Eterna PUSHLED LED Time Delay Push Switch
Installation Instructions
A guide for qualified electricians
Product Information
Model: PUSHLED
Product Type: LED Time Delay Push Switch
Pack Contents:
- 1 x Fitting
- 2 x Fixing screws
- 2 x Blanking plugs
These instructions are provided as a guideline to assist you. Please read these instructions before installation and retain for future reference.
Important Safety Information
CAUTION HIGH VOLTAGE - ISOLATE BEFORE INSTALLING / ADJUSTING
Always ensure the mains power is switched off and the appropriate circuit fuse is removed before commencing any installation or adjustment work.
As the buyer, installer, and/or user of this product, it is your responsibility to ensure that this fitting is fit for the purpose for which you have intended it. Eterna Lighting cannot accept liability for loss, damage, or premature failure resulting from inappropriate use.
This product is designed and constructed according to the principles of the appropriate British Standard and is intended for normal domestic service. Installation must comply with the Building Regulations.
Do not overload the switch. Check that the total wattage of the switched load does not exceed the maximum listed capability.
Disconnect the switch from the electrical supply before flash or high voltage testing.
Suitable for indoor use only. This product is only suitable for use in living areas (not for areas constantly subject to moisture).
Before making fixing hole(s), check that there are no obstructions hidden beneath the mounting surface, such as pipes or cables.
Do not attach to surfaces which are damp, freshly painted, or otherwise electrically conductive (e.g., metallic surfaces).
If a new electrical supply is required for the installation location, the supply must conform with the requirements of the Building Regulations.
This switch is double insulated. Do not connect any part to earth.
You are advised at every stage of your installation to double-check any electrical connections made. After installation, electrical tests should be carried out as specified in the Wiring Regulations (BS7671), as referred to in the Building Regulations.
Installation Steps
- Your new time lag switch can be installed as a direct replacement for a normal one-way wall switch.
- The switch body will fit onto a standard wall box using the screws supplied.
- Lever the mounting screws out from the rear of the case using a small screwdriver.
- Connect the switch to the live supply wire at the "LIVE IN" terminal.
- Connect the live wire from your light fitting or other appliance to the "LIVE OUT" terminal.
- Do not connect any neutral wires.
- Do not connect any earth wires.
- Do not connect any ring live wires.
- Adjust the time delay control to minimum (12 seconds) for testing.
- Fit the switch to the wall box or pattress box and secure using the screws supplied.
- Restore the power and test the switch.
- If any adjustments to the time delay are required, switch off the electricity at the mains before removing the switch to access the control.
Wattage Selection
To adjust for the required load, place the plastic cap over the appropriate pins:
For 5-20W loads: Place CAP over the 5-20W pins.
For 20-150W loads: Place CAP over the 20-150W pins.
For 150-300W loads: Place CAP over the 150-300W pins.
Visual Description of Switch Internals
The rear of the switch unit displays connection terminals clearly marked "LIVE IN" and "LIVE OUT". A multi-pin connector block, labeled JP1, is provided for setting the load wattage. Adjacent to JP1 are three sets of pins, each accompanied by a plastic cap. These caps are used to configure the switch for specific load ranges: 5-20W, 20-150W, and 150-300W. A rotary control dial is also visible, used for adjusting the time delay, marked with indicators for "Shorter - 12 seconds" and "Longer - 12 minutes". Prominent cautionary text, "CAUTION HIGH VOLTAGE ISOLATE BEFORE INSTALLING/ADJUSTING", is printed near the connection terminals.
Operation
Normal - Off State: The red indicator light is illuminated inside the switch.
On State: The red indicator light inside the switch is off, and power is supplied to the connected light fitting or appliance.
Once the push button is pressed, power is supplied to the appliance for a duration set by the internal control, ranging from approximately 12 seconds to 12 minutes. The power will be interrupted at the end of the set time cycle, irrespective of any subsequent button presses. After the time cycle has elapsed and power is interrupted, the button can be pressed again to initiate a new cycle.
Product Capability
Minimum Load: 5W
Maximum Load: 300W
This switch is suitable for switching the following loads:
- Incandescent lighting
- Fluorescent lighting
- LED lighting
Product End-of-Life Information
Regulations require the recycling of Waste from Electrical and Electronic Equipment (European "WEEE Directive" effective August 2005; UK WEEE Regulations effective 2nd January 2007). Environment Agency Registered Producer: WEE/GA0248QZ.
When your product comes to the end of its life, or you choose to replace it, please recycle it where facilities exist. Do not dispose of with household waste.
Cleaning and Care
Clean this fitting only with a soft dry cloth. Do not use any chemical or abrasive cleaners.
If You Experience Problems
If you believe your product is defective, please return it to the place where you bought it. Our Technical Team will gladly advise on any Eterna Lighting product, but may not be able to give specific instructions regarding individual installations.
Issue 1222
Email: sales@eterna-lighting.co.uk / technical@eterna-lighting.co.uk
Visit our website: www.eterna-lighting.co.uk
UKCA Mark, CE Mark, [Electronic Switch Symbol]
Made in China
LIGHTING.CO.UK
