Casablanca Ceiling Fan Installation and Operation Manual

Installation Manual for Casablanca models including: 59504, Tribeca, 60 Inch Ceiling Fan, Tribeca 60 Inch Ceiling Fan, 59504 Tribeca 60 Inch Ceiling Fan, Ceiling Fan

Casablanca Tribeca 60" - 59504 | Dan's Fan City© | Ceiling Fans, Fan Parts & Accessories

File Info : application/pdf, 19 Pages, 11.79MB

owners manual - Tribeca - 59504

PAG E

Table of Contents

www.CasablancaFanCo.com 1.888.227.2178

To register your fan, please visit: www.CasablancaFanCo.com/register
Save your receipt for proof of purchase.
Congratulations on purchasing your new Casablanca® ceiling fan! It will provide comfort and performance in your home or office for many years. This installation and operation manual contains complete instructions for installing and operating your fan.
We are proud of our work and appreciate the opportunity to supply you with the best ceiling fan available anywhere in the world.
Blades

What to Expect with Your Installation

7 feet

30 inches
2

Downrod

6
Switch Housing

PAG E

Tools Needed

Mounting Options

Ceiling Bracket

3 Ladder
Wiring

PAG E

4
Wall Control

PAG E

5
Canopy

9
Operation
16

PAG E

Maintenance & Cleaning

Troubleshooting
?? ?

PAG E

17 ?

PAG E

1
M6000-01 · 04/10/18 · © 2018 Casablanca Fan Company

What to Expect with Your Installation

If you are unfamiliar
with wiring, use a qualified electrician.

Must be able to secure the fan to building structure or fan-rated outlet box

Know your wiring

30 inches
from blade tip to nearest wall or obstruction

7 feet
from bottom
edge of blade to the floor

Assess location

You may need a friend to help you.

Ceiling angles greater than 34° will require an Angled Mounting Kit. See page 4 for details.

1 Standard Downrod for ceilings at least 9 feet high
2 Longer Downrod for ceilings 10 feet or higher

Check box to see fan weight

Assess ceiling angle

Select a downrod length

2
M6000-01 · 04/10/18 · © 2018 Casablanca Fan Company

wwwwww..CCaassaabbllaannccaaFFaannCCoo..ccoomm 1.888.227.2178
Read and Save These Instructions
This product conforms to UL Standard 507.
WARNINGS
w.1 - To reduce the risk of fire, electrical shock, or personal injury, mount fan directly from building structure and/or an outlet box marked acceptable for fan support of 70 lbs (31.8 kg) and use the mounting screws provided with the outlet box.
w.2 - To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.
w.3 - To reduce the risk of fire, electrical shock, or motor damage, use only Casablanca Solid State Speed Controls.
w.4 - To reduce the risk of personal injury, do not bend the blade brackets when installing the blade brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.
CAUTIONS
c.1 - All wiring must be in accordance with national and local electrical codes ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician.
c.2 - Use only Casablanca replacement parts.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications.

Tools Needed

www.CasablancaFanCo.com 1.888.227.2178

Ladder

Pliers

Wire Strippers

Screwdrivers

Allen Wrench (included)

Power Drill (optional)

9/64" Drill Bit (optional)

If mounting to a support structure, you will also need these tools.

3
M6000-01 · 04/10/18 · © 2018 Casablanca Fan Company

34O

CEILING

Mounting Options www.CasablancaFanCo.com 1.888.227.2178

OPTION1 OPTION 2
WALL

If you have a flat ceiling: Hang your fan by a standard downrod (included).

Standard Mounting

Support Structure

If you have an angled ceiling:
1. You will need a longer downrod (sold separately).
2. If your ceiling angle is greater than 34°, you will also need an Angled Mounting Kit (sold separately).

Angled Mounting

Use the three steps below to determine if your ceiling angle is greater than 34°

34°

FOLD
on dotted line

PLACE
against wall

SLIDE
toward ceiling

ON 1

Guide Touches BOTH Ceiling & Wall
You need ONLY a Longer Downrod
*most common

ON 2

Guide Touches Wall
but NOT Ceiling
You need BOTH a Longer
Downrod & an Angled Mounting Kit

Standard Mounting Style

Ceiling Outlet Box (required)

Use Standard Mounting to hang the fan from a flat ceiling.

SITUATI SITUATI

4
M6000-01 · 043/1007/185 · © 20185 Casablanca Fan Company

Support Structure
Angled Mounting Style

Ceiling Outlet Box (required)

Use Angled Mounting
to hang the fan from a vaulted or angled ceiling.

Ceiling Bracket

www.CasablancaFanCo.com 1.888.227.2178

OFF Turn Power
Make sure all four bumpers are still attached.
Refer to warning w.1 on pg. 2

For angled ceilings, point opening toward peak.

Use wood screws

Use machine screws

(included) when securing (provided with outlet

to support structure with box) when securing to

approved electrical outlet existing ceiling fan-rated

box. Drill 9/64" pilot holes outlet box. Make sure

in support structure to aid it is securely installed

in securing ceiling bracket and is acceptable for fan

with hardware found in support of 31.8 kg (70 lbs)

the hardware bag.

or less.

If you are unable to do this, call Technical Support at
1-888-277-2178.
5
M6000-01 · 04/10/18 · © 2018 Casablanca Fan Company

To avoid possible electrical shock, before installing your fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.

Option 1
Included (pre-assembled)
Option 2

Downrod
Standard Downrod for ceilings at least 9' high

www.CasablancaFanCo.com 1.888.227.2178

skip to next page

If you need a different downrod length follow these steps:

Longer

Downrod

for ceilings 10' or higher

Steps 1-5 to remove standard downrod pipe

Slide Slide

Sold Separately

Steps 6-10 to reassemble with new pipe

6
M6000-01 · 04/10/18 · © 2018 Casablanca Fan Company

Downrod (continued)

www.CasablancaFanCo.com 1.888.227.2178

(not to scale) CUT
& STRIP

KEEP!
KEEP

3/8" 8"

Remove the pre-installed
setscrew so that the downrod can be inserted.

Hand tighten the downrod (at least 4-5 full turns) until it stops.
8"

The wires can be cut, but leave at least 8" extending from the top of the downrod.
3/8"

7
M6000-01 · 04/10/18 · © 2018 Casablanca Fan Company

Tighten the setscrew with pliers. DO NOT
HAND TIGHTEN.
If the setscrew is not tightened securely, the fan may fall.

Downrod (continued)

www.CasablancaFanCo.com 1.888.227.2178

Put the wires and downrod through the canopy. Let the canopy sit loosely on top of the fan.

DO NOT PICK THE FAN UP BY THE
CANOPY OR WIRES. Place the downrod ball into the slot in the ceiling bracket.

8
M6000-01 · 04/10/8 · © 2018 Casablanca Fan Company

Wiring

Receiver

Note: To connect the wires, hold the bare metal leads together and
place a wire connector over them, then twist clockwise until tight.

www.CasablancaFanCo.com 1.888.227.2178
FROM CEILING

Using an orange wire connector from the hardware bag:
Connect the 3 grounding wires (green, green/yellow stripe, or bare copper) coming from the ceiling, downrod, and ceiling bracket.

green/yellow stripe (grounding)

green/yellow stripe

FROM FAN

green/yellow stripe

Place the receiver on top of the downrod assembly as shown.
Refer to CAUTION c.1 on pg. 2

OM CEILING BRAC
Turn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
9
M6000-01 · 04/10/8 · © 2018 Casablanca Fan Company

KET

Wiring (continued)

FROM RECEIVER

blue yellow

Using the orange wire connectors from the remote control hardware bag:
· Connect the yellow wire from the receiver to the black wire from the fan.
· Connect the blue wire from the receiver to the blue wire (or possibly black with white stripe wire) from the fan.

blue black

www.CasablancaFanCo.com 1.888.227.2178
FROM CEILING

Using the orange wire connectors from the hardware bag:
· Connect the black (ungrounded) wire from the ceiling to the black wire from the receiver.
· Connect the white (grounded) wire from the ceiling to both the white wire from the receiver and the white wire from the fan.

white black

white (grounded)
black (ungrounded)

FROM FAN
white

Refer to CAUTION c.1 on pg. 2

FROM FAN

FROM RECEIVER

Turn the splices upward and push them carefully back through the hanger bracket into the outlet box. Spread the wires apart, with the grounded wires on one side of
the outlet box and the ungrounded wires on the other side of the outlet box.
10
M6000-01 · 04/10/8 · © 2018 Casablanca Fan Company

Wall Control

www.CasablancaFanCo.com 1.888.227.2178

Drill Holes

Template

Painter's Tape

Screw Cut-Out

Template

Drywall Anchors

Drywall

Before

Template

Cover Plate

1. Tape the provided wall control template with painter's tape at the desired installation area.
2. Drill holes inside the four corners of the template.
Note: Make sure the wall control template is level before proceeding to the next step.

1. Using a 9/64 drill bit, drill a hole in each screw cut-out on the wall control template.
2. Using a hammer, tap a drywall
anchor found in the wall control
hardware bag into each hole until the drywall anchor is flush with the wall.

1. Using a drywall punch saw, cut out the interior shape of
the template using one of
the four drilled corners as a starting point. 2. Remove the template and the cut-out section of drywall.

After
1. Insert the wall control into the dry wall cut out.
2. Align the screw holes in the wall control with the drywall anchors.
3. Install the cover plate using a Phillips Head screwdriver to secure the two cover plate screws found in the wall control hardware bag through the wall control and into the drywall anchors.

If you are using a outlet box for wall control installation, the wires coming from the wall control must be grounded using the attached green wire. If not placed in an outlet box, cap
the green wire coming from the wall control with an included wire nut.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
11

Canopy

Screw Holes

www.CasablancaFanCo.com 1.888.227.2178

Position the canopy so that, when lifted into place, the canopy fits into
the hanging bracket as shown.

Lift the canopy into place so that the screw holes are aligned.

Insert the two canopy screws found in the hardware bag.

Blades

www.CasablancaFanCo.com 1.888.227.2178

Shipping Ring

Using the provided Allen wrench, attach each blade to the blade iron assembly using three barrel nuts, found in the hardware bag, and three decorative screws, found in
the hardware bag.
Note: You have the option to install the blade above or below the blade iron. In either instance, you may place the decorative screws and barrel nuts
facing up or down.

Remove the two orange shipping rings from the motor by lifting up on the edges of
the rings.

Align the five holes in the blade
iron assembly and the decorative ring with the five holes in the bottom
of the motor and partially install the five blade iron screws, found in
the hardware bag. Once all five
screws are partially installed, tighten them securely.

Switch Housing

www.CasablancaFanCo.com 1.888.227.2178

Screw two housing assembly screws from the hardware bag halfway into the motor housing. It does not matter
which two screw holes you choose.
Note: Fan style may vary.

Feed the wire plug through the center hole of the upper switch housing, then wrap keyhole slots around the screws and
twist counterclockwise.
14
M6000-01 · 04/10/18 · © 2018 Casablanca Fan Company

Insert the third screw, found in the hardware bag, into place and
then tighten all three screws.
Make sure the upper switch housing is securely attached to the mounting plate. Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling.

Switch Housing (continued)

www.CasablancaFanCo.com 1.888.227.2178

Connect the plugs from the upper and lower switch housings. Make sure to line up the colored markings on the connectors.

Lift the lower switch housing up until the holes line up with the screw holes in the upper switch housing. Install the three
switch housing screws, found in the hardware bag.
15
M6000-01 · 04/10/18 · © 2018 Casablanca Fan Company

YCOOUNG'RRAETUDLAOTIONNES!!
Make sure the lower switch housing is securely attached to the upper switch housing. Failure to properly secure all 3 assembly screws could result in the switch housing fixture falling.

Operation

www.CasablancaFanCo.com 1.888.227.2178

Battery
Battery Holder
Battery Door
Before operating the wall control, press on the battery door to eject it. Unscrew the battery holder. Insert the battery, found in the control hardware bag, with the positive (+) side facing
downward. Reinstall the battery holder and reinsert the battery door
into the wall control.

ON Turn Power

Fan Speed
Lights Down Reverse

(Low) (High)

Fan Speed
Lights Up
Fan Power

The remote transmitter is already paired to the receiver and ready to use.
Note: If you would like to operate multiple fans or multiple remotes, or if your remote is not working,
please see the Troubleshooting section at the end of this manual.

Battery Holder
Quickly press the up or down arrow to turn the lights off and on. Hold the up or down arrow to dim or raise the light level. The reverse button changes the direction that the blades turn. The power button
turns the fan off and on.

Maintenance & Cleaning

www.CasablancaFanCo.com 1.888.227.2178

Reverse Button
(a)
ON Turn Power

Battery

(b)

The reverse button on the wall control changes the air flow
direction. In warm weather, use (a) downward air flow pattern. In cold weather, use (b) upward
air flow pattern.

Battery Door
To change the battery, push on the battery door to eject it. Remove the battery using a small Phillip's head screwdriver. Replace with same type battery, making sure the (+) side is facing down. Replace battery holder and battery door.

For cleaning the fan, use soft
brushes or cloths to prevent scratching. Cleaning products
may damage the finishes.

Troubleshooting

www.CasablancaFanCo.com 1.888.227.2178

Fan doesn't work · Press a fan speed button (1-4).
· Check the circuit breaker to ensure the power is turned on.
· Check the wall control battery.
· Make sure the blades spin freely.
· Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram on pages 9-10.
· Check the plug connection in the switch housing.

Excessive wobbling · Tighten all of the blade and
blade iron screws until they are snug.
· Turn the power off, support the fan carefully, and check that the hanger ball is properly seated.
· Use the provided balancing kit and instructions to balance the fan.
Noisy Operation · Tighten the blade and blade
iron screws until they are snug.
· Check to see if any of the blades are cracked. If so, replace all of the blades.

Remote does not work
· Make sure the battery is installed correctly.
· Install a new battery.
· If the remote still does not work, you may need to pair your remote. To prevent faulty operation, please disconnect power (at the wall switch, breaker, or fan) from all other ceiling fans within range while pairing. To pair: cycle power to the fan by turning power off and back on at the wall switch (or circuit breaker if necessary). Within three minutes, press and hold both the Fan Off button and the 4 button for four seconds to pair the remote. If applicable, the fan will turn on and the lights will flash and stay on to indicate successful pairing.

AUTHORIZED SERVICE CENTERS
For the most updated list of
Casablanca Authorized Service
Centers, visit www.CasablancaFanCo.com or call toll free 1-888-227-2178.

Troubleshooting (continued)
Installing Multiple Fans with Independently Operating Remote Controls

www.CasablancaFanCo.com 1.888.227.2178
Installing One Fan Operating on Multiple Remote Controls

To install multiple fans with independently operating remote controls, there is no need to perform any pairing procedures. Each set of receiver/transmitter is already paired. Simply
install each receiver into a fan and use the appropriate transmitter to operate each fan. If your remote is not working, see the "Remote does not work" section on the previous page.
Installing Multiple Fans Operating on a Single Remote Control

To have multiple remote controls operate one fan, you must pair each additional transmitter to the receiver in the fan. The transmitter that shipped with your fan is already paired. Note: To prevent faulty operation, please disconnect power (at the wall switch, breaker, or fan) from all other ceiling fans within range while pairing.
For each additional transmitter, cycle power to the fan by turning power off and back on at the wall switch (or circuit breaker if necessary). Within three minutes, press and hold both the Fan Off button and the 4 button for four seconds to pair the remote. If applicable, the
fan will turn on and the lights will flash and stay on to indicate successful pairing.
"Unpairing" Procedure for Faulty Operation of Remote Controls
X

To have multiple fans operated by a single remote control, you must pair the transmitter to each additional receiver. The receiver that shipped with your fan is already paired to the transmitter.
Note: To prevent faulty operation, you MUST disconnect power (at the wall switch, breaker, or fan) from all other ceiling fans within range while pairing each fan.
For each additional fan, ensure that a compatible receiver is installed. Disconnect power from all other fans while pairing. To pair: cycle power to the fan by turning power off and back on at the wall switch (or circuit breaker if necessary). Within three minutes, press and hold both the Fan Off button and the 4 button for four seconds to pair the remote. If applicable, the
fan will turn on and the lights will flash and stay on to indicate successful pairing.

If a transmitter is mistakenly operating a fan, you need to "unpair" the transmitter from that fan's receiver. The "unpairing" procedure is the same as the pairing procedure.
Note: To prevent faulty operation, you MUST disconnect power (at the wall switch, breaker, or fan) from all other ceiling fans within range while "unpairing" a fan.
Disconnect power from all other fans while "unpairing." Then, cycle power to the fan you wish to "unpair" by turning power off and back on at the wall switch (or circuit breaker if necessary). Within three minutes, press and hold both the Fan Off button and the 4 button for four seconds to "unpair" the remote. If applicable, the fan will turn off and the
lights will flash and turn off to indicate successful "unpairing."

References

Adobe PDF Library 15.0 Adobe InDesign CC 13.0 (Macintosh)

	Casablanca Ceiling Fan Installation and Operation Manual Comprehensive guide for installing and operating Casablanca ceiling fans, including tools needed, mounting options, wiring, wall control setup, and troubleshooting.
	Casablanca Fan Company Limited Lifetime Warranty Information Official limited lifetime warranty details for Casablanca ceiling fans, covering motor and other parts, including exclusions and service procedures from Hunter Fan Company.
	Casablanca Ceiling Fan Installation and Operation Manual Comprehensive guide for installing and operating a Casablanca ceiling fan, covering preparation, tools, mounting options, wiring, blade attachment, switch housing, maintenance, and troubleshooting.
	Casablanca Verse Service Kit Instructions: Removing Your Existing Light Kit Step-by-step instructions for removing the existing light kit from a Casablanca Verse ceiling fan, including details on component removal and disconnection.

References

Related Documents