GE Profile GEOSPRING Smart Hybrid Heat Pump Water Heater – 50-gallon, 120V, FlexCapacity
Dimensions and Installation Information
This water heater must be installed in accordance with these instructions, local codes, utility codes, utility company requirements or, in the absence of local codes, the latest edition of the National Electrical Code. It is available from some local libraries or can be purchased from the National Fire Protection Association, 1 Batterymarch Park, Quincy, MA 02169 as booklet ANSI/NFPA 70.
For complete information, see installation instructions packed with your water heater.
Power Requirements
Check the markings on the rating plate of the water heater to be certain the power supply corresponds to the water heater requirements.
Location
Locate the water heater in a clean dry area as near as practical to the area of greatest heated water demand. Long uninsulated hot water lines can waste energy and water.
NOTE: Because this unit draws in air from the room to heat the water, the room must be at least 10' x 10' x 7' (700 cubic feet) or larger. If the room is smaller, there must be a louvered door. Louvers should be 240 square inches (0.15m²) or greater. If two louvers are used, one should be near the top of the door. Place the water heater in such a manner that the air filter, cover and front panels can be removed to permit inspection and servicing, such as removal of elements or cleaning of the filter. The water heater and water lines should be protected from freezing temperatures and high-corrosive atmospheres. Do not install the water heater in outdoor, unprotected areas.
Dimensions:
- Height: 68 1/4"
- Width: 24"
Illustration intended for dimensional reference only. Refer to photograph for actual product appearance.
Front & Back Clearance Requirements
A 7" clearance is recommended with a minimum of 7" air space between any object and the front and back of the water heater and 7" on each side. Clearance is needed to allow for removal of the front and back covers in the event service is needed.
Top Filter Removal Clearance Requirements
A minimum 8" clearance is required at the top of the water heater to pull the filter up and remove it for cleaning. It is critical that the hot and cold water plumbing and the electrical connections do not interfere with the removal of the filter.
Condensate Drain Required
A primary drain pipe must be installed at the top right side of the water heater. The primary drain is intended to carry all condensate away.
Water Supply Connections
Refer to the illustration below for suggested typical installation. The installation of unions or flexible copper connectors is recommended on the HOT and COLD water connections so that the water heater may be easily disconnected for servicing if necessary. The HOT and COLD water connections are clearly marked and are 3/4" NPT on all models.
NOTE: Install a shut-off valve in the COLD water line near the water heater. This will enable easier service or maintenance of the unit later.
IMPORTANT: Do not apply heat to the HOT or COLD water connections. If sweat connections are used, sweat tubing to adapter before fitting the adapter to the COLD water connections on heater. Any heat applied to the HOT or COLD water connection will permanently damage the dip tube.
Illustration intended for dimensional reference only. Refer to photograph for actual product appearance.
Relief Valve discharge: 6" (15.2 cm) minimum from the floor
Installation Checklist
- Tank location: Room size requirements (10' x 10' x 7' or 240 sq. in. open-air-flow area). Back and side clearances (7"). Front clear. Ensure unit is level.
- Verify Air Filters: Ensure air filters are installed.
- Plumbing connections: No leaks after filling. Install shut-off valve and leak detect sensor.
- Condensate lines: Main drain line installed and directed to a drain or condensate pump.
- Temperature and pressure-relief valve: Valve is working and drain line completed per local code.
- Electrical: Verify 208/240 VAC or 120VAC connection. 120V units include a 10ft cord.
- Electrical connection: Does not prevent air filter removal.
- Control panel: Verify display shows 120°F (49°C) Hybrid mode. Assist user with temperature and mode adjustments.
- SmartHQ™ app: Download and connect appliance to WiFi/Bluetooth®.
Normal Startup – What to Expect After Pressing the Power Button
| Elapsed Time | Hybrid Electric Water Heater Actions | Comments |
|---|---|---|
| 0 to 3 minutes | Unit will go through self-check. Fan will turn on after 1 minute. | This 3-minute off-time prevents compressor damage. A clicking noise may be heard during startup. |
| 3 to 12 minutes | Compressor turns on. Fan continues to run. | This 9-minute period is used to ensure the tank is full of water (dry-fire prevention algorithm). If no water is detected, a F75 Fault code will be displayed. |
| 12 minutes and beyond | Compressor turns off (fan will run for 30 minutes after any compressor operation). Normal heating operation resumes. | The water heater is operating in Hybrid mode. Quickly provides initial amount of hot water with heating elements, then switches to efficient heat pump for majority of heating. |
NOTE: The heat pump operating range is 35°F to 120°F (2°C to 49°C). If the ambient temperature is outside of this range, the heat pump will turn off and the electric elements will be used until the ambient temperature returns to within the operating range.
Features and Benefits
- More Energy Efficiency: Amplifies ambient air into water-heating energy, exceeding ENERGY STAR® requirements.
- FlexCapacity: Electronic mixing valve blends hot and cold water for precise control, providing up to 60% more hot water (50-gallon unit performs like an 80-gallon).
- Homeowner Savings: Potential savings up to $550 on annual energy bills, plus eligibility for up to $900 in ENERGY STAR® and local utility rebates, and up to $2,000 in Inflation Reduction Act (IRA) tax credits.
- Total Control with SmartHQ™: Monitor, control, and adjust the water heater remotely via WiFi and the SmartHQ™ app. Receive alerts and track usage.
- Wireless Leak Detection with Automatic Water Shutoff: Wireless water sensor detects leaks and sends alerts via the SmartHQ™ app, automatically shutting off water in case of emergency.
- Dynamic Demand Response: Built-in EcoPort capabilities optimize home energy usage based on utility rates.
- Maximum Performance: Delivers 59 gallons in the first hour (DOE First-Hour Rating), ideal for high-demand homes.
- Flexible & Easy Installation: Installs easily with a 120V standard plug-in or can convert to 240V on a 20A dedicated circuit. Features integrated pocket handles and pre-installed wire connectors.
- Household Size: Suitable for households of up to five people on the X-High setting.
- Five Operation Modes: Heat Pump, Hybrid, High Demand, Electric, and Vacation modes for personalized water heating.
- 10-Year Limited Warranty: Covers tanks and parts for 10 years.
- Quiet Operation: Operates at a low 41 dBA for a peaceful home environment.
For answers to your Monogram, Café™, GE Profile™ or GE Appliances product questions, visit our website at geappliances.com or call GE Answer Center® Service, 800.626.2000.
GE Appliances: Shop for Home, Kitchen, & Laundry Appliances
