VIMAR 692U / 692U/C Video Intercom Camera Units

Product Overview

The VIMAR 692U is a B/W camera unit with an external unit, while the 692U/C is a color camera unit with an audio external unit. Both models are designed for installation on VIMAR 8100 series entrance panels.

Technical Features

• Sensor: 1/4" CCD
• Lens: 3 mm fixed focus
• Lighting Control: Automatic
• Video Signal: Standard CCIR 625 lines, 50 fields (B/W) / PAL (Color).
• Operating Temperature: -5°C to +50°C
• Illumination: Infrared for B/W, white light for Color. Name-tag illumination via LEDs.
• Audio: Built-in external unit speech unit.
• Connection: Removable terminal block.
• Local Door Lock Release: Adjustable timing (1-30 sec) via panel trimmer.
• Power Supply: Bus powered.
• Dimensions: Max 80x120x25mm.
• Indicators: "Occupied-Wait" message.

Camera Adjustments

Adjustments on the back of the camera:

• External Volume: Trimmer adjustment.
• Camera Activation Time: Trimmer adjustment for Call, Conversation, Self-Start modes.
• Lock Activation Time: Trimmer adjustment (1-30 seconds).

Camera Time Settings

Time Ratios: Self-Start = 1/6 Conversation; Call = 1/4 Conversation.

Installation

Installation phases:

1. Install entrance panel.
2. Wire cables.
3. Connect external unit to system.
4. Program external unit.

Note: Connect terminal block only after wiring (green, black, white) to the panel.

Panel Dimensions

Approx. 200mm (H) x 101mm (W) x 38mm (D).

Component Identification

• A: Front plate
• B: Base of plate
• C: Camera unit

Wiring Connections

• Red/Black wire: "ENGAGED-PLEASE WAIT" connector.
• Green wires: Entrance panel push-button.
• Black/White wires: Entrance panel LED.

Terminal Descriptions

• S: Lock (open collector)
• TEL: Not used
• B1: 2-Wire Bus
• B2: 2-Wire Bus
• M: Ground / Video Ground
• PA: Open door input (connect to M).
• CA: Door lock release (connect to M).
• M: Ground
• 12V: Output +12V max 100mA.

Operation

Assigning Call Push-Button

Procedure: Press reset, hold call, release reset. Wait 2s for tone. Release call button within 2s. Within 25s, press an actuator button on an interphone/video interphone to associate it. A tone confirms assignment. Timeout tone if failed.

Caution: Using lock release button may open the connected lock.

Call Functionality

Ringtone is regenerated (1s sound/2s pause). Monitor activates immediately. Answer by lifting handset or pressing hook. Conversation duration is panel-set. Subsequent calls within 10s allow direct answer.

Ringtone Muting

Indicated by short "Beeps" if call to muted unit.

Engaged Status

"ENGAGED-PLEASE WAIT" indicator shows busy line. Art. 692S separator prevents line blockage.

Bus Termination and Identification

Bus Termination

4-position connector (Fig. 5). Jumper settings (A-B, B-C, C-D) for bus termination (100 ohm or 50 ohm). Optimal setting required for best vision.

• A: No Termination
• B: 100 ohm Termination (Elvox cable)
• C: 50 ohm Termination (CAT5 cable)

Assigning Identification (ID)

4 DIP switches (Fig. 6) assign panel ID. Each panel needs a unique ID. Table 1 shows DIP switch settings for IDs 0-15. Type 692U cannot be MASTER. Position 1 is for factory testing.

Wiring Diagrams

Diagrams illustrate system configurations with main panels, outdoor units (camera/audio), internal units, power supplies, and distributors. Key connections include bus lines, power, lock release, call buttons, status indicators, and name-tag lighting. Distributors (passive Art. 692D, active Art. 692D/2) manage bus devices.

Regulations and Compliance

Installation Rules

Installation by qualified personnel, adhering to local electrical regulations.

Conformity

• EMC Directive: EN 61000-6-1, EN 61000-6-3.
• REACH: Regulation (EU) No. 1907/2006 - Art.33. Product may contain lead traces.

WEEE Information

Symbol of crossed-out bin means separate collection at end-of-life. Return to designated centers or retailers. Retailers with >400m² sales area accept items <25cm free. Proper disposal aids recycling and environmental protection.