Progress Lighting 16" LED Linear Vanity

Package Contents

The package should contain the following items:

Hardware Contents (not actual size)

• [Part AA] Back plate: Comes assembled to canopy. Quantity: 1.
  (Diagram description: A circular metal plate with mounting holes and a central opening for wiring.)
• [Part BB] Wire nuts: Used for connecting electrical wires. Quantity: 3.
  (Diagram description: Small plastic connectors for joining electrical wires.)
• [Part CC] Flat head screws: Used for assembly. Quantity: 3.
  (Diagram description: Standard flat-head screws.)

Safety Information

Please read and understand this entire manual before attempting to assemble, operate, or install the product.

CAUTION: Read instructions carefully and turn electricity off at the main circuit breaker panel before beginning installation.

CAUTION: Risk of fire. Minimum 90°C supply conductors required. Consult a qualified electrician to ensure the correct branch circuit conductor.

WARNING: If any Special Control Devices are used with this fixture, follow instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electrical contractor.

CAUTION: All glass is fragile. Use care when handling glass shades and bulbs.

THIS PRODUCT MUST BE INSTALLED BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED, IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE.

KEEP THESE INSTALLATION INSTRUCTIONS.

(Note: Safety and installation warnings are also provided in French and Spanish in the original document.)

FCC Compliance: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

Preparation

1. Before beginning installation, make sure all parts are included using the contents diagrams from page 1. If any part is missing or damaged, do not attempt to assemble, install, or operate the product.
2. Estimated assembly time: 30 minutes.
3. Tools required for assembly (not included): Phillips screwdriver, pliers, wire stripper, safety glasses, electrical tape, ladder.

Care and Maintenance

Shut off main power supply before cleaning the product or changing light bulbs. To clean, wipe with a damp cloth. Do not use abrasive cleaners or cleaners that contain alcohol.

Assembly Instructions

Step 1: Mount Back Plate

The back plate [Part AA] comes assembled inside the canopy. First, detach the back plate from the canopy by removing the screws [Part CC]. Make sure to save these screws for step 3.

Then, attach the back plate onto the outlet box using the mounting screws supplied with the outlet box (not included).

(Diagram description: Shows the back plate [AA] being detached from the canopy by removing screws [CC]. Then shows the back plate being mounted to an electrical outlet box.)

Step 2: Connect Wiring

Strip 3/8" of insulation from the electrical wire ends.

Using wire nuts [Part BB], connect the white fixture wire to the white supply wire from the outlet box. Connect the fixture black wire to the black supply wire.

Connect the fixture ground wire and supply ground wire using a wire nut or by fastening to the ground screw on the back plate.

Push all wire connections into the outlet box.

(Diagram description: Illustrates electrical wiring. Shows stripped ends of white and black wires from the fixture being connected to corresponding white and black supply wires using wire nuts [BB]. Also shows the ground wire connection.)

Step 3: Attach Fixture

Attach fixture [Part A] to back plate [Part AA] using flat head screws [Part CC] to secure tightly.

(Diagram description: Depicts attaching the fixture [A] to the back plate [AA] using flat head screws [CC].)

Step 4: Select CCT Setting

Use the CCT switch to select either the 3000K, 4000K, or 5000K setting.

(Diagram description: Shows a close-up of a switch labeled "COOL", "WARM", "3000K", "4000K", "5000K" with an arrow indicating selection.)