RF Exposure Evaluation Report

Cover Page

Application No.: KSCR2411002241AT

FCC ID: 2AL8S-0235C9TF

Applicant: Zhejiang Uniview Technologies Co., Ltd.

Address of Applicant: No. 369, Xietong Road, Xixing Sub-district, Binjiang District, Hangzhou City, 310051, Zhejiang Province, China

Manufacturer: Zhejiang Uniview Technologies Co., Ltd.

Address of Manufacturer: No. 369, Xietong Road, Xixing Sub-district, Binjiang District, Hangzhou City, 310051, Zhejiang Province, China

Factory: Zhejiang Uniview System Technology Co., Ltd.

Address of Factory: No.1277 Qingfeng South Road (South), Tongxiang Economic Development Zone, Tongxiang City, Jiaxing City, 314500, Zhejiang, China

Equipment Under Test (EUT): IP Camera

EUT Name: IPC2A14LP-ADF40KC-4G-US,IPC2A14LP-ADF60KC-4G-US,IPC2A14LP-xxxxxxxx-yyyyyyyy-zzzz-mmmm (where "x","y","z","m" may be 0-9 A-Z a-z or blank, or -. "-" is optional. The differences no impact safety related constructionsand EMC)

Model No.:

Standard(s): FCC Rules 47 CFR §2.1091, KDB 447498 D04 interim General RF Exposure Guidance v01

Date of Receipt: 2024-11-07

Date of Test: 2024-12-16 to 2024-12-24

Date of Issue: 2024-12-26

Test Result: Pass*

* In the configuration tested, the EUT complied with the standards specified above.

This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein.

Any holder of this document is advised that information contained hereon reflects the Company's findings at the time of its intervention only and within the limits of Client's instructions, if any. The Company's sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law.

Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

Compliance Certification Services (Kunshan) Inc.

No.10 Weiye Road, Development Zone, Kunshan, Jiangsu, China

Tel: +86 512 5735 5888 Fax: +86 512 5737 0818

www.sgsgroup.com.cn sgs.china@sgs.com

Member of the SGS Group (SGS SA)

Revision Record

Authorized for issue by:

Tested By: Maker Qi /Project Engineer

Approved By: Terry Hou /Reviewer

Contents

1. Cover Page
2. Contents
3. General Information
   • 3.1 General Description of E.U.T.
   • 3.2 Details of E.U.T.
   • 3.3 Test Location
   • 3.4 Test Facility
4. FCC Radiofrequency radiation exposure limits
5. Measurement and Calculation
   • 5.1 Maximum transmit power
   • 5.2 MPE Calculation

General Information

3.1 General Description of E.U.T.

Power supply: DC 12V/1A

3.2 Details of E.U.T.

4G

Operation Frequency: LTE Band 2,4,5,12,13,14,66,71

Modulation Type: QPSK/16QAM

Antenna Type: Dipole Antenna

Antenna Gain: Band 2: 5.2dBi (Provided by the manufacturer), Band 4: 4.4dBi (Provided by the manufacturer), Band 5: 0.8dBi (Provided by the manufacturer), Band 12: 1.2dBi (Provided by the manufacturer), Band 13: 0.8dBi (Provided by the manufacturer), Band 14: 0.8dBi (Provided by the manufacturer), Band 66: 4.4dBi (Provided by the manufacturer), Band 71: 1.2dBi (Provided by the manufacturer)

Test Location

All tests were performed at: Compliance Certification Services (Kunshan) Inc. No.10 Weiye Rd, Innovation park, Eco&Tec, Development Zone, Kunshan City, Jiangsu, China. Tel: +86 512 5735 5888 Fax: +86 512 5737 0818

No tests were sub-contracted.

Note:

1. SGS is not responsible for wrong test results due to incorrect information (e.g. max. clock frequency, highest internal frequency, antenna gain, cable loss, etc.) is provided by the applicant. (if applicable).
2. SGS is not responsible for the authenticity, integrity and the validity of the conclusion based on results of the data provided by applicant. (if applicable).
3. Sample source: sent by customer.

3.4 Test Facility

The test facility is recognized, certified, or accredited by the following organizations:

• A2LA Compliance Certification Services (Kunshan) Inc. is accredited by the American Association for Laboratory Accreditation (A2LA). Certificate No. 2541.01.
• FCC Compliance Certification Services (Kunshan) Inc. has been recognized as an accredited testing laboratory. Designation Number: CN1172.
• ISED Compliance Certification Services (Kunshan) Inc. has been recognized by Innovation, Science and Economic Development Canada (ISED) as an accredited testing laboratory. Company Number: 2324E
• VCCI The 3m and 10m Semi-anechoic chamber and Shielded Room of Compliance Certification Services (Kunshan) Inc. has been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: R-20134, R-11600, C-11707, T-11499, G-10216 respectively.

FCC Radiofrequency radiation exposure limits

According to §1.1310, The criteria listed in the following table shall be used to evaluate the environment impact of human exposure to radio frequency (RF) radiation as specified in part1.1307(b)

Measurement and Calculation

5.1 Maximum transmit power

The Power Data is based on the RF Test Report R2203A0238-R1, R2203A0238-R2, R2203A0238-R3, R2203A0238-R4.

5.2 MPE Calculation

According to the formula S=P/4πR², we can calculate S which is MPE.

Note:

1. P (mW)
2. R = distance to the center of radiation of antenna (in centimeter)

For FCC