MIPRO ST-32/SM-32 Saxophone & Wind Instrument Microphone Set User Guide

Introduction

This user guide provides detailed information for the MIPRO ST-32 and SM-32 Saxophone & Wind Instrument Microphone Sets. It covers parts identification, assembly procedures for both wireless and wired configurations, important usage notes, disposal guidelines, and technical compliance information.

Parts Identification

ST-32 Gooseneck Microphone Transmitter Set Components:

• ST-32 Gooseneck Microphone Transmitter
• MU-10 Interchangeable Capsule (1)
• MU-16 Interchangeable Capsule (2)
• MU-20 Interchangeable Capsule (3)
• SH-10S Saxophone Microphone Clip (4)
• Gooseneck: Bendable and adjustable for ideal angle and position
• Clip Slot for SH-10S (4)

SM-32 Saxophone & Wind Instrument Microphone Set Components:

• SM-32 Microphone Set
• MU-10 Interchangeable Capsule (1)
• MU-16 Interchangeable Capsule (2)
• MU-20 Interchangeable Capsule (3)
• SH-10S Saxophone Microphone Clip (4)
• SC-32 Saxophone Microphone Output Connector (TA4F or XLR) (6)

Assembly and Usage

ST-32 Gooseneck Microphone Transmitter Assembly:

1. Attach the SH-10S microphone clip to the T-32 gooseneck transmitter.
2. Mount the T-32 gooseneck transmitter onto a saxophone or wind instrument using the SH-10S microphone clip. The gooseneck can be bent and adjusted for optimal positioning.

Diagram Description: An illustration shows the SH-10S clip attached to the T-32 gooseneck, which is then clipped onto a saxophone.

SM-32 Saxophone & Wind Instrument Microphone Set Assembly:

1. Install the SH-10S microphone clip and the SC-32 saxophone microphone cable onto the SM-32M microphone set.
2. Secure the SM-32M microphone set onto a saxophone or wind instrument using the SH-10S microphone clip.
3. For Wireless Transmission: Connect the SC-32 Saxophone Microphone Cable to a MIPRO bodypack transmitter. This enables wireless transmission to a PA system via a receiver.
4. For Wired Transmission: Connect the SC-32 Saxophone Microphone Cable to a MIPRO MJ-53 Condenser Microphone Adaptor. The MJ-53 provides 12V~48V DC phantom power and features an XLR output for connecting to a mixer.

Diagram Description: Illustrations show the SM-32M set attached to a saxophone, connected via the SC-32 cable to a transmitter for wireless transmission to a PA system, and also connected via the SC-32 cable to an MJ-53 adaptor for wired transmission to a PA system.

Important Notes

• Please refer to the actual product for any discrepancies in product descriptions.
• Frequency range and maximum deviation adhere to the regulations of various countries.
• Caution: Avoid spraying alcohol directly onto the condenser capsule module, as this can cause severe damage and void the warranty.
• To attach or detach the SH-10S Saxophone Microphone Clip, gently pull the clip open with your thumb.

Disposal Information

[disposal-icon] Please dispose of unusable devices and batteries responsibly, following all applicable regulations. Do not dispose of used batteries with household waste, as they may contain hazardous heavy metals. Return spent batteries and accumulators to designated recycling centers or retail points for proper disposal and environmental protection.

Technical Compliance

FCC & IC Compliance Statements:

THIS DEVICE COMPLIES WITH PART 74 OF THE FCC RULES AND RSS-123 ISSUE 2 OF CANADA.

OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS:

• (1) This device may not cause harmful interference.
• (2) This device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

French Translation: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Manufacturer Information

MIPRO Electronics Co., Ltd

Headquarters: No. 814, Beigang Rd., Chiayi City 600079, Taiwan

Tel: +886-5-238-0809 Fax: +886-5-238-0803

Website: www.mipro.com.tw

Email: mipro@mipro.com.tw

Product Model: ST-32/SM-32 (Part Number: 2CE534B)

All rights reserved. Reproduction or distribution without prior approval from MIPRO is prohibited. Specifications and design are subject to change without notice.