AWE
AWE AirGate™ Carbon Intake for Audi B9 SQ5 3.0T - AWEContact - AWEWarranty, return, cancellation policies - AWE
Installation Guide for AWE models including: 2660-15060, 2660-15062, 2660-15060 AirGate Carbon Fiber Intake, 2660-15060, AirGate Carbon Fiber Intake, Carbon Fiber Intake, Fiber Intake, Intake
AWE Tuning | 2660-15060 | AWE AirGate™ Carbon Fiber Intake for Audi B9 SQ5 3.0T - With Lid fiber airbox and included S-FLO Filter makes for a more aggressive intake note, with an intoxicating turbo spool sound. FITMENT NOTE:The AWE AirGate™ Carbon Intake for the B9 SQ5 is NOT applicable to Euro-spec models.
AWE AirGate™ Carbon Intake for Audi B9 SQ5 3.0T - AWE
2 days ago — For up-to-date fitment information, please visit the product page on. AWE-Tuning.com. Installation questions? CONTACT US. These instructions are intended for ...
File Info : application/pdf, 9 Pages, 4.36MB
DocumentDocumentThese instructions are intended for the following part numbers: 2660-15060, 2660-15062 Vehicle Fitment: For up-to-date fitment information, please visit the product page on AWE-Tuning.com. Thank you for purchasing the AWE AirGateTM Carbon Intake system. Exquisite build quality with industry leading performance distinguish this intake kit from all others. Copyright 2018, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. Al rights reserved. Rev1.6 Installation questions? CONTACT US Inspect ALL parts prior to disassembly of vehicle; If damaged OR MISSING, please contact the place of purchase immediately. Arrow Quantity Part Description AirGateTM Carbon Intake parts: A 1 AirGateTM carbon air box B 1 Carbon inlet duct C 1 Carbon outlet tube D 1 Performance air filter E 3 M5 x 16mm bolts F 2 Worm clamps G 1 Silicone intake coupler H 1 Mounting bracket AirGateTM Lid: I 1 AirGateTM Lid J 2 M5 x16mm bolts Part Number 500003 500034 500033 GF4171 94500A231 W053917090 300009 110039 500007 94500A231 Copyright 2018, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. Al rights reserved. Rev1.6 Under the hood, remove the hood release lever by depressing the retaining button located by the arrow in Figure 1. Remove the upper radiator cover by lifting up at the arrows in Figure 2-1. Lift and slide forward to remove the cover completely. NOTE: Temporarily reinstall the hood release lever. If the hood should ever close without this in place, opening the hood again will be difficult. Remove the air box inlet duct by removing the two T25 torx screws, shown by the arrows in Figure 3. Slide the inlet duct toward the engine, lift up, and remove completely. Copyright 2018, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. Al rights reserved. Rev1.6 Pop the engine cover off of the four mounting pins by lifting up gently. Loosen the two hose clamps, shown in Figure 5, and remove the OEM inlet hose. Gently lift upwards on the OEM intake box to remove it from the three post mounts. Check for any rubber grommets still in the OEM mount points or still attached to the posts on the box, as shown by the arrow in Figure 6-2 and remove the grommets, for use later. Copyright 2018, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. Al rights reserved. Rev1.6 Remove the nut and bracket, shown in Figure 7, as theses parts are not needed for your AWE intake. In some vehicles the forward upper control arm bolt protrudes into the passenger side engine bay area, as shown in Figure 8-1. This interferes with the intake fitment so this bolt should be swapped with the shorter driver side forward upper control arm bolt. Figure 6.3 shows the swapped control arm bolts. Figure 8-2, shows the length difference in the driver and passenger bolt. DS PS Copyright 2018, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. Al rights reserved. Rev1.6 Gather the supplied AWE mounting bracket, remove the two nuts pointed out in Figure 9-1. Install the mounting bracket with the arrow on the bottom side, facing the front of the vehicle, as shown in Figure 9-2. Gather the OEM rubber mounts removed in Step 6 and install them onto the mounting tabs on the AWE intake box, shown in Figure 10. Pre-assemble the AirGateTM carbon air box by installing the S-FLO filter, making sure the end with the smaller hole positioned onto the post inside the box, as shown by Arrow A in Figure 11. Install the carbon turbo tube at the open end of the S-FLO filter and clock until all three (3) mount holes align, shown by Arrow B in Figure 11. Use the included M5 washers and screws to secure the carbon turbo tube into position. NOTE: If using the AirGateTM Lid, install into position and secure with the remaining M5 washers and screws, as shown by Arrow C in Figure 11. Copyright 2018, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. Al rights reserved. Rev1.6 Install the included silicone coupler onto the carbon turbo tube using two of the included worm clamps, as shown in Figure12. Place the assembly into the engine bay and align the three OEM rubber grommets, referenced in Step 10. Gently push downward on the corners of the intake box to affix the assembly into location. Gently tug upward to make sure the box is securely in place With the AWE intake box install tighten the hose two clamps. Carefully align the carbon inlet with the intake box and the mounting locations shown by the arrows in Figure 13. Reinstall the plastic screws that were removed in Step 3 with the T25 torx driver, as shown by the arrows in Figure 13. Reinstall the engine cover removed in Step 4, as shown in Figure 14. Copyright 2018, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. Al rights reserved. Rev1.6 If the hood release lever is still installed, as recommended in Step 1, remove it in order to reinstall the upper radiator cover, as shown by Arrow A in Figure 15. Reinstall the hood release, shown by Arrow B in Figure 15. About the AirGateTM Lid: Removing this panel will increase the presence of sounds that resonate from the turbo under boost. Installing this panel shields the intake and filter from the higher air temperatures that are present in the engine bay while reducing the sounds that come from the intake. Copyright 2018, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. Al rights reserved. Rev1.6 This is a re-usable air filter that can be cleaned when dirty and put back into service. Please inspect the air filter element every 25,000 miles for integrity. Clean every 50,000 miles under normal operating conditions, sooner in dusty conditions. Contact AWE to purchase a filter maintenance kit. Under heat, carbon fiber may mature to present a gold hue - this is a normal reaction to spirited driving. Any questions or comments, please do not hesitate to contact us: AWE 215-658-1670 CONTACT FORM Up-to-date warranty information is found HERE. Copyright 2018, AWE. No part of this document may be reused or duplicated without the express permission of AWE/Secor Ltd. Al rights reserved. Rev1.6