Brother RJ-3150 Mobile Printer User's Guide

Unpacking the RJ-3150

Check that the package contains the following before using the printer:

• Printer
• Rechargeable Li-ion Battery
• Belt clip
• User's Guide
• Product Safety Guide
• Clock battery
• Phillips screw

General Description

The printer has the following components:

1 Battery compartment

2 Battery latch

3 USB host port

4 Mini-USB port

5 DC connector

6 Cover open lever

7 Peeler latch

8 RD Roll compartment cover

9 Paper outlet

10 Label peeler

11 LCD

12 BATT (Battery) indicator

13 (Power) button (To turn the printer on/off)

14 CANCEL button

15 Cursor button (UP/DOWN)

16 OK button

17 Menu button

18 (Feed) button (To feed the paper or print the printer settings)

Using the Rechargeable Li-ion Battery

Installing the Rechargeable Li-ion Battery

1. Make sure that the battery latch is lifted up, and then insert the battery into the battery compartment with the battery cover attached to the battery. Ensure the terminal end of the battery faces inward.
2. With the battery inserted and while pushing the battery lightly into the cavity, lower the battery latch until it clicks, locking the battery in place.

Removing the Rechargeable Li-ion Battery

While pushing the battery lightly, lift the battery latch to unlock the battery, and then remove the battery.

Turning the Printer On or Off

• On: Press and hold the [Power] button until the LCD display turns on.
• Off: Press and hold the [Power] button until the message "System Off" is displayed on the LCD display.

NOTE: Do NOT remove the battery or power to turn off the printer until the LCD display turns off.

Recharging the Li-ion Battery

1. Ensure the rechargeable Li-ion battery is installed in the printer.
2. Use the AC adapter and AC power cord to connect the printer to an AC power socket (see Connecting to an AC Power Outlet (Optional)), or use the car adapter to connect the printer to a DC power socket (see Connecting to a DC Power Outlet (Optional)).
3. The battery indicator light is orange when the battery is charging. When the rechargeable Li-ion battery is fully charged, the battery indicator light turns off. Disconnect the AC adapter or car adapter from the battery's DC connector.

For details, see the Online User's Guide.

Connecting to an AC Power Socket (Optional)

Connect the printer to a nearby AC power socket to charge the rechargeable battery.

1. Connect the AC adapter to the printer.
2. Connect the AC power cord to the AC adapter.
3. Connect the AC power cord to a nearby AC power socket (100 - 240 VAC, 50 - 60 Hz).

Diagram description: Shows an AC adapter connected to an AC power cord, which plugs into a wall socket.

Connecting to a DC Power Socket (Optional)

Connect the printer to your vehicle's 12 V DC power socket (cigarette lighter, etc.) to charge the rechargeable battery.

1. Connect the car adapter to the vehicle's 12 V DC power socket.
2. Connect the car adapter to the printer.

Diagram description: Shows a car adapter plugged into a vehicle's 12V socket and connected to the printer.

NOTE: A battery charger (option) and cradle (option) can also be used for charging.

Installing the Clock Battery

1. Open the battery cover using a Phillips screwdriver.
2. Insert the supplied battery into the space for the battery, making sure that the battery is level and its positive side is facing up.
3. Replace the battery cover.

Setting the Language of the LCD Display

Press the [Menu], [▲] (Up Arrow), or [▼] (Down Arrow) button to select the [Administration] menu, and then press the [OK] button. The default password is "1111". Select [#Language], and then press the [OK] button. Select a language, and then press the [OK] button.

Printing Receipts or Labels

1. Install the printer driver and software downloaded from the web page. (See Installing the Drivers section.)
2. Ensure the printer is powered using a charged battery.
3. Turn the printer on.
4. Connect the printer to a computer or handheld device using either a USB cable, Bluetooth, or Wi-Fi.
5. Insert the RD Roll.
6. Print receipts or labels.

For details, see the Online User's Guide.

Setting the RD Roll

When Not Using the Label Peeler

NOTE: You can also view information about loading paper in Help. While the printer is turned on, open the RD Roll compartment cover, and press the [Menu] button on the printer.

1. Push the cover open lever to open the RD Roll compartment cover.
2. Open the roll guides by lifting up the roll guide adjustment lever and pulling the roll guide outwards. Insert an RD Roll into the RD Roll compartment with the roll feeding from the bottom.
3. While lifting up the roll guide adjustment lever, push in both roll guides to the roll width. Insert the RD Roll so that it is positioned straight in the RD Roll compartment.
4. Close the RD Roll compartment by pressing down on the center of the cover until it latches.

Diagram description: Shows opening the cover, adjusting roll guides, inserting the roll, and closing the cover.

When Using the Label Peeler

NOTE: You can also view information about setting the label peeler and loading paper in Help. While the printer is turned on, open the RD Roll compartment cover, and press the [Menu] button on the printer.

A video on setting up the label peeler is available at: http://solutions.brother.com/movie/d532/

1. Push the cover open lever to open the RD Roll compartment cover.
2. Push both sides of the label peeler towards the rear of the printer. The peeler will move up and away from the printer. Then, fully pull out the peeler away from the printer until the marks on the peeler are visible.
3. Peel off the first label of the RD Roll. Then, insert the RD Roll so that the top edge of the second label is at the same height as the top edge of the media sensor plate.
4. Close the RD Roll compartment cover. Make sure the label peeler is on top of the cover.

IMPORTANT: Make sure that the labels are not pinched by the peeler rollers. The backing paper of the labels may not be peeled off.

5. In order to remove any slack in the roll, lightly pull on the paper fed out of the paper outlet until no more can be pulled out.
6. Push both sides of the label peeler until it clicks into place.

NOTE: To open the RD Roll compartment cover when the label peeler is set up, first release the peeler latches on both sides of the printer before pushing the cover open lever.

Diagram description: Shows opening the cover, adjusting the label peeler, inserting the roll with the peeler, and closing the cover.

Removing the RD Roll

1. Push the cover open lever, and then open the RD Roll compartment cover.
2. While pushing the roll release lever, tilt the roll guide slightly, and then remove the roll. The roll can be removed without changing the position of the roll guide.

IMPORTANT: Do not forcefully tilt the roll guide too far. Otherwise, the roll guide could break.

NOTE: When you use the label peeler, make sure that the backing paper does not become caught when removing the RD roll.

Diagram description: Shows opening the cover, releasing the roll, and removing the roll.

Attaching the Belt Clip

When using the printer outside the office, you can attach the included belt clip to the printer and secure the belt clip to your belt.

1. Secure the Phillips-head screws to the rear of the printer.
2. Attach the clip to your belt.

IMPORTANT: Make sure that the belt clip is attached securely to the printer and the wearer's belt. There is a risk of injury if the belt clip is not attached securely and the printer falls.

Diagram description: Shows attaching the belt clip to the rear of the printer with screws, and then attaching the clip to a belt.

Installing the Drivers

Please install the printer driver and P-touch Editor software before using the printer.

1. Visit the Brother website at http://www.brother.com/inst/ and download the installer for the software and documents.
2. Double-click the downloaded .exe file and follow the on-screen instructions to proceed with the installation. In the dialog box for selecting which items to install, select the necessary software.

Wireless Network Connections

Bluetooth Connection

IMPORTANT: In order for the printer and your Bluetooth-equipped computer or adapter to communicate, you must first pair the printer with the computer or handheld device using the Bluetooth management software.

1. Press the [Menu], [▲] (Up Arrow), or [▼] (Down Arrow) button to select the [Bluetooth] menu, and then press the [OK] button. Set [Bluetooth (On/Off)] to [On].
2. Use your Bluetooth management software to discover the printer. Bluetooth communication is now available.

Wi-Fi Connection

IMPORTANT: In order for the printer and your network access point or router to communicate, you must first install the printer driver and Printer Setting Tool.

1. Press the [Menu], [▲] (Up Arrow), or [▼] (Down Arrow) button to select the [WLAN] menu, and then press the [OK] button. Set [WLAN (On/Off)] to [On]. Wi-Fi communication is now available.

For details, see the Online User's Guide.

Battery Indicators

The BATT indicator shows the battery status:

• [Indicator Lit]: Indicator is lit
• [Indicator Blinking]: Indicator is blinking
• (Off): Indicator is off
• (Orange): Indicator is orange
• Example: ● [Indicator Blinking in Orange]

Maintaining the Printer

Maintenance of the printer may be carried out as required. However, some environments may require more frequent maintenance (e.g., in dusty conditions).

Print Head Maintenance

Use a dry cotton swab to wipe the print head.

Diagram description: Shows a print head being wiped with a cotton swab.

Roller Maintenance

Use a piece of cellophane tape or a lint-free cloth to remove dirt from the roller. After cleaning, ensure no lint or other material remains on the roller.

Diagram description: Shows cleaning a roller with tape or a cloth.

Paper Outlet Maintenance

If adhesive accumulates at the paper outlet and media becomes jammed, clean the paper outlet with a cloth slightly moistened with isopropyl alcohol.

Diagram description: Shows cleaning the paper outlet.

Printing the Printer Set-up Information

You can use the [Feed] button to print a report listing the following printer settings:

• Program version
• Printer usage history
• Missing dot test pattern
• Printer setting information
• List of transferred data
• Network setting information

NOTE:

• You can use the Printer Setting Tool to set in advance which items will be printed.
• The node name appears in the Printer Settings. The default node name is "BRWxxxxxxxxxxxx". ("xxxxxxxxxxxx" is based on your printer's MAC Address / Ethernet Address.)

1. Ensure a roll of 76.2 mm receipt paper has been loaded and the RD Roll compartment cover is closed.
2. Turn on the printer.
3. Press and hold the [Feed] button until the message "Printing" is displayed on the LCD display. The settings will print.

NOTE:

• To print the Printer Set-up Information, it is recommended to use 76.2 mm receipt paper.
• This operation can also be performed using the Printer Setting Tool.

For details, see the Online User's Guide.

Internet Addresses

• Brother Global Web Site: http://www.brother.com
• Brother Developer Center: http://www.brother.com/product/dev/
• For Frequently Asked Questions (FAQs), Product Support and Technical Questions, and Driver Updates and Utilities: http://support.brother.com/