Drive-Thru Systems User Manuals | Drive-Thru Repairs | HME
Installation Guide for HME models including: IB7000, SS7000, B7000 Drive Thru Wireless Intercom, B7000, Drive Thru Wireless Intercom, Thru Wireless Intercom, Wireless Intercom, Intercom
Drive-Thru Systems User Manuals | Drive-Thru Repairs | HME
R I HM ELECTRONICS, INC. 2848 Whiptail Loop, Carlsbad, CA 92010 USA Phone: 1-800-848-4468 Fax: 858-552-0172 Website: www.hme.com Email: support@hme.com
File Info : application/pdf, 3 Pages, 2.70MB
DocumentDocumentQuick Reference Installation Guide NEXEO | HDXTM IB7000 INTERFACE BOX The IB7000 is an interface box used to connect the loop, microphone, and speaker to a NEXEO® Base Station. TOOLS/EQUIPMENT REQUIRED · Screwdriver/Wrench for opening speaker post. · Wire Strippers, cutters, and other standard tools used for terminating cables/wires. · Audio Cable (not included) INSTALLATION AND SETUP Fig. 3 shows how the IB7000 is typically connected. Adhesive strips on the housing allow the IB7000 to be affixed to a clean, dry surface inside the speaker post. Note: The IB7000 must be mounted vertically, inside the speaker post, close to the speaker/microphone. This will help minimize audio hum and noise. The IB7000 power LED illuminates green when it is connected to a powered on base station. The max IB7000 cable length to guarantee operation at max volume should not exceed 500 ft (152 m). Fig. 1 · The two-pin Loop connector connects to the ground loop detector. · The three-pin PLC/BASE connector connects to J4500 on the base station. This connection requires the shield/drain to be grounded; see Table 1. · The seven-pin DM5 MIC | SPKR connector connects to the Microphone and Speaker; see Table 2. · The five-pin RELAY | BCKP SPKR connector (optional) connects to an intercom system like the IC300 if a backup is needed in the event of a system failure. Fig. 2 Connector Side IB7000 DM5 MIC | SPKR connector NEXEO Base Station J4500/J4501 (Spkr/Mic Intrfc) Pin # Label Description/wire color Pin # Label to IB7000 PLC/BASE 1 Mic + Ext. Microphone positive (Red) 1 Spkr/Mic PL + IN1/PL+ (Red wire) 2 Mic - Ext. Microphone negative (Black) 2 Spkr/Mic PL - IN2/PC- (Black wire) 3 GND Mic Shield (must be terminated) 3 Shield GND - (Shield/drain) 4 I.D. 1-WIRE I/F (Red) for SS7000 only 4 Spkr/Mic PL + 5 GND Ground (Black) for SS7000 only 5 Spkr/Mic PL - 6 Spkr - Speaker negative (White) 6 Shield Table 1 7 Spkr + Speaker positive (Green) Table 2 HM ELECTRONICS, INC. 2848 Whiptail Loop, Carlsbad, CA 92010 USA Phone: 1-800-848-4468 Fax: 858-552-0172 Website: www.hme.com Email: support@hme.com HME# PUB-00073 Rev H 2/24/25 NOTE: Shield must be terminated to GND and insulated or sleeved IB7000 REAR VIEW Power LED PLC/BASE 1 1 2 3 HME LOOP 1 1 2 LOOP CONNECTION SS7000 SPEAKER REAR VIEW 1 2 3 45 HME Note: If using an SP10 speaker, only 2 speaker wires are used IN 1 - 1 IN 2 - 2 GND- 3 POS - 1 NEG - 2 BK SPKR + BK SPKR GND I.D. N.C. SPKR (+) - 7 SPKR (-) - 6 GND - 5 I.D. - 4 GND - 3 MIC (-) - 2 MIC (+) - 1 BK SPKR (+) - 5 BK SPKR (-) - 4 NO COM NC - 3 - 2 -1 1 1 2 3 45 | RELAY BCKP SPKR 1 2 3 45 6 7 | DM5 MIC SPKR DM5 MIC Insulate and ground exposed shield wires J?300 Micro USB J200 USB J4501 1 J4500 PCBA J3000 J803 J2003 Serial Debug 1 J804 1 123456 J1400 Ethernet Remote J3200 XCVR 4 J3400 Remote XCVR 3 J3600 Remote XCVR 2 Remot Fig. 3 To NETWORK ROUTER For CLOUD CONNECTION To REMOTE TRANSCEIVER REAR Base Station Opened with PCBA detail INSTALLING THE WEATHER COVER The IB7000 Weather Cover must be installed onto the IB7000 to protect the electrical connections from corrosion due to water/moisture ingress. (Even when installed in a speaker post or menu board, these locations do not guarantee a sheltered environment for the IB7000.) When installed, the top of the weather cover completely seals the IB7000 on top to prevent water or moisture ingress. The bottom has an opening to allow all the IB7000 cables to exit beneath the IB7000 once the cover is in place. Note: The cover must be oriented and installed the correct way to be effective (see Fig. 4). 2 IB7000 Weather Cover IN 1 - 1 IN 2 - 2 GND- 3 POS - 1 NEG - 2 IB7000 REAR VIEW PLC/BASE 1 1 2 3 HME LOOP 1 1 2 SPKR (+) - 7 SPKR (-) - 6 GND - 5 I.D. - 4 GND - 3 MIC (-) - 2 MIC (+) - 1 BK SPKR (+) - 5 BK SPKR (-) - 4 NO COM NC - 3 - 2 -1 THIS SIDE UP HME THIS COVER MUST BE INSTALLED 1 1 2 3 45 | RELAY BCKP SPKR 1 2 3 45 6 7 | DM5 MIC SPKR NOTE: When attaching weather cover, observe orientation label on cover. Cables are bundled to exit opening at the cover bottom. Fig. 4 © 2025 HM Electronics, Inc. All rights reserved. 1. Orient the weather cover correctly before installing (see the up arrow on the cover rear, Fig. 4 & 5). 2. Attach the cover by first placing the top latch over the ridge and housing seam of the IB7000 (Fig. 6). 3. Then, hinge the bottom part of the cover onto the bottom part of the IB7000. If there is resistance, the bottom latches are flexible and can be pried onto the IB7000 (Fig. 6). 4. Verify all the IB7000 cables exit through the opening at the cover bottom before pressing in on the cover to close. The cover will snap securely into place (Fig. 7). Note: To remove the cover, do so in reverse order to the above steps. First, use your fingers to pry the flexible latches on the cover bottom as you detach it from the IB7000 ridge and housing seam it is gripping. Hinge outward away from the IB7000 until the top freely detaches. WEATHER COVER 1 SIDE VIEW IB7000 SIDE VIEW 2 Rigid Top Latch Ridge and housing seam THIS SIDE UP Flexible Bottom Latches Opening for cables to exit Fig. 5 TECHNICAL SPECIFICATIONS Flex Latches 3 Fig. 6 4 Fig. 7 IB7000 Dimensions (IB only) 5.68" H x 5.68" W x 2.05" D (144.3 x 144.3 x 52.1 mm) Dimensions (Cover only) 6.79" H x 5.85" W x 2.22" D (172.3 x 148.6 x 56.4 mm) Dimensions: IB with Cover 6.79" H x 5.85" W x 2.83" D (172.3 x 148.6 x 71.6 mm) Weight: IB with Cover 19.2 oz (543 g). IB = 14.4 oz (408.2 g), cover = 4.8 oz (135 g) Power Supply Voltage: 48 VDC (powered from BS7000) Current: 0.331 A (max start up) Frequency Range Audio: 100 Hz to 7.4 kHz Powerline network over 48 VDC: 2 MHz 67.5 MHz Power Nominal power with no audio: 5.2 W Maximum power at maximum volume: 22 W Front Panel Two adhesive strips for mounting to a vertical surface Rear Panel Phoenix connector type headers (includes speaker output and analog DM5 microphone input) Wireless N/A Temperature Operating Temperature range: -25°C (-13°F) to +60°C (+140°F) Compliance See NEXEO | HDX - Regulatory, Compliance, and Safety Guide online A copy of this guide and additional information can be found under NEXEO | HDX by scanning this QR code or going to: https://www.hme.com/qsr/drive-thru-user-manuals/ The HME logo and product names are registered trademarks or trademarks of HM Electronics, Inc. © 2025 HM Electronics, Inc. All rights reserved. 3