eSUN eBOX Lite User Guide
Please read the user guide before use and keep it carefully.
Attention
Please read this manual thoroughly before operating the machine and save it for some unexpected situation.
- Pull out the attaching plug if the power line or socket is worn or damaged.
- Cut the power off when not in use.
- DO NOT let children operate it without supervision.
- DO NOT touch the bottom plate when drying filaments to avoid burns.
- Turn off the machine when not in use.
- DO NOT use it in a damp environment.
- Cut off the power and contact eSUN immediately if something is wrong.
- DO NOT disassemble or repair it without guidance.
Instruction
This user guide is provided for the convenience of users. Pictures and descriptions may slightly vary from the actual product. The contents of this user guide can be changed without notice.
- eSUN is not liable for any direct or indirect damage due to user negligence.
- eSUN will not take responsibility for damage caused by misoperation.
- Please read this manual thoroughly before use.
- Please make sure the socket voltage matches the product before use.
- Please remove all packaging items from the product before using it for the first time.
- Put the product on a horizontal table.
Product Name of Each Part
The eBOX Lite consists of the following parts:
- Spool
- Bottom case
- Display screen
- Button
- Upper cover
- Power interface
- Bottom cover
- Foot pad
[Diagram showing the different parts of the eBOX Lite with labels]
Product Specification Table
| Specification | Details |
|---|---|
| Package Size | 249(L)×138(W)×272.5(H) mm |
| Product Size | 215(L)×104(W)×238.5(H) mm |
| Max Capacity | Φ200×73(H) mm |
| Product Weight | 750g |
| Rated Power | AC100-240V~50/60Hz |
| Power Output | DC24V~2A |
| Power of Heater | 35W |
| Filament Diameter | 1.75mm/2.85mm/3mm |
Certification System
The product is certified with CE, FC, ROHS, and REACH standards. [CE logo] [FC logo] [ROHS logo] [REACH logo]
Method of Use
- Plug the adapter into the AC100-240V ~ 50 / 60Hz power supply and plug the output terminal into the interface at the tail of the eBOX. [Illustration of plugging in the adapter]
- Press the power button ▶️ to start. [Illustration of the eBOX with display showing '0003']
- Open the upper cover, place the desiccant into the empty slot in the rear of the box, then place the spool inside. [Illustration showing desiccant placement and spool insertion]
- Place the spool in and pull the filament out through the outlet. Close the cover. The direction to pull filament can be bottom-up, or from top to bottom, depending on the position of the printer. [Illustration showing filament being pulled through the outlet]
Parameter Setting
The product has four buttons: the open button [power symbol], the function button [function symbol], the up button [up arrow symbol], and the down button [down arrow symbol].
The product has two modes: Temperature Setting Mode (TEMP) and Heating Time Setting Mode (TIME).
Press the function button [function symbol] to switch modes, and the up/down buttons [up/down arrow symbols] to change the parameters.
The system enters dormancy after 5 seconds of no operation; the backlight disappears in dormant state. Press any button to wake up, then press the function button [function symbol] to set parameters or shut down.
Temperature Setting Mode
Press the function button [function symbol] three times to switch to the Temperature Setting Mode. The screen will display 'TEMP'. There are 3 levels in total, adjustable by the up [up arrow symbol] or down [down arrow symbol] buttons. A higher number indicates a higher temperature. '0' means no heating.
[Image of the display showing 'TEMP' and '0003']
A higher level results in a higher temperature inside the box and lower humidity.
Heating Time Setting Mode
Press the function button [function symbol] four times to switch to the Heating Time Setting Mode. The screen will display 'TIME', and the number shown is the remaining heating time in hours. For example, the remaining heating time is 5 hours and 30 minutes.
[Image of the display showing 'TIME' and '005.5']
The displayed value in TIME mode decreases as time progresses, similar to a countdown.
In TIME mode, press the up [up arrow symbol] or down [down arrow symbol] button to increase or decrease the time by half an hour.
Parameter Setting Suggestion
Level Set Reference Table
| Type of filament | PLA/PLA+ | ABS/ABS+ | PETG | PVA | Nylon | PC |
|---|---|---|---|---|---|---|
| Level | 1 | 2 | 2 | 3 | 3 | 3 |
Level Set for Temperature & Humidity Reference Table
| Level | 1 | 2 | 3 |
|---|---|---|---|
| Hot plate TEMP | 105°C | 116°C | 118°C |
| Inside TEMP | 40°C | 50°C | 55°C |
| Inside humidity | 34.2% | 23% | 15% |
Note: Above parameters were tested under 20°C ambient temperature and 55% ambient humidity. The internal temperature and humidity in the box may slightly change due to different environments.
Other Notes
- The desiccant included in the filament package can be used for drying.
- In case of temperature loss, do not open the box while filaments are drying.
Share Your Prints With Us @SUN
