VIVO Water Cooler Truck Mount

Safety Information

⚠️ CAUTION!

If you do not understand these directions, or if you have any doubts about the safety of the installation, please contact VIVO product support at 309-278-5303 or help@vivo-us.com for further assistance. Check carefully to make sure there are no missing or defective parts. Improper installation may cause damage or serious injury. Do not use this product for any purpose that is not explicitly specified in this manual. Do not exceed weight capacity. VIVO cannot be liable for damage or injury caused by improper mounting, incorrect assembly or inappropriate use.

⚠️ WARNING: CHOKING HAZARD

SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.

DO NOT EXCEED WEIGHT CAPACITY

[weight-symbol] FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY.

Support and Contact Information

Open Monday - Friday 7:00am - 7:00pm CST. VIVO's dedicated support team can offer immediate assistance with rapid response times. If any parts are received damaged or defective, please contact VIVO. We are happy to replace parts to ensure you have a fully functioning product.

Contact Us:

• ? Give us a Call: 309-278-5303 (AVG. RESOLUTION TIME (within office hrs): 5M 4S)
• ? Chat Us: www.vivo-us.com (AVG. RESOLUTION TIME (within office hrs): < 15 M)
• ? Email Us: help@vivo-us.com (AVG. RESPONSE TIME (within office hrs): 1HR 8M - 23% within < 15m, 38% within < 30m, 61% within < 1hr, 83% within < 2hr, 92% within < 3hr)

Package Contents

• A (x1): Main Bracket
• B (x2): Strap
• C (x1): Upper Bracket
• D (x1): Lower Bracket

Included Hardware

• S-A (x10): M6x10mm Flathead Screw
• S-B (x3): M10 Washer
• S-C (x3): M10 Nut
• S-D (x3): M10x30mm Screw
• S-E (x3): ST10x30mm Screw

Tools Needed

• Adjustable Wrench
• 4mm Allen Wrench

Weight Capacity

44lbs (20kg)

Assembly Steps

STEP 1

Connect the Lower Bracket (D) to the Main Bracket (A) using the M6x10mm Flathead Screws (S-A). Tighten screws using a 4mm Allen Wrench.

Diagram Description: Shows the Lower Bracket (D) being attached to the lower section of the Main Bracket (A) using four M6x10mm Flathead Screws (S-A). The screws are depicted being tightened with a 4mm Allen Wrench.

STEP 2

Connect the Upper Bracket (C) to the Main Bracket (A) using the M6x10mm Flathead Screws (S-A). Tighten screws using a 4mm Allen Wrench.

Diagram Description: Shows the Upper Bracket (C) being attached to the middle section of the Main Bracket (A) using four M6x10mm Flathead Screws (S-A). The screws are depicted being tightened with a 4mm Allen Wrench.

STEP 3

Metal Rail/Plate Installation:

Hold the bracket assembly up to your desired mounting location and mark hole using a marker. Drill through holes using a 7/16" (11mm) drill bit. Attach the assembly using M10x30mm Screws (S-D), M10 Washers (S-B), and M10 Nuts (S-C). Tighten using a 17mm wrench.

Diagram Description: Illustrates the bracket assembly being positioned for mounting. For metal rail/plate installation, it shows M10x30mm Screws (S-D) passing through the bracket holes, M10 Washers (S-B), and secured with M10 Nuts (S-C). A 17mm wrench is implied for tightening.

Wood Board Installation:

Hold the bracket assembly up to your desired mounting location and mark holes using a marker. Drill 1” (25mm) deep holes using a 9/32" (7mm) bit. Attach the assembly using ST10x30mm Screws (S-E) and M10 Washers (S-B). Tighten using a 17mm wrench.

Diagram Description: For wood board installation, it shows ST10x30mm Screws (S-E) being used with M10 Washers (S-B) to attach the assembly to a wooden surface after drilling pilot holes. A 17mm wrench is implied for tightening.

STEP 4

Thread the Straps (B) through the Main Bracket (A) and secure up to 5 gallon water jugs.

Diagram Description: Shows the two Straps (B) being threaded through slots on the Main Bracket (A). The straps are depicted securing a large water jug (up to 5 gallons) in place.