MIPRO BC-100 II

Part Names

Diagram showing the top view of the MIPRO BC-100 II base unit, with numbered callouts for the boundary microphone, TALK/MUTE button, charging socket, and microphone selection switch.

• 1: 4-Pin XLR Input Connector for Gooseneck Microphones
• 2: Boundary Microphone
• 3: TALK Status Indicator Light
• 4: TALK/MUTE Push Button
• 5: Charging Socket and Charging Indicator
• 6: Microphone Selection Switch

Diagram showing the rear view of the MIPRO BC-100 II base unit, with numbered callouts for the 4-pin XLR input, balanced 3-pin XLR output, and XLR connector for bodypack transmitter.

• 7: Balanced 3-Pin XLR Output Connector
• 8: XLR Connector for Bodypack Transmitter
• 9: Bodypack Transmitter Slot and Fasten Holder

Diagram showing a side view with internal components and numbered callouts for the bodypack transmitter slot, charging contact pins, and base cover latch.

• 10: Charging Contact Pins
• 11: Base Cover Latch

Diagram showing the bottom view of the MIPRO BC-100 II base unit, with numbered callout for the base cover.

• 12: Base Cover

Installing and Operating the Transmitter

1. Remove the belt clip from the back of the MIPRO bodypack transmitter.
   Illustration of a MIPRO bodypack transmitter with its belt clip being removed.
2. Rotate the base cover latch 180 degrees and push gently in the direction of the "OPEN" arrow to remove the base cover.
   Sequence of illustrations showing how to remove the base cover: rotating the base cover latch 180 degrees and pushing gently in the direction of the "OPEN" arrow.
3. Align the XLR connector 8 with the input socket of the transmitter and connect them securely.
   Illustration showing the alignment of the XLR connector on the transmitter with the input socket on the base unit, highlighting the groove and latch mechanism.
4. Insert the transmitter into the bodypack transmitter slot 9 and rotate the fasten holder to fix it in place.
5. If the transmitter supports charging, ensure the charging contacts 10 align with the contact pins to enable proper charging.
   Illustrations showing the transmitter being inserted into the slot and the alignment of charging contacts with the contact pins on the base unit.
6. Power on the transmitter, replace the base cover, and rotate the base cover latch 11 to secure it.
   Illustrations showing the transmitter powered on and the base cover being secured by pushing upward and rotating the latch.
7. For detailed transmitter settings, refer to the transmitter's user guide.

Charging Instructions

1. Connecting the Charging Equipment
   Plug the charger into a power outlet and connect the charging cable to the charging socket 5 on the device.
   Note: Ensure the device is powered off during charging.
2. Confirming Charging Status
   • Red Indicator Light: Charging in progress.
   • Green Indicator Light: Fully charged.
3. Troubleshooting Charging Issues
   • If the charging indicator does not light up, check whether the charging cable and plug are securely connected.
   • Note: Always use the MIPRO-supplied charger to avoid damage or overcharging of the battery.
4. Long-Term Storage
   If the device will not be used for an extended period, remove the battery to prevent power drain and store it properly.
   Diagram illustrating the charging setup: a power outlet, a charger adapter, a charging cable connecting to the MIPRO BC-100 II base unit's charging socket. Text indicates "(DC 5V)" and plug dimensions. A charging indicator light is also shown.

Boundary Microphone Mode

1. Wired Operation
   • Confirm that the microphone selection switch 6 is set to the "Boundary in" position.
     Illustration showing the microphone selection switch position.
   • Use the 3-pin XLR output connector 7 to connect the signal cable to a mixer or other audio equipment with phantom power.
     Illustration showing the 3-pin XLR output connector connected to a PA system.
   • Ensure the device is properly powered on. The boundary microphone 2 on the base unit can then be used for speech.
   • During speech, use the TALK/MUTE push button 4 to control the status. Switch to TALK for speech or MUTE for silence. The indicator light will turn on or off according to the selected mode.
     Illustrations of the TALK/MUTE button and indicator light: "TALK" mode with indicator light on, and "MUTE" mode with indicator light off.
2. Wireless Operation
   • Confirm that the microphone selection switch 6 is set to the "Boundary in" position.
     Illustration showing the microphone selection switch position.
   • Install the bodypack transmitter onto the base unit. For detailed steps, refer to Page 2: Installing and Operating the Transmitter.
   • Ensure the transmitter and receiver are properly paired. Once paired, the boundary microphone 2 on the base unit can be used for wireless speech.
   • During speech, use the TALK/MUTE toggle switch 4 to control the status. Switch to TALK for speech or MUTE for silence. The indicator light will turn on or off according to the selected mode.
     Illustrations of the TALK/MUTE button and indicator light: "TALK" mode with indicator light on, and "MUTE" mode with indicator light off.

Gooseneck Microphone Mode

1. Wired Operation
   • Insert the gooseneck microphone into the 4-Pin XLR input connector 1 on the base unit, ensuring it is securely fixed. Rotate the locking ring counterclockwise to secure the microphone. If removal is needed, rotate the locking ring clockwise.
     Illustration showing a gooseneck microphone being inserted into the 4-Pin XLR input connector on the base unit, with a close-up of the XLR connector alignment and locking ring mechanism.
   • Confirm that the microphone selection switch 6 is set to the "Mic in" position.
     Illustration showing the microphone selection switch position.
   • Use the 3-pin XLR output connector 7 to connect the signal cable to a mixer or other audio equipment with phantom power.
     Illustration showing the 3-pin XLR output connector connected to a mixer or PA system.
   • Before powering on, ensure the input connector is securely connected to the microphone signal source to avoid noise during startup.
   • Confirm that the device is properly powered on, and the gooseneck microphone can then be used for speech.
   • During speech, use the TALK/MUTE push button 4 to control the status. Switch to TALK for speech or MUTE for silence. The indicator light will turn on or off according to the selected mode.
     Illustration showing a gooseneck microphone attached to the base unit, the device powered on, and the TALK/MUTE button operation with indicator lights for TALK (on) and MUTE (off).
2. Wireless Operation
   • Install the bodypack transmitter onto the base unit. For detailed steps, refer to Page 2: Installing and Operating the Transmitter.
   • Insert the gooseneck microphone into the 4-Pin XLR input connector 1 on the base unit, ensuring it is securely fixed. Rotate the locking ring counterclockwise to secure the microphone. To remove, rotate the locking ring clockwise.
     Illustration showing a gooseneck microphone being inserted into the 4-Pin XLR input connector on the base unit, with a close-up of the XLR connector alignment and locking ring mechanism.
   • Confirm that the microphone selection switch 6 is set to the "Mic in" position.
     Illustration showing the microphone selection switch position.
   • Pairing Operation: Pair the internal transmitter with a receiver from the same series and frequency band. The pairing method (ACT synchronization) is the same as that of handheld and bodypack transmitters. Once pairing is complete, the device is ready for use.
     Illustration showing a gooseneck microphone attached to a bodypack transmitter, and the transmitter being paired with the base unit. The text mentions "ACT synchronization".
   • During speech, use the TALK/MUTE push button 4 to control the status. Switch to TALK for speech or MUTE for silence. The indicator light will turn on or off according to the selected mode.
     Illustrations of the TALK/MUTE button and indicator light: "TALK" mode with indicator light on, and "MUTE" mode with indicator light off.

Notes

1. In the event of any discrepancy, refer to the actual product as the final standard.
2. The carrier frequency range, output power, and maximum deviation are subject to the radio regulations of the respective countries.
3. For condenser microphones, it is strictly prohibited to spray alcohol directly onto the device for cleaning, as this may cause severe damage and invalidate the warranty.

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices).

FCC Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 2 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Industry Canada Statement

This device complies with Industry Canada RSS-247 standard. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

IC Radiation Exposure Statement:

This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 2 cm between the radiator and your body.

Cet équipement est conforme aux CNR-102 d'Industrie Canada. Cet équipement doit êtreinstallé et utilisé avec une distance minimale de 2 centimètres entre le radiateur et votrecorps. Cet émetteur ne doit pas être co-localisées ou opérant en conjonction avec autreantenne ou émetteur. Les antennes utilisées pour cet émetteur doivent être installés etfournir une distance de séparation d'au moins 2 centimètre de toute personne et doit pas être co-située ni fonctionner en conjunction avec une autre antenne ou émetteur.

Disposal Information

Dispose of any unusable devices or batteries responsibly and in accordance with any applicable regulations.

Disposing of used batteries with domestic waste is to be avoided! Batteries / NiCad cells often contain heavy metals such as cadmium(Cd), mercury(Hg) and lead(Pb) that makes them unsuitable for disposal with domestic waste. You may return spent batteries/accumulators free of charge to recycling centres or anywhere else batteries/accumulators are sold.

By doing so, you contribute to the conservation of our environment! [♻️]