SHOWLITE DMX Master Pro USB Operators Manual & Lighting Accessories

SHOWLITE DMX Master Pro USB

ArtNr.: 00028353
Version: 04-2012

Features

• 192 DMX512 channels, DMX512 standard signal output
• Controls 12 lights, each with 16 channels
• 30 banks of 8 programmable scenes
• 6 chases of 240 programmed scenes from banks
• Data displayed by LCD
• Voice sensitivity adjustable
• 8 or 16 channels per light
• DMX channel reversal, data display in percent or numerical mode
• Pan and Tilt jog wheels for scanner control
• Sliding channel for X/Y or all channel mode
• MIDI control over banks, chases, and Blackout
• RDM for remote DMX address control
• Data copy via USB disk, software promotion via USB
• Support FAT 16/32 file layout

General Instructions & Safety Warnings

⚠️ WARNING: DO NOT allow inflammable liquids, water, or metal objects into the unit. If liquid is spilled, disconnect power immediately. STOP using the unit for serious problems and contact your dealer. DO NOT open the unit; no user-serviceable parts inside. NEVER attempt self-repair.

⚠️ CAUTION: Check for damage after unpacking. Do not use if in doubt. Keep packaging away from children. For adult use only. NEVER use in humid, vibrating, or extreme temperature conditions (below 2°C/35.6°F or above 45°C/113°F). Protect from excessive dryness/humidity (35%-80% ideal). DO NOT dismantle or modify.

Panel Description

Front View

The front panel features:

• Scanner Buttons (1-12): Control 12 scanners, each with 16 DMX channels and fader control. LEDs indicate status.
• Scene Buttons: Load or store up to 240 programmable scenes.
• Faders (8): Control intensity for channels 1-8 or 9-16 depending on the selected page.
• Page Select Button: Switches between Page A (channels 1-8) and Page B (channels 9-16).
• Fog Machine Button: Activates fog machine.
• Speed Slider: Adjusts chase speed (0.1 sec to 10 min).
• Fade Time Slider: Adjusts transition time between scenes (0 sec to 30 sec).
• LCD Display: Shows current activity or programming state (max 2x8 characters).
• Pan Jog Wheel: Controls pan movement.
• Tilt Jog Wheel: Controls tilt movement.
• Program Button: Activates Program mode.
• MIDI/Rec Button: Controls MIDI operation or records programs.
• Auto/Del Button: Activates Auto mode or deletes scenes/chases.
• Music/Bank Copy Button: Activates Music mode or copies a bank of scenes.
• Bank Up/Down Buttons: Select from 30 banks.
• Tap/Display Button: Creates a beat or changes value mode (0-255).
• Blackout Button: Momentarily pauses output; holding enters Stand Alone mode.
• Chase Buttons (1-6): Activate programmed chases.
• Fine Button: Increases precision of Pan/Tilt control.
• Mode Button: Activates Assign or Reverse mode when pressed with Fine button.

Back Side View

The back panel includes the following ports:

• 1. USB: USB port for data transfer and software updates.
• 2. AUDIO IN: 0.1-1 Vp-p input.
• 3. MIDI IN: Receives MIDI data (5-pin connector).
• 4. DMX Polarity Select: Used to select DMX polarity.
• 5. DMX OUT: DMX signal output (XLR).
• 6. FOG MACHINE: Connector for fog machine.
• 7. DC INPUT: Power input (DC 9-12V, 300mA min).
• 8. POWER: On/Off switch.

Operation Guide (Summary)

The DMX Master Pro USB allows programming of scenes, chases, and programs. Key operations include:

• Programming Scenes: Enter Program mode, select scanner, adjust faders/jog wheels, set DMX channels (Page A/B), tap [MIDI/Rec] to store, select bank, tap scene button.
• Scene Editing: Program enable, select bank, select scene, make adjustments with faders/jog wheels, tap [MIDI/Rec], tap scene button to overwrite.
• Scene Copy: Program enable, select source bank/scene, select destination bank, tap [MIDI/Rec], tap scene button.
• Delete Scene: Program enable, select bank, press and hold [Auto/Del], tap scene button.
• Delete All Scenes: Turn off power, press and hold [Auto/Del] and [Bank Down], turn on power, wait for LEDs to flicker, then release.
• Bank Copy: Program enable, select source bank, tap [MIDI/Rec], select destination bank, tap [Music/Bank Copy].
• Editing Programs: Program enable, select chase button, select scene, tap [MIDI/Rec] to enter program mode, repeat steps to add up to 240 steps.
• Adding Steps to Program: Program enable, select program, press [Tap/Display], select place with [Bank Up/Down], tap [MIDI/Rec], press [Tap/Display], select scene with [Bank Up/Down].
• Deleting Program Steps/Programs: Follow specific procedures using [Auto/Del] and other buttons.
• Channel Assign/Reverse: Use [Mode] and [Fine] buttons to switch between assign and reverse modes. Select scanner, set 8/16 channel mode, select page (A/B), and assign/reverse channels.
• Glide Mode Select: Turn off power, press and hold [Mode] and [Tap], turn on power. Tap [Tap] to switch slide modes.
• Examine Assign/Reverse: Use [Mode] and [Fine] to enter examine modes, then select scanner.
• Starting Up Display Information: Specific button combination to set up display information.
• Running Scenes/Chases: Manual, Auto, and Music modes are available. Adjust wait time and fade time.
• MIDI Operation: Set up MIDI channel and address. MIDI form details note numbers for banks and chases.
• USB Function: Write data to USB-Stick, read data from USB-Stick, and update software via USB.
• RDM Operation: Discover equipment, set DMX addresses remotely.
• Turn Off Operation Condition: Save or discard settings upon power off.

Technical Specifications (DMX Master Pro USB)

• Power Input: DC 9V, 300 mA min.
• DMX Output: 3-pin male XLR
• USB: USB-A
• MIDI Signal: 5-pin standard interface
• Audio Input: Built-in microphone or line in
• Dimensions: 482x134x73mm
• Weight: 2.0 kg

SHOWLITE LS/LTS Light Stands

ArtNr.: 00028057, 00028059, 00046292

These light stands are designed for supporting lighting equipment.

Safety Instructions

• Not children's toys; not recommended for children under 3 years.
• Do not use as a tool or step ladder.
• Maximum load capacity: 30 kg (00028057) or 50 kg (00028059, 00046292) (centric load).
• Ensure legs are spread wide enough to prevent tipping. Use on a level, firm surface.
• For T-bar stands, ensure even weight distribution on both sides.
• Visually inspect for mechanical wear (deformed tubes, chipped clamps, worn rivets) before use. Do not use damaged stands.
• Keep limbs clear during setup to avoid pinching.

SHOWLITE Flood Light Panel

Model: 144x10mm LED RGBW
Art.Nr.: 00039189
Version: 05/2015

Technical Data

Preset Programs

DMX512 Channel List

Safety & Installation

General Precautions: Follow basic safety rules to avoid electrical shock, damage, fire, or other hazards. Use correct voltage. Inspect power cords. Do not place cords near heat sources or where they can be damaged. Unplug when not in use or during storms. Handle plugs carefully. Ensure adequate distance between AC adapter and device. Do not cover adapter. Use high-quality batteries, do not mix types, do not recharge non-rechargeables, observe polarity, do not short circuit, open, or incinerate batteries. Children should not handle batteries. Remove batteries for long-term storage. Dispose of batteries as special waste.

Location: Ensure AC outlet is accessible. Do not expose to excessive dust, vibration, extreme temperatures, or direct sunlight. Do not place in unstable positions. Do not block vents; ensure adequate ventilation to prevent overheating. Do not use near TVs, radios, or other electronic devices to avoid interference.

Connections & Handling: Turn off power for all devices before connecting. Set volume to minimum before turning power on/off. Avoid prolonged use at high volumes. Do not rest weight on the device, place heavy objects on it, or use excessive force on controls.

Do not open: The device contains no user-serviceable parts. Discontinue use and seek qualified service if malfunctioning.

Water Warning: Do not expose to rain, use near water, or in damp conditions. Never handle plugs with wet hands.

If abnormality noticed: If cord/plug is frayed/damaged, or if unusual smells/smoke appear, immediately turn off power, disconnect plug, and have device inspected.

Installation: Designed for floor or overhead rigging. Follow safety instructions (EN 60598-2-17, national standards). Overhead rigging requires authorized and experienced personnel. Use safety bonds and quick links compliant with DIN 56927, shackles with DIN EN 1677-1, and BGV C1 carbines. Installation must withstand 10x weight for 1 hour. Maximum drop distance 20 cm. Do not use damaged safety bonds.