustrates the pinout of the module, followed by a table detailing each terminal's function.
| No | Terminal Name | No | Terminal Name | No | Terminal Name | No | Terminal Name | No | Terminal Name | No | Terminal Name |
|---|---|---|---|---|---|---|---|---|---|---|---|
| A-1 | GND | C-9 | P1 15 | G-9 | P1 04 | L-9 | P0 31 | Q-9 | GND | ||
| A-2 | LED 6 P0 28 | C-10 | GND | G-10 | P1 11 | L-10 | P0 11 M33 SWCLK | Q-10 | ANT OUT | ||
| A-3 | LED 4 P0 19 | D-1 | P1_13_GPADC_4 | H-1 | P1_12_GPADC_5 | M-1 | P0 09 UART BOOT TX | R-1 | GND | ||
| A-4 | LED 2 P0 21 | D-2 | P1 20 | H-2 | P1 02 | M-2 | P0 26 | R-2 | GND | ||
| A-5 | LED 1 P0 24 | D-9 | P1 14 | H-9 | P1 04 | M-9 | P0_12_CMAC_SWDIO | R-3 | GND | ||
| A-6 | LED 5 P0 29 | D-10 | LX | H-10 | P0 02 | M-10 | P0_10_M33_SWDIO | R-4 | GND | ||
| A-7 | LED 3 PO 20 | E-1 | P1 19 GPADC 7 | J-1 | GND | N-1 | P0 16 | R-5 | GND | ||
| A-8 | LED 0 P0 13 | E-2 | P1 22 | J-2 | P1 06 | N-2 | P0 07 | R-6 | GND | ||
| A-9 | GND | E-9 | P1 16 | J-9 | P0 01 | N-9 | GND | R-7 | GND | ||
| A-10 | GND | E-10 | LY | J-10 | P0 00 | N-10 | GND | R-8 | GND | ||
| B-1 | USBP P0 14 | F-1 | P1 09 GPADC 7 | K-1 | PO 08 UART BOOT RX | P-1 | P0 06 | R-9 | GND | ||
| B-2 | LED 7 P0 27 | F-2 | P1 10 | K-2 | P1 00 | P-2 | P0 17 | R-10 | GND | ||
| B-9 | GND | F-9 | P0 30 | K-9 | P1 03 | P-9 | GND | ||||
| B-10 | VBAT | F-10 | P1 17 | K-10 | P1 05 | P-10 | ANT IN | ||||
| C-1 | USBM PO 15 | G-1 | P1 18 GPADC 6 | L-1 | P0 25 GPADC 1 | Q-1 | RSTn | ||||
| C-2 | P1 21 | G-2 | P1 07 | L-2 | P1 01 | Q-2 | P0 18 |
Land Pattern TOP View (Recommended)
A diagram shows the recommended land pattern for the antenna part.
Installation Manual (Model1)
Recommended pattern for antenna part
Model1 antenna recommended pattern (green) between these terminals as follow.
A diagram shows the recommended antenna pattern with dimensions.
A block diagram illustrates the module's internal components and connections, including BLE Antenna, RFIO, RF Matching circuit, AHB Lite, IC301 (Flash memory), LDO, DCDC, and VBAT.
The distance (thickness) between the green pattern and the lower ground is 200 microns.
*Consideration should be given to change applications for traces other than the design specified in the manual.
Installation Manual (Model2)
Recommended pattern for antenna part
Model2 antenna recommended pattern (green) between these terminals as follow.
Diagrams show the recommended antenna patterns for the front and back sides, including dimensions and resistance information.
*Consideration should be given to change applications for traces other than the design specified in the manual.
Operating Condition
| Parameter | Min | Typ | Max | Unit | |
|---|---|---|---|---|---|
| Supply Voltage | VBAT | 2.4 | 3.3 | 4.75 | V |
| VBAT for OTP programming*2 | 2.4 | 3.3 | 4.75 | V | |
| VBAT for OTP reading | 2.4 | 3.3 | 4.75 | V | |
| Operating Temperature Range*1 | -30 to +85 deg.C | ||||
*1: Please keep derating / margin as much as possible at extreme temperature.
*2: Required temperature for programming is between -20°C and 70°C
The output level can be varied by changing the value of the power index within the scope of the application.
(power setting: -18, -12, -8, -6, -3, -2, -1, 0, 1.5, 2, 3, 4, 4.5, 5dBm)
