10W RF NFC Enabled LED Driver (Constant Current)
Important: Read All Instructions Prior to Installation
Function Introduction
This section provides a basic overview of the RF Dimmable Driver, showing its AC/DC power input and LED output connections.
Product Data
| Feature | Specification |
|---|---|
| LED Channel | 2 |
| DC Voltage | 3-42V, Max. 50V |
| Current | 100-500mA via NFC tool; Min. current gear lower to 0.1mA, default 250mA |
| Current Accuracy | ±3% (±1%@Certain full load) @ full load |
| Rated Power | Max. 10W |
| Voltage Range | 220-240VAC/220-240VDC |
| Absolute Voltage Range | 196-264VAC/196-264VDC |
| Frequency Range | 0/50/60Hz |
| Power Factor (Typ.) | > 0.95 @ 230VAC Full load |
| Total Harmonic Distortion | THD ≤ 15% (@full load / 230VAC) |
| Efficiency (Typ.) | > 75% @ 230VAC full load |
| AC Current (Typ.) | 0.1A Max. |
| Inrush Current (Typ.) | Max. 4.32A at 230VAC; 80µs duration |
| Leakage Current | <5mA/230VAC |
| Anti Surge | L-N:2KV |
| Dimming Interface | RF(Sub-G) |
| Dimming Range | 0.01%-100% @ Max current |
| Dimming Method | Amplitude/CCR dimming |
| Dimming Curve | Linear/Logarithmic optional |
Protection, Environment, Safety & EMC
| Category | Parameter | Value |
|---|---|---|
| Protection | Short Circuit | Yes, remove the fault conditions and re-power the device. |
| Over Current | Yes, remove the fault conditions and re-power the device. | |
| Over Temperature | Yes, remove the fault conditions and re-power the device. | |
| Environment | Working Temp. | -25°C ~ +45°C |
| Max. Case Temp. | Tc=85°C | |
| Working Humidity | 10% ~ 95% RH non-condensing | |
| Storage Temp. & Humidity | -40°C ~ +80℃, 10% ~ 95% RH | |
| Safety & EMC | Safety Standards | EN61347-1, EN61347-2-13, GB/T 19510.1-2023, GB/T 19510.213-2023 |
| Withstand Voltage | I/P-O/P: 3.75KVAC | |
| Isolation Resistance | I/P-O/P: 100M Ohms/500VDC/25°C/70% RH | |
| EMC | EMC Emission | EN55015, EN61000-3-2, EN61000-3-3, GB 17625.1-2022, GB/T 17743-2021 |
| EMC Immunity | EN61547, EN61000-4-2,3,4,5,6,8,11 | |
| MTBF | 191350H, MIL-HDBK-217F @ 230VAC full load and 25°C ambient temperature | |
| Others | Dimension | 101x36x25mm (L*W*H) |
| Warranty | 5 Years |
Key Features
- Dimmable LED driver. Max. output power 10W.
- 100-500mA current selectable via NFC program tool. Min. current gear lower to 0.1mA.
- Dimming curves/Target current/Power-on behavior settings via NFC program tool.
- Class II power supply, full isolated plastic case.
- High power factor and efficiency.
- Radio Frequency: Default 869.5/916.5 (1009 Version), Available 868/434mhz (2504 Version).
- Used to switch and dim Tunable White LED lighting fixtures.
- Amplitude/CCR dimming, smooth and deep dimming.
- Compatible with a variety of RF remotes.
- IP20 rating, suitable for indoor LED lighting applications.
- 5 years warranty.
Safety & Warnings
- DO NOT install with power applied to the device.
- DO NOT expose the device to moisture.
Pairing devices with RF remote
- Do wiring according to connection diagram.
- Pair RF Driver with RF remote: please refer to the instruction of the remote that you would like to pair with.
Working with "SR NFC Tool" APP
Step 1: Download and Open the APP
Search for "SR NFC Tool" on the App Store and Google Play, then open the app.
Step 2: Add Device
Tap "+" to add RF devices and name it as you wish.
Step 3: Unlock Device and Configure Parameters
Unlock the device to enter the parameter configuration page. Note: You must unlock the device before making settings. Only selected functions will display their interfaces.
Step 4: Set Parameters
Choose settings based on your requirements. Available dimming curves include DALI Standard and various logarithmic curves (Log gamma 1.0 to 4.6). You can also set Target Current, Power on state, and On/Off transition time.
Tips:
- NFC function does not require external power.
- Many functions can be configured via NFC.
- For best performance, use with the manufacturer's RF remotes.
- This is a 2-channel output product; ensure both loads are connected and have the same load for each channel during testing.
- For 1-channel fixtures, use the manufacturer's 1-channel drivers.
- Read instructions carefully before proceeding.
Wiring Diagram
Illustrates the wiring for a 4-wire CCT LED luminaire. Note that 3-wire CCT LED luminaries are also applicable.
Diagram Description:
The diagram shows the RF Dimmable Driver connected to the AC input (L, N) and the LED output (WW+, WW-, CCT LED). It also indicates connections for a CCT LED module.
Product Dimension
Diagram showing the physical dimensions of the LED driver: Length 101.0mm, Width 36.0mm, Height 25.0mm, with mounting hole details.
Operating Window
A graph illustrating the operating voltage range (U_LED (min), V to U_LED (max), V) against the output current (A).
Dimming Curve
A graph showing the relationship between Light Level and Output Current, demonstrating the dimming performance.
Driver Performance
Graphs displaying:
- Typical Power Factor: Power factor across different output currents (1.51A to 10.00A).
- Typical Efficiency: Efficiency percentage across different output currents (4.02A to 10.00A).
- THD VS Load: Total Harmonic Distortion percentage versus load percentage (50% and 100% load).
Expected Lifetime
A table detailing the expected lifetime of different module numbers (SRP-1009N, SRP-2504N) at various ambient temperatures (Ta) and case temperatures (Tc).
MCB Load Quantity
A table indicating the maximum quantity of LED drivers that can be connected per Miniature Circuit Breaker (MCB) type (B10, B13, B16, etc.), based on peak current (Ipeak) and width (Twidth).
Notes:
- MCB parameters are based on ABB S200 series circuit breakers. Quantities may vary with different brands/models.
- Do not exceed the specified quantity during installation.
- Environmental temperature and adjacent MCB installations may affect the load quantity.
- Type C MCBs are recommended for LED lighting.
Update Log
Details the update history, including date, version, update content, and updater. The initial version was released on 2024-7-26.
Quick Connector Box (Optional for Order)
SRP-Loopbox-01
Loop in & Loop Out design with wiring capability of 0.5-2.5mm² (AWG 14-20). Includes top and side view diagrams.
Note: A gasket may be needed for balance due to height differences between the 10W enclosure and the Loop box.
SRP-Loopbox-02
Plug & Play design (Wago Terminal) with wiring capability of 0.5-2.5mm² (AWG 14-20). Includes top and side view diagrams, and details on mating with Wago 770-1105/022-000.
Note: A gasket may be needed for balance due to height differences between the 10W enclosure and the Loop box.
Socket (770-1105/022-000) | WAGO USA
