Document Number: 2415972-03.2025
The Hilti HDA-T, HDA-TF, and HDA-TR anchors are designed for reliable fastening in concrete. This document provides essential specifications, installation instructions, and accessory compatibility information for the M10 and M12 anchor sizes.
The following table details the key specifications for the HDA-T/-TF/-TR anchors:
| Anchor Type | tfix min - max [mm] | df [mm] | hs [mm] | SW [mm] | Tinst |
|---|---|---|---|---|---|
| HDA-T/-TF/-TR | 10 – 20 | 21 | 2 – 6 mm (1/16" ... 1/4") | 17 | 50 Nm (37 ft-lb) |
| HDA-T/-TF/-TR | 10 – 30 | 23 | 2 – 7 mm (1/16" ... 1/4") | 19 | 80 Nm (59 ft-lb) |
| HDA-T/-TF/-TR | 10 – 50 | 23 | 19 | 80 Nm (59 ft-lb) |
Note on hs: The embedment depth (hs) is critical for anchor performance. For M10 anchors, hs should be between 2-6 mm (1/16" – 1/4"). For M12 anchors, hs should be between 2-7 mm (1/16" – 1/4").
| Anchor Type | Drill Bit | Setting Tool | Torque Wrench Setting |
|---|---|---|---|
| HDA-T/-TF/-TR M10 × 100/20 | TE-C-HDA-B 20 × 120 | TE-C-HDA-ST 20-M10 | TE 30 - (02) |
| HDA-T/-TF/-TR M12 × 125/30 | TE-C-HDA-B 22 × 155 | TE-C-HDA-ST 22-M12 | TE 30 - (03) |
| HDA-T/-TF/-TR M12 × 125/50 | TE 30 - (03) |
| Anchor Type | Drill Bit | Setting Tool | Torque Wrench Setting |
|---|---|---|---|
| HDA-T/-TF/-TR M10 × 100/20 | TE-Y-HDA-B 20 × 120 | TE-Y-HDA-ST 20-M10 | TE 50 - (03) |
| HDA-T/-TF/-TR M12 × 125/30 | TE-Y-HDA-B 22 × 155 | TE-Y-HDA-ST 22-M12 | TE 60 - (04) |
| HDA-T/-TF/-TR M12 × 125/50 | TE 60 - (04) |
To ensure optimal performance and safety, maintain the following minimum clearances when installing anchors:
Refer to specific project requirements and local building codes for exact values.
Drill a hole into the concrete substrate using a suitable Hilti hammer drill and drill bit. The hole must be perpendicular to the surface [ perpendicular-symbol 90° ]. An eye symbol with an exclamation mark [ attention-symbol ] indicates this is a critical step. Ensure the hole depth is appropriate for the anchor size and base material.
Thoroughly clean the drilled hole to remove all dust and debris. This is crucial for proper anchor performance. Use a Hilti cleaning brush and vacuum cleaner [ dust-extraction-symbol ]. A warning symbol [ warning-symbol ] highlights the importance of this step.
Insert the Hilti HDA anchor into the cleaned hole. The anchor should be inserted straight and fully seated. A red indicator on the anchor should be visible at the surface of the fixture.
Place the fixture (e.g., bracket, base plate) over the anchor. Insert the bolt through the fixture and into the anchor. A red arrow [ insertion-arrow ] indicates the direction of insertion.
Check that the embedment depth (hs) of the anchor is within the specified range for the anchor size (M10: 2-6 mm, M12: 2-7 mm). A detailed view shows the correct seating of the anchor and bolt, with a checkmark [ correct-symbol ] indicating proper installation. A forbidden symbol [ prohibited-symbol ] indicates incorrect depth or seating.
Using a suitable wrench, tighten the bolt. The installation torque (Tinst) is critical for secure fastening. A detail view shows the tightening process and a torque symbol [ torque-symbol ].
Dispose of any packaging materials responsibly [ trash-can-emoji ].
Using the specified wrench size (SW), apply the recommended installation torque (Tinst) to the bolt. This ensures the anchor is properly set and achieves its full load-bearing capacity. A diagram shows the torque wrench and the required torque value.
The product label includes the Hilti brand, model designation (e.g., TE XX 0X), compliance marks (CE, UKCA), and important safety information in Japanese: "Please read the instruction manual before use." [ attention-symbol ].
 |
Hilti HDA-T / -TF / -TR M16 Anchor Installation Guide and Technical Data Comprehensive installation instructions and technical specifications for the Hilti HDA-T / -TF / -TR M16 anchor system. Includes dimensions, accessory compatibility, and step-by-step visual guidance for proper mounting. |
 |
Hilti HDA-P/-PF M20 Anchor Installation Guide Step-by-step installation instructions for the Hilti HDA-P/-PF M20 anchor system, including technical specifications, required tools, and safety guidelines for proper and safe installation in concrete. |
 |
Hilti HDA Undercut Anchor: Technical Specification & Installation Guide The Hilti HDA Undercut Anchor is a post-installed concrete fastener designed for static, quasi-static, and fatigue cyclic loading. This European Technical Assessment provides comprehensive technical data, performance specifications, and installation guidelines for construction applications. |
 |
Hilti HDA Anchors: Declaration of Performance Declaration of Performance for Hilti HDA self-drilling anchors, detailing mechanical resistance, stability, and fire safety performance according to European standards. Includes product identification, intended use, manufacturer details, and declared performances for different HDA anchor types. |
 |
Hilti KB-TZ2 Wedge Anchor Installation and Specifications Guide for installing the Hilti KB-TZ2 wedge anchor (1/2" x 3"). Details installation steps, required tools, and technical specifications for concrete and CMU applications. |
 |
HILTI Anchor Fastening Technology Manual Comprehensive guide to HILTI anchor fastening systems, covering design, applications, technical specifications, and safety for mechanical, adhesive, and rail anchoring solutions. |
 |
Hilti HFB-R Anchor Installation Guide and Specifications Detailed instructions for installing Hilti HFB-R anchors, covering safety, specifications, dimensions, and step-by-step procedures for professional use. |
 |
Hilti HST3 and HST3-R M24 Wedge Anchor Installation Guide Comprehensive guide for installing Hilti HST3 and HST3-R M24 wedge anchors, covering drilling, anchor insertion, and final torque specifications for secure concrete fastening. |