Villa Door Station Quick Guide

1. Packing List

Contact your local dealer if the package is damaged or incomplete. The package contents may vary with device model.

2. Appearance

The dimensions, structure, and tail cables may vary with device model. The figures are only for illustrative purpose.

Product Overview

The door station features the following components:

• 1. Microphone
• 2. Network interface
• 3. Lens
• 4. Micro SD card (reserved)
• 5. Card reading area
• 6. Cable interface
• 7. Speaker
• 8. Button
• 9. Indicator: Steady white indicates starting up. Off indicates normal operation or power not connected.

Dimensions: Height: 194mm [7.6"], Width: 102mm [4.0"], Depth: 31mm [1.2"]]

Cable Specifications

The cable specifications are as follows:

3. Installation

3.1 Installation Preparation

Before installation, plan wiring for all cables based on the actual networking conditions. Please prepare the following tools:

• Electric drill
• Phillips screwdriver
• Marker
• Tape measure
• ESD wrist strap/gloves
• Glue gun

3.2 Installation Steps

The following figures are for reference only. The installation method may vary with scenarios.

3.2.1 Wall Mount

NOTE!

The wall mount bracket should be purchased separately. Please consult your technical support for the recommended model.

Step 1: Prepare Mounting Location

• Paste the drill template on the wall with the arrow upward and perpendicular to the floor.
• Use a Ø6mm to Ø6.5mm drill bit to drill two 30 mm-depth holes on the marked positions. Be careful not to damage cables in the wall.
• Insert the expansion bolts into the two holes.

Textual description of diagram: The diagram shows a drill template being placed on a wall, indicating an "UP" direction. Two circular holes are marked for drilling, and a drill with a Ø6.5mm bit is depicted. The square hole is identified as a leading-out hole, and other holes are fixing holes.

Step 2: Attach Bracket

• Fasten the expansion bolts to the bracket with two M3.5 x 25mm countersunk self-tapping screws.

Textual description of diagram: The diagram shows a mounting bracket being attached to a wall using screws.

Step 3: Connect Cables

• Connect the network cable and other cables to the cable interfaces correctly, and then lead the cables out from the cable groove.
• Fix the tail cable cover (with rubber cushion facing inward) onto the door station with two M2.5 x 5mm countersunk screws.

Textual description of diagram: The diagram shows the rear of the door station, highlighting the Network interface, Cover screw hole, Cable interface, and Cable groove. The tail cable cover is shown being attached.

Step 4: Mount Door Station

• Align the slots on the door station with the four holes of the bracket, and then secure them with four M3 x 8mm countersunk screws.

Textual description of diagram: The diagram illustrates the door station being mounted onto the wall bracket using screws, showing alignment of slots and holes.

3.2.2 Recess Mount

NOTE!

The recess bracket and sunshield should be purchased separately. Please consult your technical support for the recommended model.

Step 1: Fix Recess Bracket

• Ensure that the wall has enough space to mount the bracket. The bracket size is 179mm in height, 87mm in width, and 43mm in depth.
• Paste the drill template (shipped with the bracket) on the wall with the arrow upward.
• Use a Ø6mm to Ø6.5mm drill bit to drill two 30 mm-depth holes on the A position. Be careful not to damage cables in the wall.
• Insert expansion bolts into the two holes.
• Drill round holes on the bracket to lead cables according to the wiring in the wall.
• Lead two M3.5 x 25mm countersunk self-tapping screws through the bracket holes to fix the bracket on the wall.

Textual description of diagram: Two diagrams show the recess bracket templates with dimensions and an "UP" arrow. Another diagram illustrates drilling two holes labeled "A" on the wall for bracket fixing.

Step 2: Insert Sunshield

• Insert the sunshield from the rear side of the door station.

Textual description of diagram: The diagram shows the sunshield being inserted into the rear of the door station.

Step 3: Connect Cables

• Connect all cables. See step 3 in Wall Mount.

Step 4: Mount Door Station

• Align the slots on the door station with the four holes of the bracket, and then secure them with four M3 x 8mm countersunk screws.

Textual description of diagram: The diagram illustrates the door station being mounted onto the wall bracket using screws, showing alignment of slots and holes.

4. Startup

After the door station is installed correctly, you can use a network cable to connect the station to the PoE power supply, or connect one end of the power adapter (user-purchased or prepared) to the power interface of the door station and the other end to the mains supply.

5. Web Login

Default Credentials

Default IP address: 192.168.1.13

Default username/password: admin/123456

Note:

For security, please set a strong password of at least nine characters including uppercase and lowercase letters, digits, and special characters. It is strongly recommended to regularly change the device password and keep it secure to ensure that only authorized users can log in.

Disclaimer and Safety Warnings

Copyright Statement

©2024 Zhejiang Uniview Technologies Co., Ltd. All rights reserved. No part of this manual may be copied, reproduced, translated or distributed in any form or by any means without prior consent in writing from Zhejiang Uniview Technologies Co., Ltd.

Trademark Acknowledgements

Uniview and its associated logos are trademarks or registered trademarks of Uniview. All other trademarks, products, services, and companies mentioned are the property of their respective owners.

Export Compliance Statement

Uniview complies with applicable export control laws and regulations worldwide, including those of the People's Republic of China and the United States. Users must strictly abide by applicable export laws and regulations.

EU Authorised Representative

UNV Technology EUROPE B.V. Room 2945, 3rd Floor, Randstad 21-05 G, 1314 BD, Almere, Netherlands.

Privacy Protection Reminder

Uniview is committed to protecting user privacy. Read the full privacy policy on the Uniview website. Use of the product may involve collection of personal information such as face, fingerprint, license plate number, email, phone number, and GPS. Abide by local laws and regulations.

About This Manual

• This manual is intended for multiple product models and software versions; actual appearances and functions may differ.
• Technical or typographical errors may exist. Uniview is not responsible for such errors and reserves the right to change the manual without prior notice.
• Users are responsible for damages arising from improper operation.
• Uniview reserves the right to change information without prior notice. The manual will be periodically updated.

Disclaimer of Liability

The product is provided "as is". This manual is for informational purposes only. Uniview provides no warranty, expressed or implied, including warranties of merchantability, fitness for a particular purpose, and non-infringement.

Uniview's total liability for damages related to this manual will not exceed the amount paid for the product, except as required by law for personal injury.

Users assume all risks associated with connecting the product to the Internet, including network attacks, hacking, and viruses. Uniview recommends implementing security measures for network, device, data, and personal information.

Uniview and its affiliates are not liable for losses arising from the use or inability to use the product or service, including lost profits, data loss, property damage, personal injury, business interruption, or other damages, regardless of the theory of liability.

Network Security

Enhance network security for your device:

• Change default password: Set a strong password of at least nine characters with digits, letters, and special characters.
• Keep firmware up to date: Visit Uniview's official website or contact your dealer for the latest firmware.
• Change password regularly: Keep your password safe.
• Enable HTTPS/SSL: Encrypt HTTP communications.
• Enable IP address filtering: Allow access only from specified IP addresses.
• Minimum port mapping: Configure router/firewall for minimal ports. Do not set the device as DMZ host or use full cone NAT.
• Disable automatic login/save password: Prevent unauthorized access on shared computers.
• Choose username/password discretely: Avoid using credentials from social media, bank, or email accounts.
• Restrict user permissions: Grant only necessary permissions.
• Disable UPnP: Prevents automatic port mapping and potential data leakage.
• Multicast: Disable if not used for transmitting video to multiple devices.
• Check logs: Regularly check for unauthorized access or abnormal operations.
• Isolate video surveillance network: Prevent unauthorized access from other service networks.
• Physical protection: Keep the device in a locked room or cabinet.
• SNMP: Disable SNMP if not used; use SNMPv3 if necessary.

Learn More: Obtain security information from Uniview's official website.

Safety Warnings

The device must be installed, serviced, and maintained by trained professionals. Read this guide carefully before use to avoid danger and property loss.

Storage, Transportation, and Use

• Store and use the device in a proper environment (temperature, humidity, dust, corrosive gases, electromagnetic radiation).
• Ensure secure installation on a flat surface to prevent falling. Do not stack devices unless specified.
• Ensure good ventilation; do not cover vents. Allow adequate space.
• Protect from liquids.
• Use a stable power supply meeting device requirements. Ensure power supply output exceeds total power of connected devices.
• Verify proper installation before connecting to power.
• Do not remove device seals or attempt self-service. Contact a professional for maintenance.
• Always disconnect power before moving the device.
• Take waterproof measures for outdoor use.

Power Requirements

• Install and use according to local electrical safety regulations.
• Use a UL certified power supply meeting LPS requirements if using an adapter.
• Use the recommended cordset (power cord) with specified ratings.
• Only use the power adapter supplied with the device.
• Use a mains socket outlet with protective earthing (grounding).
• Ground the device properly if intended.

Battery Use Caution

• Avoid extremely high/low temperatures and air pressure during use, storage, and transportation.
• Do not replace the battery yourself.
• Improper battery use can cause fire, explosion, or leakage of flammable liquid or gas. This includes replacing with the incorrect type, disposing in fire/hot oven, or mechanical crushing/cutting.
• Dispose of used batteries according to local regulations or manufacturer instructions.

Personal Safety Warnings

Chemical Burn Hazard: This product contains a coin cell battery. Do NOT ingest. Ingestion can cause severe internal burns and death.

Keep new and used batteries away from children.

If the battery compartment does not close securely, stop using the product and keep it away from children.

If batteries are swallowed or placed inside the body, seek immediate medical attention.

Avertissement de l'utilisation de la batterie

French Warning: Évitez les températures et pressions d'air extrêmes pendant l'utilisation, le stockage et le transport. Ne remplacez pas la batterie vous-même. Une mauvaise utilisation de la batterie peut entraîner des risques d'incendie, d'explosion ou de fuite de gaz inflammables. Jetez les batteries usagées conformément aux réglementations locales ou aux instructions du fabricant.

Avertissements de sécurité personnelle

French Warning: Risque de brûlure chimique. Ce produit contient une pile bouton. Ne pas ingérer. Si la pile est avalée, elle peut causer de graves brûlures internes en seulement 2 heures et peut entraîner la mort. Gardez les batteries neuves ou utilisées à l'écart des enfants. Si le compartiment de la batterie ne se ferme pas en toute sécurité, cessez d'utiliser le produit et gardez-le à l'écart des enfants. Si vous pensez que des piles ont pu être avalées ou placées à l'intérieur d'une partie du corps, consultez immédiatement un médecin.

Regulatory Compliance

FCC Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Visit http://en.uniview.com/Support/Download_Center/Product_Installation/Declaration/ for SDoC. Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

LVD/EMC Directive

This product complies with the European Low Voltage Directive 2014/35/EU and EMC Directive 2014/30/EU.

WEEE Directive-2012/19/EU

The product this manual refers to is covered by the Waste Electrical & Electronic Equipment (WEEE) Directive and must be disposed of in a responsible manner.

Battery Regulation- (EU) 2023/1542

Battery in the product complies with the European Battery Regulation (EU) 2023/1542. For proper recycling, return the battery to your supplier or to a designated collection point.