SHOWLITE SPS-121 LED Spot
Smart Party Spot 12x1W LED
Specifications: 3R/3G/3B/3W LEDs, 25° Beam angle, Power: 230V-AC 50/60Hz - 12W, ArtNr 00046913
Important Safety Instructions
- Keep the unit away from heat sources, direct sunlight, humidity, water and any other liquids.
- Do not operate the unit if it has been exposed to water, moisture or any other liquids to prevent against electric shock, explosion and/or injury to yourself and damage to the unit.
- Do not use the unit if it has been dropped or damaged in any way.
- Repairs to electrical equipment should only be performed by qualified staff (electricians). Improper repairs may place the user at serious risk.
- Do not use the unit with wet hands.
- Do not put objects into any of the openings.
- Keep the unit free from dust, lint etc.
- Do not use this unit for anything other than its intended use.
- Keep the unit out of reach of small children. This product is not a toy.
- Do not use chemical cleaning solvents to clean.
- Do not open the device.
- For cleaning only use soft and dry cloth.
Getting Started
Unpack the LED spot & accessories and remove all packaging from the spot. Check if the spot and accessories are not damaged.
In the Box
- SPS-121 Party Spot incl. bracket and fixing screws.
- Instruction manual
Installation
The Showlite LED Spot is designed as floor effect or for overhead rigging on stages, in discotheques, theatres, etc. During installation consider all necessary safety instructions especially EN 60598-2-17 and national standards. Please note: for overhead rigging in public or industrial areas, a series of safety instructions have to be considered. This manual can only give a survey and does not list complete instructions. Installation must only be done by authorized and experienced operators.
Power Connection and DMX
After safe installation (floor or overhead) please connect the power cable to specified net voltage. You can operate the lighting device by an external DMX controller or by internal preset programs. If using a DMX controller connect the controller DMX-OUT with the lighting DMX-IN. To connect several lighting effects set up a DMX loop by connecting DMX-OUT of first device with DMX-IN of second device and so on.
DMX Connectors:
- DMX-IN: [DMX IN XLR Male]
- DMX-OUT: [DMX OUT XLR Female]
- Pinout: 1) ground, 2) signal (-), 3) signal (+)
Operation
All parameter settings and preset programs can be changed and selected on the backside operator panel. After first power on the display shows Addr A001. By pressing [ENTER] button, the display shows selected DMX address. By pressing [UP]/[DOWN] you can adjust the address and save with [ENTER] button. Display is showing AXXX (XXX = selected DMX address). By pressing [UP]/[DOWN] buttons you can select the other menus Chnd (DMX), SoUn, AUto, Colo, SLAv and ver. Select a menu and press [ENTER], display will change to parameter menu where you can change the particular parameter settings by pressing [UP]/[DOWN]. Parameters can be changed and saved by [ENTER] button.
Preset Programs: Select Auto or SoUn menu by pressing [UP]/[DOWN] and accept by pressing [ENTER]. The display will change to preset programs to be selected by [UP]/[DOWN]. By pressing [ENTER] you step into sub menu where you can adjust speed SP1 to SP9. In the Sound mode, the spotlight is controlled by the built-in microphone.
Display and Controls: [Digital Display: 8.8.8.8] with [MENU], [UP], [DOWN], [ENTER] buttons.
Menu Structure: Navigate through main menu items like Addr (DMX Address), Chnd (DMX Channel Mode), SoUn (Sound Mode), AUto (Auto Mode), Colo (Color Mode), SLAv (Slave Mode), and ver (Version). Select a menu with [ENTER] to adjust parameters using [UP]/[DOWN] and save with [ENTER].
DMX Channels
You can operate the device in 4 or 7 channel mode, please select mode in Chnd menu.
4-Channel Mode
| Channel | Value | Function |
|---|---|---|
| CH 1 | 0-255 | Red (0%-100%) |
| CH 2 | 0-255 | Green (0%-100%) |
| CH 3 | 0-255 | Blue (0%-100%) |
| CH 4 | 0-255 | White (0%-100%) |
7-Channel Mode
| Channel | Value | Function |
|---|---|---|
| CH 1 | 0-255 | Master dimmer (0%-100%) |
| CH 2 | 0-255 | Red (0%-100%) |
| CH 3 | 0-255 | Green (0%-100%) |
| CH 4 | 0-255 | Blue (0%-100%) |
| CH 5 | 0-255 | White (0%-100%) |
| CH 6 | 0-255 | Adjust Strobe (CH 6<16), adjust speed (CH 6>95) |
| CH 7 | 0-255 | See detailed function list below |
CH 6 Detailed Functions:
- 0-15: Dimmer
- 16-31: Color mixing plus change 1
- 32-47: Color mixing plus change 2
- 48-63: Color mixing plus change 3
- 64-79: Color mixing plus change 4
- 80-95: Color mixing plus change 5
- 96-111: Color sync strobe
CH 7 Detailed Functions:
- 112-127: Color fade
- 128-143: Color sync
- 144-159: Colors mixing & change then Shuter closing
- 160-175: down-dimming plus color change
- 176-191: Up-dimming plus color change
- 192-207: Color Up-dimming then down-dimming
- 208-223: Color mix change
- 224-239: Run sound mode 1
- 240-255: Run sound mode 2
Manufacturer and CE Conformity
Musikhaus Kirstein GmbH
Bernbeurener Str. 11
86956 Schongau/Germany
www.kirstein.de
CE Conformity
The CE-marking on your product and/or packing resp. user manual confirms the compliance of the product with all for this item related harmonized EC directives. You can download the EC declaration of conformity for this item under the download link below:
http://www.kirstein.de/docs/Konformitaetserklaerung/CE_Konformitaetserklaerung_000xxxxx.pdf
Please replace the placeholder "xxxxx" by the last 5 digits of the product article number.
??
