Inateck KB01104 Keyboard
Instruction Manual
Product Diagram
The product diagram illustrates the Inateck KB01104 Keyboard. It features a standard QWERTY layout. Key indicators and controls are identified as follows:
- Indicator 1 (White): Serves as the Caps Lock indicator when solid white, or indicates Bluetooth Channel 1 status (reconnecting: flashes once per second; pairing: flashes twice per second; connected/unconnected: off).
- Indicator 2 (Blue): Indicates Bluetooth Channel 2 status (reconnecting: flashes once per second; pairing: flashes twice per second; connected/unconnected: off).
- Indicator 3 (Red/Green): Serves as the Battery indicator (charging: solid red; fully charged: solid green) or indicates Bluetooth Channel 3 status (reconnecting: flashes red once per second; pairing: flashes red twice per second; connected/unconnected: off).
- Power Switch: Located on the device to turn it on or off.
Shortcut Keys
The keyboard includes dedicated shortcut keys for various functions. Note that some operations are specific to Windows.
- Esc
- F1: Brightness Down
- F2: Brightness Up
- F3: Undo
- F4: Task View
- F5: Lock Screen
- F6: Screenshot
- F7: Last Track
- F8: Play/Pause
- F9: Next Track
- F10: Mute
- F11: Volume Down
- F12: Volume Up
- Delete
- Backspace
Fn Key Lock (Windows Specific): You can press fn + esc to enable or disable the Fn key lock. By default, the Fn key lock is disabled.
- When Fn Lock is enabled: Pressing an F key (e.g., F1) triggers its primary function (e.g., dimming screen brightness). Pressing
fn+ F key simultaneously triggers the multimedia/shortcut function. - When Fn Lock is disabled (Default): Pressing an F key (e.g., F1) triggers the multimedia/shortcut function. Pressing
fn+ F key simultaneously triggers the primary function.
Combination of Fn and Other Keys:
fn+esc: Enable/Disable Fn Lockfn+alt+cmd: Check Battery Levelfn+1: Short press to enter Bluetooth Channel 1 pairing mode. Long press to enter Bluetooth Channel 1 pairing mode.fn+2: Short press to enter Bluetooth Channel 2 pairing mode. Long press to enter Bluetooth Channel 2 pairing mode.fn+3: Short press to enter Bluetooth Channel 3 pairing mode. Long press to enter Bluetooth Channel 3 pairing mode.
Bluetooth Pairing
Step 1: For first-time use, slide the power switch to the 'On' position. The KB01104 will automatically enter Bluetooth Channel 1 pairing mode. Alternatively, you can manually enter pairing mode by holding fn + 1 simultaneously. The Bluetooth indicator will flash white when in Channel 1 pairing mode.
Step 2: On your device (iPad or Windows), turn on Bluetooth. "Inateck KB01104" should appear in the list of available devices.
Step 3: Tap "Inateck KB01104" to pair. The Bluetooth indicator will turn off upon successful pairing.
Fix Bluetooth Pairing Problems:
- Go to your device's Bluetooth settings, find "Inateck KB01104" in the paired devices list, and delete any previous pairing records. Delete all if multiple exist.
- Hold
esc+fnsimultaneously for 3 seconds. The three indicators will blink 3 times, indicating the factory reset is complete. - Turn your device's Bluetooth off and then back on. Re-pair the keyboard with your Inateck KB01104.
LED Indicators
Detailed status of the indicator lights:
Indicator 1 (White)
- Caps Lock On: Solid white
- Caps Lock Off: Off
- Bluetooth Channel 1 - Reconnecting: Flashes once per second
- Bluetooth Channel 1 - Pairing: Flashes twice per second
- Connected/Unconnected: Off
Indicator 2 (Blue)
- Bluetooth Channel 2 - Reconnecting: Flashes once per second
- Bluetooth Channel 2 - Pairing: Flashes twice per second
- Connected/Unconnected: Off
Indicator 3 (Red/Green)
- Bluetooth Channel 3 - Reconnecting: Flashes red once per second
- Bluetooth Channel 3 - Pairing: Flashes red twice per second
- Connected/Unconnected: Off
- Battery Level < 20%: Flashes red four times per second (when connected)
- Charging: Solid red
- Fully Charged: Solid green
Restore Factory Defaults
Hold esc + fn simultaneously for 3 seconds. The three indicators will blink 3 times, confirming the factory reset is complete.
Check Battery Level
Hold fn + alt + cmd simultaneously to check the battery level. The blinking frequency of the red battery indicator shows the level:
| Blinking Frequency | Battery Level |
|---|---|
| Once | 0-25% |
| Twice | 25%-50% |
| Three Times | 50%-75% |
| Four Times | 75%-100% |
Note: This function is only available when the keyboard is connected.
Charging
When the battery level is below 20%, the red battery indicator will blink. Recharge the keyboard using the included USB cable. Full charging takes approximately 2-3 hours. The battery indicator will be solid red while charging and turn solid green when fully charged.
Sleep Mode
The KB01104 enters sleep mode after 10 minutes of inactivity, which disrupts the Bluetooth connection. The connection can be re-established by pressing any key.
Product Specification
| Bluetooth Version | Bluetooth 5.3 |
| Bluetooth Range | 10 m |
| Charging Time | 2~3 h |
| Continuous Working Time | About 150 h |
| Operating Temperature | -10°C~+55°C |
| Bluetooth Frequency Range | 2402-2480MHZ |
| Actuation Force | 60±10g |
| Battery Capacity | 280mAh |
Packing List
- KB01104 Keyboard *1
- Charging Cable *1
- Instruction Manual *1
FCC Compliance
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The Grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance, as such modifications could void the user's authority to operate the equipment.
The device has been evaluated to meet general RF exposure requirements. This equipment complies with FCC's RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna(s) must not be co-located or conjunction with any other antenna or transmitter.
Battery Safety Warning
This product contains a built-in rechargeable lithium battery. Please observe the following safety precautions: Do not dismantle, hit, crush, or expose the battery to fire. If the battery experiences severe swelling, discontinue use immediately. Avoid placing the battery in high-temperature environments, and do not use it if it has been immersed in water. During transportation, do not mix the battery with metallic objects.
Charging Precautions
The power delivered by the charger must be between a minimum of [0.05] Watts (required by the radio equipment) and a maximum of [1.25] Watts to achieve the maximum charging speed.
Service Center / Contact Information
For support, please contact the relevant regional service center:
Europe
F&M Technology GmbH
Tel: +49 341 5199 8410 (Working day 8 AM - 4 PM CET)
Fax: +49 341 5199 8413
Address: Fraunhoferstraße 7, 04178 Leipzig, Deutschland
North America
Inateck Technology Inc.
Tel: +1 (909) 698 7018 (Working day 9 AM - 5PM PST)
Address: 2078 Francis St., Unit 14-02, Ontario, CA 91761, USA
Japan
Inateck 株式会社
電話番号: +81 06 7500 3304
〒547-0014 大阪府大阪市平野区長吉川辺3丁目10番11号
United Kingdom
Inateck Technology (UK) Ltd.
95 High Street, Office B, Great Missenden, United Kingdom, HP16 0AL
Tel: +44 20 3239 9869
Manufacturer
Shenzhen Inateck Technology Co., Ltd.
Address: Suite 2507, Block 11 in Tian An Cloud Park, Bantian Street, Longgang District, Shenzhen, Guangdong, China
Email: product@licheng-tech.com
Postal code: 518129
EC REP / UK REP
F&M Technology GmbH
For Product and Battery Fraunhoferstraße 7, 04178 Leipzig, Deutschland
Tel: +49 341 5199 8410
