Owner's Manual for RED models including: 069023 RF DIM Fade in Fade Out Push Plus RF LED Dimmer, 069023, RF DIM Fade in Fade Out Push Plus RF LED Dimmer, Fade Out Push Plus RF LED Dimmer, Push Plus RF LED Dimmer, LED Dimmer
069023 dimLED PR 1SL SLOW Fade-in Fade-out Push+RF LED Dimmer Fade-in Fade-out LED dimmer with smooth fading effect for soft start and stop. The fading speed can be set via knob potentiometer, 1S, 3S, 5S, 10S, 20S selectable. Connect with self-resetting metal button or push switch to achieve on/off and 0-100% dimming function. Push input can accept either positive or negative trigger. Match with RF 2.4G single zone or multiple zone dimming remote control optional. Over-heat / Over-load / Short circuit protection, recover automatically. Technical Parameters Input and Output Input voltage Input current Output voltage Output current Output power 12-48VDC 8A 12-48VDC 1CH,8A 96-384W Output type Constant voltage Warranty and Protection Warranty Protection 5 years recover automatically, Short circuit, Over-heat, Over-load Dimming data Input signal Control distance Dimming gray scale Dimming range Dimming curve PWM Frequency Package Size Gross weight Mechanical Structures and Installations RF 2.4GHz + Push Dim 30m(Barrier-free space) 4096 (2^12) levels 0 -100% Logarithmic 2000Hz (default) L114 x W38 x H26mm 0.053kg RF DIM RED Safety and EMC EMC standard (EMC) Safety standard Radio Equipment (RED) Certi cation ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4 EN 61348-1:2015+A1:2021 EN 61348-2-13:2014+A1:2017 ETSI EN 300 328 V2.2.2 CE, EMC, RED Environment Operation temperature Case temperature (Max.) IP rating Ta: -20 OC ~ +55 OC Tc: +85 OC IP20 RUN LED indicator Push switch push - Push switch push + Installation rack knob potentiometer for fading speed LED output LED output + Power input Power input + Installation rack 33mm 97mm Light on/off fading speed 18mm Rotate knobto switch fading speed,when the fading speed set to 1/3/5/10/20s, the RUN LED indicator will flash 1/2/3/4/5 times. 5S 5S 5S 5S 5S 10S 20S 10S 20S 10S 20S 10S 20S 10S 20S 1S 3S 5S 10S 20S Wiring Diagram Connect with self-resetting metal button, positive trigger input. Press the button to switch or adjust brightness, the button indicator always lights up. OUTPUT - PUSH-DIM NO NO GND PUSH RUN 1S 3S + Single color LED strip 1S 3S 1S 3S 1S 3S 1S 3S 1S 3S INPUT 12-48VDC + 5S 10S 20S User Manual Ver 2.0.1 2024.5 AC100-240V Power Supply 12-48VDC Constant Voltage Page 1 Connect with self-resetting metal button, positive trigger input. Press the button to switch or adjust brightness, the button indicator lights up when pressed. RUN Single color LED strip + 1S 3S OUTPUT - PUSH-DIM INPUT 12-48VDC NO NO GND PUSH + 5S 10S 20S 10S 20S 10S 20S AC100-240V Power Supply 12-48VDC Constant Voltage Connect with self-latching metal button. Press the button to power on or off the controller, the button indicator lights up when pressed. Use RF remote to adjust brightness optional. OUTPUT - PUSH-DIM NO NO GND PUSH RUN + Single color LED strip 1S 3S INPUT 12-48VDC + 5S AC100-240V Power Supply 12-48VDC Constant Voltage Connect with push switch panel, negative trigger input. Press the panel to switch or adjust brightness. OUTPUT PUSH-DIM GND PUSH RUN 1S 3S RF remote + Single color LED strip INPUT 12-48VDC 5S Push Switch AC100-240V Power Supply 12-48VDC Constant Voltage Match Remote Control Match: Switch off the power, then switch on power. Immediately short press on/off key (single zone remote)or zone key (multiple zone remote) 3 times on the remote. The light blinks 3 times means match is successful. Delete: Switch off the power, then switch on power. Immediately short press on/off key (single zone remote) or zone key (multiple zone remote) 5 times on the remote. The light blinks 5 times means all matched remotes were deleted. Push Dim Function The provided Push-Dim interface allows for a simple dimming method using commercially available non-latching (momentary) wall switch or metal button. Short press: Turn on or off light. Long press (1-6s): Press and hold to step-less dimming, With every other long press, the light level goes to the opposite direction. Dimming memory: Light returns to the previous dimming level when switched off and on again, even at power failure. Synchronization: If more than one controller are connected to the same push switch, do a long press for more than 10s, then the system is synchronized and all lights in the group dim up to 100%. This means there is no need for any additional synchrony wire in larger installations. We recommend the number of controllers connected to a push switch does not exceed 25 pieces, The maximum length of the wires from push to controller should be no more than 20 meters. User Manual Ver 2.0.1 2024.5 PWM duty(%) Dimming Curve 100 Gamma=1.6 90 80 70 60 50 40 30 20 10 10 20 30 40 50 60 70 80 90 100 Brightness(%) Page 2Corel PDF Engine Version 16.1.0.843