VEVOR

Introduction

For your information, please read these installation instructions before using your Retractable Hose Reel. Please keep all instructions and refer to them when necessary.

⚠️ Do not leave the tap on - turn tap off after use and release excess pressure before retracting back into housing.

Overview

Image of the VEVOR Retractable Hose Reel, showing the main housing, hose, spray gun, wall bracket, and mounting hardware. Parts are labeled a-l.

• a. Mounting Tube
• b. Hexagonal Coach Bolts
• c. Wall Plugs
• d. 180° Wall Bracket
• e. Garden Hose
• f. Tap-to-Reel Hose
• g. Multi-Function Spray Gun
• h. Housing
• i. Hose Connectors
• j. Universal Tap Adaptor (copper joint for US)
• k. Stopper
• l. Inspection opening

Spare Parts

Images of spare parts:

• Wall plugs + Hexagonal Coach bolts + securing pin + seal ring
• 9-function spray gun
• Mounting Tube
• Metal bracket

⚠️ Do not dismantle the Hose Reel for additional spare parts. Other internal metal parts can cause injury if tampered with. These parts are not available for replacement.

Installation

Your Retractable Hose Reel should be installed nearest to your chosen water source for convenience of use.

1. Check the TAP-TO-REEL HOSE can reach your tap prior to installing the WALL BRACKET.
2. Take the WALL BRACKET and place it against either a wall or wooden post.
3. Mark inside the centre of each of the bracket holes to prepare for drilling.
4. If you are attaching your Hose Reel to a wooden post, you will not require the WALL PLUGS as the COACH BOLTS can screw directly into wood.
5. Use the table below to select the correct drill bit for your Hose Reel.
6. If using plugs that were not included with your Hose Reel, drill slightly undersize as masonry materials all have different properties which will ensure the wall plugs have a secure fit. It is very important to use the correct size drill bit, so a very secure fit of the wall bracket is made before installing the Retractable Hose Reel.
7. When ready, drill all four holes, then hammer the WALL PLUGS gently into your wall (if attaching to a wall).
8. Place the WALL BRACKET in position over the four WALL PLUGS and screw each HEXAGONAL COACH BOLT into your wall or wooden post.
9. Screw in each HEXAGONAL COACH BOLT until all four have a secure hold on the bracket against the surface.
10. Take your Retractable Hose Reel, and remove the securing pin at the base of the MOUNTING TUBE.
11. Remove the MOUNTING TUBE from the Hose Reel and slot it over the WALL BRACKET. Align the holes in the HOUSING with the holes in the WALL BRACKET.
12. Insert the MOUNTING TUBE back into the holes on the WALL BRACKET and HOUSING. Then replace the securing pin in the base of the MOUNTING TUBE.
13. Connect your TAP-TO-REEL HOSE to your garden tap.

Diagram illustrating the installation of the wall bracket. It shows marking holes, drilling, inserting wall plugs, and attaching the bracket with hexagonal coach bolts. A table provides drill bit sizes for plugs, masonry, wood, and bolts.

Diagrams showing the process of mounting the hose reel onto the installed wall bracket using the mounting tube and securing pin. An image shows the hose connected to a garden tap.

Product Parameters

Care and Troubleshooting

How far can I pull out the GARDEN HOSE?

You will find an indication sticker 1 meter before the maximum length.

⚠️ Do not pull the hose past this point.

Close-up image of the garden hose with 'STOP!' stickers indicating the maximum pull-out length.

How do I properly retract the GARDEN HOSE?

When walking the GARDEN HOSE back to the HOUSING, turn off the tap, press the lever on the watering gun to release the water pressure in the hose. This makes the retraction of the GARDEN HOSE a lot easier and prolongs the life of your Hose Reel.

Why is my fully extended GARDEN HOSE not retracting?

If the GARDEN HOSE retraction wheel is stuck and the GARDEN HOSE is fully extended, the wheel still has moved past this point. Grip the GARDEN HOSE close to the guide hole and gently pull.

The retraction wheel will give you enough movement to unlock itself before you slowly allow the auto retraction wheel to wind the GARDEN HOSE back into the unit.

Image of the multi-function spray gun in use, spraying water.

Warnings

• ⚠️ Do not leave the water turned on with the hose under pressure when not in use.
• ✔️ Always turn the water off and draw the water from the hose after use.
• ⚠️ Do not attempt to pull the hose reel apart.
• ⚠️ Do not pull the GARDEN HOSE to start retraction and let go of the hose. Always guide the GARDEN HOSE back to the housing.

Manufacturer Information

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu803nong11hao1602A-1609shi,baoshanqu, shanghai200000CN.

ECREP: E-CrossStuGmbH.

Address: MainzerLandstr.69,60329FrankfurtamMain.

UKREP: YHCONSULTINGLIMITED.

Address: C/OYHConsultingLimitedOffice147, CenturionHouse,LondonRoad, Staines-upon-Thames,Surrey, TW184AX

Imported to AUS: SIHAOPTYLTD.

Address: 1ROKEVASTREETEASTWOODNSW2122Australia

Imported to USA: SanvenTechnologyLtd.

Address: Suite250,9166AnaheimPlace, Rancho Cucamonga, CA91730